Post by atcprojectteam on Modbus Function Code 15, writing multiple coils ^{CODESYS Forge talk (Post)}
Hi all, I am using an RSTI-EP I/O card along with the EPXMBE101 Modbus/TCP network adapter. I have a Control Standard L license. I successfully connected to the I/O card via Modbus and can read inputs without any issues. However, when I try to write to the digital output modules using function code 15, I am unable to make any changes. Here’s what I have done so far: I created a small project using Structured Text. I set up Modbus channels (as shown in the attached image) and mapped the pins. When I use cyclic mode, the connection results in an error. However, when I use the rising edge, the connection works, but I don’t see any changes on the I/O card. For the output module, I assigned one bit to high. After that, I ran CODESYS Control Win V3. (Should I be running the PLC as well?) I built the program, but I am not receiving any response from the I/O card. Could you please advise on what might be causing this issue?
Last updated: 2025-02-26

Post by macman on Codesys 3.5 OPC UA Client to Kepware OPC UA Server ^{CODESYS Forge talk (Post)}
Hi, I have problem with connecting Wago PLC WAGO 750-8212/0025-0002 configured as OPC UA client to Kepware OPC UA Server. I am using Codesys 3.5.19.70. What I did so far. To the Codesys project I added object Data Source Manager and configured connection OPC UA like below: pic 1 Then I can browse the OPC server tags in “Variables” tab after prior trust on the server side of the client certificate created in the “Communication” tab: pic 2 Additionally second certificate has been created in Codesys for runtime process in “Security screen” as well as the server certificate was approved here: pic 3 But when I compiled project, downloaded it to PLC and go to RUN I can’t read selected in “Variables” tab, OPC Server tags. I am getting such error (ID: 7001): pic 4 All two PLC certificates has been trusted in OPC server (Kepware) side: pic 5 and Kepware server configuration look like this: pic 6 I can easily connect using third party OPC UA client UaExpert to Kepware server without problem. In attachment I added also log from Kepware OPC UA server. pic # - this specifies the number of a concrete graphic from one of the collective in attachment
Last updated: 2025-04-02

Post by wbj0t on System libs and I/O Drivers ^{CODESYS Forge talk (Post)}
Hi everyone. My question about: where I can learn (read or watch) an info about codesys workflow through the system IO libs? I want to know how to implement I/O drivers by my self. In the system libs I see many interfaces, methods etc... But there is no explanation about them, just names of methods and fields of the FBs. I know about this page: https://forge.codesys.com/drv/io-drivers/doc/Generic/ There is so BIG the device description file and not so clear explaining of the attributes and elements, also some elements or attributes missed at it all. Yes, there are code examples on this page, but, so shortly and, for example, code about Modbus drivers is absent. And even if I try to add the IoDrvFB with lib, I get and error, something like: "failed to load IoDrvFB driver". And what about the book of codesys that written by Gary Pratt? Is there information about system libs and drivers in this book more clearly? Thank you :)
Last updated: 2024-02-02

Post by mtho on JSON Utilities - JSON file written with invalid structure ^{CODESYS Forge talk (Post)}
I'm using the JSON Utilities SL library to write configurations in my program to a file. I'm generating the JSON data using the builder function block and all appears to work correctly. When I write the jsondata to file, I'm finding that some of the JSON elements are not being written in the right location in the file. Rather than writing they keys under the parent object, they get written outside the root JSON object at the end of the file. If I then try to read the file back into the program, I get an invalid_structure error. I don't get any errors when populating the JSON data or when writing the file. I attached an example of the JSON writer output. The problems begin with key P200. Each P200 should go under MBR1 through MBR3. Among the rest of the keys, they are supposed to be under different parent objects. I am using default values for wsLineBreak and encoding.
Last updated: 2024-03-06

Post by gatto on Backtick identifiers ^{CODESYS Forge talk (Post)}
Hello, I’m in Codesys 3.5.20.40 and I try to declare the variable ´var1´ but I get an error. here : https://content.helpme-codesys.com/en/CODESYS%20Development%20System/_cds_rules.html i read : Backtick identifiers By using backticks, characters can also be used in identifiers that are not normally permitted in identifiers, such as special characters. The acute accent character is used for backticks: ´ (Unicode: U+02CA) The use of backticks is recommended in order to be able to use the same identifiers in CODESYS as in other programming languages or documents, such as circuit diagrams. Any character may be used between two backticks, except line breaks and other backticks. Keywords are also allowed as identifiers between backticks. Examples: ´Variable+9´ ´INT´ The backticks are part of each identifier and therefore var1 and ´var1´ are two different identifiers. Example PROGRAM PLC_PRG VAR var1 : INT; ´var1´: INT; END_VAR var1 := var1 + 1; ´var1´ := 12; Are there any limitations or is something missing in my development environment?
Last updated: 2025-10-28

Post by nixola on CmpCharDevice blocks gpiochip access on Raspberry Pi 5 since update from SP18 to SP21 ^{CODESYS Forge talk (Post)}
Hi, I added the following lines to /etc/codesyscontrol/CODESYSControl_User.cfg: [CmpCharDevice] PermittedPath.0=/dev/i2c* PermittedPath.1=/dev/spidev* PermittedPath.2=/sys/class/gpio/* PermittedPath.3=/dev/gpiochip* However, I'm still unable to read or control GPIO pins from any CODESYS application. Specifically, setting the pin direction (and, thus, the IoDrvGpioSysfs driver configuration) fails, with a rather non-descript error in the logs: Description Component Setting direction failed for GPIO pin 586 IEC Update configuration failed from driver IoDrvGPIOSysfs CmpIoMgr I'm running CODESYS Control for Linux ARM64 SL version 4.21.0.0; it's running in rootless mode, as the codesyscontrol user, but said user is in the gpio group and can otherwise normally interact with GPIO, both via gpioset/gpioget and via the sysfs driver in /sys/class/gpio/. The system is a custom 64-bit Raspberry OS based distro, running on a Raspberry Pi CM5 on kernel 6.18.34 with PREEMPT_RT scheduling.
Last updated: 2026-07-21

Post by pernockham on How to recognize licenses SMALL, MEDIUM, LARGE by CmpCodemeter ^{CODESYS Forge talk (Post)}
Im trying to read out active license by CmpCodeMeter but am not sure of the combination of ProductCode and FeatureMap that each of CONTROL, VISU and COM / SMALL, MEDIUM, LARGE equals. Started by trying CodeMGetContentByFirmcode (and productCode) expecting error 18 / Not Available if asking for a higher level of license compared to what I know is active, but function just returned the requested productcode and a featuremap Is this the way or is it better to use CodeMOpen? Which seems to also require a featureCode. Where can I find info on required featureCode? ProductCodes according to google: Control (PLC Runtime) Small (S) 16#00002FFF 12287 * Medium (M) 16#00003000 12288 Large (L) 16#00003001 12289 Visualization (WebVisu) Small (S) 16#00003002 12290 Medium (M) 16#00003010 12304 * Large (L) 16#00003003 12291 Communication (Com) * Small (S) 16#00003004 12292 Medium (M) 16#00003005 12293 Large (L) 16#00003006 12294 Thanks!
Last updated: 2026-10-06

Post by egr99 on Modbus TCP Server connection is ESTABLISHED but all holding registers are value 0? ^{CODESYS Forge talk (Post)}
Hi there, Read the above description and experienced the same: Reading coil/discrete input/input register/holding register doesn't fill the mapped I/O variable. Any suggestions? Defined (see attachment): - Ethernet (with parameters according to the used Ethernet adapter of my Windows 11 laptop) - -Modbus TCP Client - - -LOGO231 as Modbus TCP Server - - -WS242 as Modbus TCP Server (WaveShare Modbus TCP <-> RTU converter) - - - -WS242_01 as Modbus Server, COM port (slave-id 1 RTU) - - - -WS242_03 idem (slave-id 3 RTU) - - - -WS242_11 idem (slave-id 11 RTU) Writing coil/holding register works from a mapped I/O variable works fine. Verification of Modbus traffic with WireShark: QUERY to and the RESPONSE of all slave-ids are correct Status of all defined is CONNECTED, RESPONSE_SUCCESS, RUNNING etc. Request counters increase with expected frequency. Error counter = 0. (To have all counters works fine I had to change Modbus TCP Client's parameter OptimizationON to FALSE). LOGO231 works fine: values in mapped I/O conform expectation WS242 without Modbus Server, COM port and with defined channels (for only 1 slave-id possible) works fine. PLC Settings: Update I/O while in stop: I see xBusy changing from FALSE to TRUE and vice versa. Always update variables: Enabled 1
Last updated: 2026-04-05

Post by mankh on Legacy IFM CANopen I/O modules with CR710S / CODESYS 3.5 ^{CODESYS Forge talk (Post)}
Hi, I am migrating an existing IFM system from CR0020 + CODESYS 2.3 to CR710S + CODESYS 3.5. The existing CANopen I/O modules are: CR9011 CR2042 CR2011 My questions are: Can these legacy IFM CANopen modules be used as slaves with the CR710S CANopen Master? Can their existing EDS files be imported directly into CODESYS 3.5? Are there any known compatibility issues with the old IFM EDS files, PDO mapping, or startup SDO configuration? Has anyone successfully used these modules with a CR710S? If so, could you share the recommended configuration procedure? The goal is to replace the CR0020 with a CR710S while keeping the existing CANopen I/O modules
Last updated: 2026-09-25

Post by kunz on Profinet Device keeps abort connection with AR alarm.ind(err) ^{CODESYS Forge talk (Post)}
Can somebody explain what the error Connection aborted: AR alarm.ind(err) exactly mean? I have the same Problem and dont know how to solve the issue
Last updated: 2023-08-21

Post by roundex on CSVReaderInit returns error : INVALID_HANDLE ^{CODESYS Forge talk (Post)}
Could you please give me an example where to select new path in plc. Right now my csv files are placed into /home/user/csvfiles
Last updated: 2023-08-30

Post by totorovic on CSVReaderInit returns error : INVALID_HANDLE ^{CODESYS Forge talk (Post)}
Thank you for the return. The path targets to a CFast card. User has R/W access to it. We will try to change it.
Last updated: 2023-08-31

Post by marekxc on Error C0521 - unknow compiler ^{CODESYS Forge talk (Post)}
Select in tree "DEVICE", right-click and select "Update Device" Select "Library manager" and Change the version of the Library (down manualy). Samoetimes "Try reload Library". If you open a project version 3.5.19 in version 3.5.16, there are difficulties.
Last updated: 2023-09-02

Post by nyee on Project compiling error in Simulation mode ^{CODESYS Forge talk (Post)}
Hi, I have a similar issue - we have been using codesys V3.5.16.20 Do you have any suggestions or confirmation that this will work with a different version of codesys and Pi extension
Last updated: 2023-09-07

Post by fleaplc on FILE_OPERATION_DENIED ^{CODESYS Forge talk (Post)}
By using the CAA FILE library (FB FILE.Open) (raspberry pi, codesys 3.5.19.0) I always get the error FILE_OPERATION_DENIED The file exist, it has r/w/x access and path is correct... Some idea to fix it?
Last updated: 2023-09-25

Post by derpaul on Official MQTT-Client: MAX_RECEIVE_BUFFER_SIZE_EXCEEDED ^{CODESYS Forge talk (Post)}
Thank you very much so far - As I finaly decided to make an update on the PFC200 - as I've to get it up and running again. But something failed there and no I'm having an other Problem :-( I'll come back to this, when the error comes back!
Last updated: 2023-09-28

Post by simond on The required device description is not installed.. ^{CODESYS Forge talk (Post)}
Hi folks, can someone please tell me how to go about fixing this issue? I am getting this error when I implement an instance of the J1939_Manager. Thanks Simon
Last updated: 2023-10-03

Post by tomas111 on Help with error C0142 ^{CODESYS Forge talk (Post)}
There was an exact mistake. I did as they wrote. I created a visualization and transferred it from the old one and everything works. CS 3.5 SP 19. Thank you.
Last updated: 2023-10-04

Post by damian177 on MQTT_client disconnect when call MQTT_sunscribe ^{CODESYS Forge talk (Post)}
Probably I have the same problem, When I connect to broker and try subscribe to much topics then the client return error, did you solve your problem ?
Last updated: 2023-10-10

Post by chris12345 on FILE_OPERATION_DENIED ^{CODESYS Forge talk (Post)}
Hello everyone, I am using SP19 patch 2 on a Kunbus device with runtime package 4.9.0.0. I am having the same problem as mentioned above. With the FB File.open I get the FILE_OPERATION_DENIED error. I have also tried the path /var/opt/codesys/PlcLogic. Any advice? Chris
Last updated: 2023-10-17

Post by vincentd on Datasource OPC UA Client error ID:7012 ^{CODESYS Forge talk (Post)}
I had some help from Codesys to debug this problem. It seems there was a problem within the target (a bug?). I only used for a proof of concept. Possibly it will work with a new version of the target
Last updated: 2023-11-21

Post by to-ke on Errors with VisuUserManagement library ^{CODESYS Forge talk (Post)}
Hallo zusammen, hi all, ich habe den gleichen Fehler. Auf einem Raspberry Pi geht der Fehler weg, wenn ich alles bereinige und dann vollständig übersetze. Wenn das Projekt im Codesys Development System wieder neu geladen wird ist der Fehler aber wieder da. Mit eine Win V3 x64 PLC kann ich den Fehler nur unterbinden wenn ich auf der HMI das VUM_Login einbinde. Dieses brauche ich aber nicht, da ich die HMI für das User Management selbst gestaltet habe. Das funktioniert auch. I have the same error. On a Raspberry Pi the error goes away if I clean everything and then compile completely. When the project is reloaded in the Codesys Development System, the error returns. With a Win V3 x64 PLC I can only prevent the error if I integrate the VUM_Login on the HMI. But I don't need this because I designed the HMI for user management myself. That works too. Anyone have an idea to fix this problem. Many thanks
Last updated: 2024-07-09

Post by dennisyhli on Ethernet IP Connection timeout ^{CODESYS Forge talk (Post)}
I use ethernet ip scanner and the connection type is set to multicast. After running the PLC, the ethernet IP will have a connection timeout every 10 seconds. What is the reason for this error?
Last updated: 2024-08-16

Post by remoyang on Package manager ^{CODESYS Forge talk (Post)}
When I opened the package manager, it comes up the error as attached. I tried to uninstall and re-install many times it has the same issue
Last updated: 2024-08-16

Post by simon001 on CAN communication settings for USB2CAN-C ^{CODESYS Forge talk (Post)}
I am using the Innomaker USB2CAN-C device to communicate via CAN in the Windows version of CODESYS, but I am encountering error code 27E2, which indicates that the driver is not found. Could you please advise on how to proceed with the CODESYS settings?
Last updated: 2024-08-18

Sort by relevance or date