Post by gseidel on Hydraulic Axis Controller ^{CODESYS Forge talk (Post)}
Hi kumareasu, yes, correct. Best regards, Georg
Last updated: 2024-04-30

Post by jonasz on Discontinuity of A/B/C axis movement. ^{CODESYS Forge talk (Post)}
PrtScr
Last updated: 2024-05-09

Post by imdatatas on MC_CamIn did not work properly with SMC_FreeEncoder on SoftMotion 4.17.0.0 ^{CODESYS Forge talk (Post)}
Hello, I am facing a problem with the new Softmotion 4.17.0.0 version. Has anyone encountered a similar problem, what is the solution? I would be happy if you could share it. Problem description: -- "SMC_FreeEncoder" encoder axis is the master, -- The motor of the servo driver on the EtherCAT bus is the slave axis. -- When the MC_CamIn block executed, the InSync output is activated. However, although the master encoder axis position value changes, there is no movement in the slave servo axis! Test steps: 1-) EtherCAT servo axis installed, configured and motion test was performed with MC_Jog. No problem. 2-) Softmotion general axis pool > SMC_FreeEncoder was added and pulse amount configuration was performed. No problem. 3-) Incremental encoder actual count value was transferred to the "SMC_FreeEncoder.diEncoderPosition" variable as DINT under the ethercat task in every cycle and the encoder axis position value was observed. No problem. 4-) A simple CAM table with a 1:1 ratio was created under the project tree. (For example: Simply, when the encoder rotates 1 turn, the motor will rotate 1 turn.) 5-) The SMC_FreeEncoder axis enabled with MC_Power and brought to the StandStill state. 6-) The MC_CamTableSelect block was run with default input values ​​(all absolute) and only the Cam table name was specified. The Done output was seen successfully. No problem. 7-) The MC_CamIn block was activated with default input values ​​(absolute) and only the master encoder axis name, slave servo axis name, CamTableID input pins was specified and then "Execute" input set to TRUE. 8-) The InSync output information of the MC_CamIn block observed as TRUE. However, although the encoder axis value changed, the position value of the slave axis did not change at all, it did not move. It always remained at 0.0mm. 9-) When I repeated the same steps above, only changing the master axis to SM_Drive_Virtual instead of FreeEncoder and gave movement to the virtual axis, this time the slave axis moved successfully. However, when the same steps and operations are performed with the same IDE just downgrade SoftMotion version from 4.17.0.0 to 4.10.0.0, everything works normally and without problems as expected in MC_CamIn block with FreeEncoder master. (By the way, The used IDE version is Codesys V3.5 SP20patch3.) Best Regards Imdat
Last updated: 6 days ago

Post by reinier-geers on Pointer Axis ^{CODESYS Forge talk (Post)}
I want to make a FB of MC. But i need a variable for Axis. How do i have to declare that ? ptAxe : AXIS_Ref_SM3; //:= SM_Drive_ETC_Delta_ASDA_A2 ; this is somehowe a problem
Last updated: 2024-01-12

Post by victor on Trend-Trace / Time x-axis ^{CODESYS Forge talk (Post)}
Good morning, I am new to codesys, I am currently manipulating the Trace and Trend elements and I would like to know if it was possible to configure a variable or a trigger to reset the "X" axis to 0. have a good day.
Last updated: 2024-01-26

Post by reinier-geers on Axis declare ^{CODESYS Forge talk (Post)}
In motioncontrol every block start with Axis. How can i make a variable to make my own FB ? Somthink like : _Axe : pointer to Axis_Ref_MC := Axis_1 ;
Last updated: 2024-02-13

Post by manuknecht on Creating softmotion axis dynamically ^{CODESYS Forge talk (Post)}
Hi I was wondering the same thing. I managed to dynamically add an EtherCat Slave but I could not find out how to add a softmotion axis to it. Does anyone have an answer to this? Thanks in advance!
Last updated: 2024-02-21

Post by k2saki on Discontinuity of A/B/C axis movement. ^{CODESYS Forge talk (Post)}
Hello. Good morning. I have a same problem with short-segment G01 in GCode even in XY Axis. ( I'm using SMC_ReadNcFile2, SMC_NcInterpreter, SMC_CheckVelocities before IPO , watching Youtube tutorial video.. ) How did you solve this problem ?
Last updated: 2024-04-29

Post by mubeta on Some 'pathetic' errors in SoftMotion program ^{CODESYS Forge talk (Post)}
Hello everyone, I have a very simple program for the process, but it's driving me crazy and I can't see the problems I'm left with: Short topological description: Dual Core Berghof controller with softmotion runtime version 3.5.19.30; Two axes with servodrive on canopen bus, clocked distributed from master; Ethercat I/O node; 2 ms ethercat task, 2 ms canopen bus cycle time; I/O objects of the canopen master and canopen drives connected to the ethercat task cycle; Problem 1: Two separate programs each manage their own axis and drive, with separate state machines. A first axis moves primarily in velocity, except having to position itself absolutely at a predetermined point at the end of the job; the second axis, on the other hand, is a paper unwinder that changes, for each job cycle, from actions in absolute, relative, and cam displacement with the master axis. Well, the state machine of both axes was written in such a way as to call running the useful FB and change it on state change in this way: CASE i_stateMachine OF 0: o_Power(Enable := TRUE, bRegulatorOn := FALSE, bDriveStart := FALSE, Axis := o_PaperUnwinderAxis); o_MoveAbs(Execute := FALSE, Axis := o_PaperUnwinderAxis); o_MoveRel(Execute := FALSE, Axis := o_PaperUnwinderAxis); o_CamSelect(Execute := FALSE, Master := o_MachineAxis, Slave := o_PaperUnwinderAxis, CamTable := cam_PaperUnwinder); o_CamIn(Execute := FALSE, Master := MachineEncoder, Slave := o_PaperUnwinderAxis); o_CamOut(Execute := FALSE, Slave := o_PaperUnwinderAxis); o_SetPosition(Execute := FALSE, Axis := o_PaperUnwinderAxis); IF ... THEN i_StateMachine := 10; END_IF; 10: o_Power( Enable := TRUE, bRegulatorOn := TRUE, bDriveStart := TRUE, Axis := o_PaperUnwinderAxis ); IF o_Power.Status THEN i_StateMachine := 20; END_IF; 20: (* Avanzamento carta *) o_MoveAbs( Execute := TRUE, Position := o_Somewhere, Velocity := 25.0, Acceleration := 3666.7, Deceleration := 3666.7, Jerk := 48000.0, Direction := MC_DIRECTION.positive, Axis := o_PaperUnwinderAxis ); IF o_MoveAbs.Done THEN o_MoveAbs(Execute := FALSE, Axis := o_PaperUnwinderAxis); i_StateMachine := 30; END_IF 30: d_HomingPosition := ...; o_SetPosition( Execute := TRUE, Position := d_HomingPosition, Mode := FALSE, Axis := o_PaperUnwinderAxis ); (* ... *) IF o_SetPosition.Done = TRUE THEN o_SetPosition(Execute := FALSE, Axis := o_PaperUnwinderAxis ); o_LogServer.Append(sMessage := '...', lscClass := LOGSERVER_CLASS.ALWAYS, sdt := o_CommonsMgrData.systime.sdtLocal); i_StateMachine := 40; END_IF; 50: ... The code above is a sketchy example of what I wanted to write. But it gives me a spot problem: in some, the state change results in a drive error, which is unrecoverable except with a reinitialization via SM3_ReinitDrive(). Things are improved a little if in the program I always run the call of all softmotion blocks in this way: o_Power(Axis := o_PaperUnwinderAxis); o_Jog(Axis := o_PaperUnwinderAxis); o_Halt(Axis := o_PaperUnwinderAxis); o_MoveAbs(Axis := o_PaperUnwinderAxis); o_MoveRel(Axis := o_PaperUnwinderAxis); o_CamIn(Master := MachineEncoder, Slave := o_PaperUnwinderAxis); o_CamOut(Slave := o_PaperUnwinderAxis); If I don't execute all the calls of all the motion FBs used, when exchanging machine state often (but not always), the axis goes into error with event id THE_FB_WASNT_CALL... Done a little diagnostics it seems that the FBs return the bDone, before they are completely terminated. I tried doing the machine state exchange not with the bDone bit of the FBs, but with the 'standstill' state of the axis. It didn't seem to change anything. Problem 2: During the use SM3_ReinitDrive() I get the erro in the log: "NetID 0: SDO read error for object 16#607C..." Assuming that the device involved it's one of the two servodrive, (no others device are present in the network), I don't found any object 0x607C in the 'possible object list in/out' of the two drive, and I don't understand where this object can be listed. So any ideas and suggestions regarding these two issues will be very, very welcome. If you need the source project, I am willing to send it.
Last updated: 2024-07-17

Post by kleeswi on Visualization scaling problem with B&R T30 panel ^{CODESYS Forge talk (Post)}
I have found a work around. I have written a python scripts that runs on user login (entry in .bashrc) which overwrites the webvisu.htm and webvisu.cfg.json file with the configuration for the B&R T30 panel (resolution and disable scaling). First I tried to add this setting to the the CODESYSControl.cfg, but that does not work following the big CODESYS Control V3 Manual. [CmpTargetVisu] Application.WindowPositionX=0 Application.WindowPositionY=0 Application.WindowSizeWidth=800 Application.WindowSizeHeight=480
Last updated: 2024-07-30

Post by spiessli on Softmotion axis to CANopen Maxon IDX drive ^{CODESYS Forge talk (Post)}
Hi, I want to use Maxon IDX drives for some simple robotic applications. I have used Maxon's Epos for generating a DCF file to import in Codesys (attached). Then I can add the IDX motors under a CANopen manager in the device tree. Unfortunately, I cannot add a "softmotion axis" to the IDX motors. Now I am wondering, why? Without being able to attach a softmotion axis to the device in the device tree, the use of the motor is greatly reduced... spiessli
Last updated: 2024-01-05

Post by sahil-koul on Touch Probe Continuous Trigger ^{CODESYS Forge talk (Post)}
Hi everyone. Can anyone tell how to do continuous trigger function of probe in codesys and change scaling of servo online in program
Last updated: 2024-06-16

Post by janderson on Ethercat scan for devices not picking up EL7041 as a softmotion axis ^{CODESYS Forge talk (Post)}
also my ethercat bus won't run.
Last updated: 2023-09-02

Post by tk096 on Axis_Ref_SM3.perfTimers ^{CODESYS Forge talk (Post)}
Hi, these variables are internal members of the axis. They measure the duration of some internal function calls.
Last updated: 2023-11-23

Post by tk096 on Pointer to Softmotion axis ^{CODESYS Forge talk (Post)}
Hi, you can take a look at https://content.helpme-codesys.com/en/CODESYS%20Development%20System/_cds_pragma_attribute_global_init_slot.html Maybe it helps.
Last updated: 2023-11-23

Post by eschwellinger on Hydraulic Axis Controller ^{CODESYS Forge talk (Post)}
I would check this example: "c:\Program Files\CODESYS 3.5.19.X\CODESYS\CODESYS SoftMotion\Examples\Tutorial\PosControl.project"
Last updated: 2023-12-09

Post by eschwellinger on Softmotion axis to CANopen Maxon IDX drive ^{CODESYS Forge talk (Post)}
I would try to use the EDS file of the maxon drive.
Last updated: 2024-01-06

Post by kumareasu on Hydraulic Axis Controller ^{CODESYS Forge talk (Post)}
Hope I need to softmotion package ( https://store.codesys.com/en/codesys-softmotion-axes-4.html ) for this. Please confirm.
Last updated: 2024-02-23

Post by spiessli on Softmotion axis to CANopen Maxon IDX drive ^{CODESYS Forge talk (Post)}
Just verified the behaviour. Still is the same. It should be attached here. But I also tried the DCF-file with the axis in the lab with the real drive: The MC_Power block never goes out of busy. Had not time to investigate further, though.
Last updated: 2024-01-08

Post by florian on Stepper Drive with Ethercat ^{CODESYS Forge talk (Post)}
Codesys has a motion libraries (SoftMotion), but you need to buy a licence keys for them to work. the most basic one is SoftMotionLight. you just have to select your drive in the device view and add a SoftMotionLight CiA402 axis. then the library is added to your project. You can use the SML_* motion FBs and configure the axis now.
Last updated: 2024-03-22

Post by installwhat on Tripod rotary coordinate is not correct with right hand rule ^{CODESYS Forge talk (Post)}
https://www.instructables.com/Work-Coordinate-System/ https://www.researchgate.net/figure/The-WCS-Axis-follows-the-Right-Hand-Rule-Left-Where-the-Z-Axis-Points-Towards-the_fig1_288835535#:~:text=Hwa%20Jen%20Yap-,The%20WCS%20Axis%20follows%20the%20Right%20Hand%20Rule%20(Left)%20Where,tool%20relative%20to%20the%20WCS. https://help.autodesk.com/view/ACDMAC/2025/ENU/?guid=GUID-02A08BCD-B4E5-4068-9932-810EF3049218
Last updated: 2024-06-23

Post by tk096 on gear over gear (2 masters,1 slave) - how to do it? ^{CODESYS Forge talk (Post)}
Hi, you could calculate the position/dynamics of the slave axis yourself and use one of the function blocks SMC_FollowPosition/SMC_FollowSetValues to move the slave axis. https://content.helpme-codesys.com/en/libs/SM3_Basic/Current/SM3_Basic/POUs/Movement/Direct/SMC_FollowPosition.html https://content.helpme-codesys.com/en/libs/SM3_Basic/Current/SM3_Basic/POUs/Movement/Direct/SMC_FollowSetValues.html
Last updated: 2024-08-19

Post by axilleas on SMC_Interpolator + SMC_controAxislbyPos ^{CODESYS Forge talk (Post)}
dear all I am working on a very generic gantry system (virtual drives + win v3 control) reading gcode from external file. In order to stop the interpolator function from running when gaps are detected, SMC_controlAxisByPos FB has the bStopIpo output which according to the manual is connected to the Interpolator's bEmergencyStop. Lets assume that the axis are parked in position X1000 Y1000 and the initial G code movement is G00 X500 Y500. The normal behavior is to travel from the actual x1000 y1000 to G00 X500 Y500. The SMC_Interpolator always gets the X0 Y0 as the initial position, meaning that the bStopIpo is active until the axis are in X0 Y0 and the release the interpolator to set the new positions to X500 Y500. Is there a suggested method to solve this behavior? bonus question: I get a lot of bStopIpo during standard interpolation movements (not gaps). While working with virtual axis this is not a problem but when real axis are installed this will be an issue. What exactly triggers the bStopIpo output? Slow axis accelerations compare to Gcode defaults? Kind Regards
Last updated: 2024-02-05

Post by jonasz on Discontinuity of A/B/C axis movement. ^{CODESYS Forge talk (Post)}
Hi, My problem was related to the behavior of the modulo axis, but maybe you will find something useful from what I write. The solution lies in path processing. Codesys offers a G-code analysis tool. Insert a CNC object into the project. The CNC settings object will be added automatically. By inserting appropriate processing modules into the CNC settings object and parameterizing them, you can test the behavior of the axis. When the effect is satisfactory, remember to add the module from CNC settings in the correct order in the processing path. Each CNC machine case is different. You need to spend some time to get your design tailored like an Armani suit. Good luck.
Last updated: 2024-05-09

Post by esave on Stepper Drive with Ethercat ^{CODESYS Forge talk (Post)}
I bought and installed SoftMotion Light now. When I try to add a SoftMotion Light Axis to my stepper drive and I go online it shows: "The license is missing or invalid". See picture What am I doing wrong? This is the right way right? First add your EtherCat XML-File from your stepper driver and then add the SoftMotion Light axis right? Thanks for your help esave
Last updated: 2024-04-25

Sort by relevance or date