Post by baott569 on Limitation on OPC UA Variable 100+ variables on raspberry pi ^{CODESYS Forge talk (Post)}
Sorry, not trying to spam, My internet lagged and I thought the comment wasn’t submitted
Last updated: 2026-01-22

Post by baott569 on Limitation on OPC UA Variable 100+ variables on raspberry pi ^{CODESYS Forge talk (Post)}
Hi, did you manage to resolve this issue?, I’m experiencing the same problem
Last updated: 2026-01-22

Post by reinier-geers on Network variable stops sending ^{CODESYS Forge talk (Post)}
Thanks. but ive got unique identifiers. and i dont save to a file.
Last updated: 2026-04-28

Post by solidlogicguy on Little endian to Float from Modbus RTU ^{CODESYS Forge talk (Post)}
Hello, I got a device from which I require to read values from I am using a WAGO PLC 750-8212 and I am communicating through Modbus Master FUNCTION BLOCK from library WagoAppPLCModbus in Codesys 3.5 to this device. I already receive data from the device that is a CVM to monitor voltage from a fuel cell. The technical support of the company that makes these devices says that the data is sent in little endian form. And I want to convert it to a float value. The tech support sent me the next instructions of how to do it but I am new using codesys, so any advice or help I will really appreciate so much. Message from tech support: The process is complicated, better to do it with already implemented library in the language/program you use. Basically the process should be next: To convert the two Modbus registers containing parts of a 32-bit float in little-endian byte order to a floating-point number using mathematical operations, you first need to combine the two 16-bit integers (assuming reg1 is the lower word and reg2 is the higher word) and then interpret the result according to the IEEE 754 standard. Given: - Register 192 (reg1) = 4096 - Register 193 (reg2) = 14884 Step 1: Combine the two registers. Since we are dealing with little-endian byte order, reg2 is the high word, and reg1 is the low word: combined = reg2 * 2^16 + reg1 combined = 14884 * 65536 + 4096 combined = 975175680 + 4096 combined = 975179776 Step 2: Convert the combined value to binary: combined_binary = '1110101101011100000000000000000' Step 3: Split the binary into IEEE 754 components: Sign bit (1 bit): 0 Exponent (8 bits): 11101011 Mantissa (23 bits): 01011100000000000000000 Step 4: Convert the binary exponent to decimal and subtract the bias (127 for 32-bit floats): exponent = int('11101011', 2) - 127 exponent = 235 - 127 exponent = 108 Step 5: Calculate the mantissa as a fraction: The mantissa in IEEE 754 format is the fractional part after the leading 1 (which is implicit). Therefore, we need to convert the binary mantissa to decimal and add the implicit leading 1: mantissa_fractional = 1 + int('01011100000000000000000', 2) / 2^23 mantissa_fractional = 1 + 18688 / 8388608 mantissa_fractional = 1 + 0.002227783203125 mantissa_fractional ≈ 1.002227783203125 Step 6: Combine the sign, exponent, and mantissa to get the float value: float_value = (-1)^0 * mantissa_fractional * 2^exponent float_value = 1 * 1.002227783203125 * 2^108 Because the exponent is quite large, the resulting float value is a very large number.
Last updated: 2023-12-15

Post by alexgooi on Licensing info not available. ^{CODESYS Forge talk (Post)}
Sorry for the question, but I'm not completely getting the idea here, could you be more specific, maybe give an example? I'm now in a state where I don't have a softcontainer on my license server anymore (even after reinstalling from the Codesys-IDE). I tried reaching the webserver of Codemeter but when I do that I get redirected to http://"IP":22352 This is not reachable, afterwards I installed lynx on my Debian machine (command line only). From here I could reach the webserver and toggle the network server setting, but unfortunately this did not help. I also tried to changed the remote read setting to 1 (in the Server.ini file). But after a Codemeter reboot this is overwritten to 0. I have the feeling that it should be much easier to get a license to work, am I missing some checkbox somewhere? Is there a tutorial (or manual) that explains the licensing sequence step by step, because I'm pretty stuck.
Last updated: 2025-10-01

Post by gseidel on AXIS_REF_SM3 Error Codes? ^{CODESYS Forge talk (Post)}
Hi SLUCodesys, dwErrorId is a drive specific error number. The drive documentation should be consulted to interpret it. (Note that you should use MC_ReadAxisError to read this error, see https://content.helpme-codesys.com/en/libs/SM3_Basic/Current/SM3_Basic/POUs/Diagnostics/MC_ReadAxisError.html. Accessing the internal variable will result in outdated values if the acis error is not mapped by PDO and is not recommended in general.) uiDriveInterfaceError holds errors of the SoftMotion driver for the drive. It is also an internal variable, not intended for direct access. It is intended for logging, the PLC log will contain the drive interface error, consisting of this number and an error text. My recommendation for handling axis errors in the CODESYS application: 1) Use MC_ReadStatus on the axis to find out whether it is in state Errorstop 2) If in Errorstop, there are two possibilities: an error reported by the drive (MC_ReadAxisError) or an error of the SoftMotion function blocks (output MC_ReadStatus.FBErrorOccured). 3) If there is no drive error, you can use SMC_ReadFBError https://content.helpme-codesys.com/en/libs/SM3_Basic/Current/SM3_Basic/POUs/Diagnostics/FBError/SMC_ReadFBError.html Best regards, Georg
Last updated: 2025-09-24

Post by ilya-vah on Table element issues ^{CODESYS Forge talk (Post)}
Hello, First post here. I would like to clarify whether the following behavior is known or if it is a bugs. Issue 1 — First row not displayed when using Maximum array index with 1-based arrays Description: When displaying data from an array that is indexed starting from 1 (e.g., ARRAY[1..N]), and the number of displayed rows is limited using the Maximum array index property, the first row of the array is not shown in the visualization. Steps to reproduce: Create an array indexed from 1 (e.g., ARRAY[1..N]). Bind the array to a Table element. Limit the number of displayed rows using the Maximum array index property. Run the visualization. Actual result: The first array element (index 1) is not displayed in the table. Issue 2 — Tooltip string placeholder cannot be bound to string variable from array Description: It is not possible to use a string placeholder in the tooltip that is bound to a string variable from the array. Steps to reproduce: Use a table bound to an array containing string variables. Configure a tooltip using a string placeholder referencing a string field from the array. Run the visualization. Actual result: Tooltip doesn't show any text. A test project demonstrating both issues is attached. Thank you for your time and support.
Last updated: 2026-02-16

Post by maxsus on Visu Frame-configuration___text will not work ^{CODESYS Forge talk (Post)}
Hello I have a problem with the Frame-configuration. In the picture below you can see that I set the Editor Type to variable. If it would be text it would work, but it wasnt variable anymore. Thanks for your time. Sorry, my codesys is in German.
Last updated: 2024-08-20

Post by maxsus on Visu Frame-configuration___text will not work ^{CODESYS Forge talk (Post)}
Hello I have a problem with the Frame-configuration. In the picture below you can see that I set the Editor Type to variable. If it would be text it would work, but it wasnt variable anymore. Thanks for your time. Sorry, my codesys is in German.
Last updated: 2024-08-20

Post by worker69 on Alarmgruppenvorlage kann über Kontextmenü keine weitere Latch Variable hinzugefügt werden ^{CODESYS Forge talk (Post)}
Hallo, ich habe das problem, dass ich in einer Alarmgruppenvorlage keine wietere LATCh Variable hinzufügen kann. Wenn ich dies über das Kontextmenü versuche, dann erscheint folgende Fehlermeldung "Der Objektverweis wurde nicht auf eine Objektinstanz festgelegt". Ich verwende Codesys V3.5.19 P0 und 23.5.19 P7 Was mache ich falsch
Last updated: 2026-01-05

Post by reinier-geers on Network variable stops sending ^{CODESYS Forge talk (Post)}
I use network variables. But when i change the programm, it wil stop sending. Then is have to add or delete a variable. Then i will be compiled again and sends again. This problem wasw already in 9.20 but seems to be still in 21.0 . Is there a way to solve this ?
Last updated: 2026-04-20

Reading from a file, a line of CSV values with CrLf at the end of the line. ^{CODESYS Forge talk (Thread)}
Reading from a file, a line of CSV values with CrLf at the end of the line.
Last updated: 2018-09-18

Post by tk096 on Confused by dwIpoTime input for SMC_Interpolator ^{CODESYS Forge talk (Post)}
Hi, dwIpoTime should be set to the cycle time of your motion task. It defines the interpolation interval of the interpolator. E.g. in the attached screenshot, the task has a task interval of 4ms. The dwIpoTime input of the interpolator should be set to 4000.
Last updated: 2024-07-22

Post by timvh on Array of Program ^{CODESYS Forge talk (Post)}
You cannot create an array of Programs. Create a Function Block for this purpose instead of a program. You can create an array of FB instances and call each instance in a loop.
Last updated: 2024-09-03

Post by timvh on Converting each character to a string into ASCII ^{CODESYS Forge talk (Post)}
A standard string is actually a list of bytes that represent the ASCII code for each character. The following part of code will give you the ASCII code of one of the characters in the string: byChar := sInput[i];
Last updated: 2024-11-11

Post by nonstop-cat on Problem of assigning physical addresses to variables of type ARRAY OF ARRAY as MW and QW ^{CODESYS Forge talk (Post)}
Array writing method error,,,<arrayname>: ARRAY [<ll1>..<ul1>, <ll2>..<ul2>, <ll3>..<ul3>]</ul3></ll3></ul2></ll2></ul1></ll1> OF <basedatatype></basedatatype></arrayname>
Last updated: 2025-03-31

Post by nonstop-cat on Problem of assigning physical addresses to variables of type ARRAY OF ARRAY as MW and QW ^{CODESYS Forge talk (Post)}
Array writing method error,,,<arrayname>: ARRAY [<ll1>..<ul1>, <ll2>..<ul2>, <ll3>..<ul3>]</ul3></ll3></ul2></ll2></ul1></ll1> OF <basedatatype></basedatatype></arrayname>
Last updated: 2025-03-31

Is it possible to link an array of bits to an alarm group to show a lot of alarms at once? ^{CODESYS Forge talk (Thread)}
Is it possible to link an array of bits to an alarm group to show a lot of alarms at once?
Last updated: 2021-07-08

Size of the abyPoolMemory input when creating an fb for the purpose of fb creation (fb extends Factorybase from the fbFactory Library) ^{CODESYS Forge talk (Thread)}
Size of the abyPoolMemory input when creating an fb for the purpose of fb creation (fb extends Factorybase from the fbFactory Library)
Last updated: 2023-01-15

How to change list of referenced visualizations of a frame by programm? (NOT how to switch vis!) ^{CODESYS Forge talk (Thread)}
How to change list of referenced visualizations of a frame by programm? (NOT how to switch vis!)
Last updated: 2023-06-01

Codesys Forge Unit Testing Framework [Announcement of the new CfUnit release: v1.1.0.0 ETA 1st quarter of 2020] ^{CODESYS Forge talk (Thread)}
Codesys Forge Unit Testing Framework [Announcement of the new CfUnit release: v1.1.0.0 ETA 1st quarter of 2020]
Last updated: 2019-06-16

Codesys Forge Unit Testing Framework [Announcement of the new CfUnit release: v1.1.0.0 ETA 1st quarter of 2020] ^{CODESYS Forge talk (Thread)}
Codesys Forge Unit Testing Framework [Announcement of the new CfUnit release: v1.1.0.0 ETA 1st quarter of 2020]
Last updated: 2019-06-16

Post by jeffyech on <Dereference of invalid pointer> ^{CODESYS Forge talk (Post)}
I have a program which calls a structure. while online with the PLC, I get: <dereference of="" invalid="" pointer=""> in the declaration values area. What are the causes of this? Can it be solved?</dereference> Version 3.5 of codesys.
Last updated: 2026-06-25

The element of type 'VisuFbElemImage' could not be updated. Reason: Index was outside the bounds of the array. ^{CODESYS Forge talk (Thread)}
The element of type 'VisuFbElemImage' could not be updated. Reason: Index was outside the bounds of the array.
Last updated: 2026-01-27

Post by arundara on Variable Sync Issue In Soft Plc Redundancy ^{CODESYS Forge talk (Post)}
Hello, I was trying to create a redundancy POC for our application where we read data from few modbus tcp devices. As there is a limitaion that modbus tcp device support only for single master device, we wanted to test how the variable sync happens in redundancy mode. For that i have used the redundancy sample code added a variable "b" under a condition. What i observed was while active controller is running, if passive controller is powerup, passive controller is able to sync all the data configured for redundacny. But after that the variable data which resided under a condition is not synching from active to passive controller. I have attached the image where i have highlighter the variable. Can some help me to understand how redundacny work in codesys soft plc and if there is a solution to sync variable which are under condition, please explain the same or suggestion to achieve the same. Hardware - Raspberry Pi (2 qty) Redundancy licence used - yes in both controllers. Codesys runtime - 4.9.0.0 Codesys software version - V3.5 SP19 if i have posted this question in wrong section, please do let me know in whcih section i have to post this question.
Last updated: 2023-12-01

Sort by relevance or date