Post by tk096 on High Cycle Times for SoftMotion_PlanningTask when using AxisGroup ^{CODESYS Forge talk (Post)}
Hi, under this circumstances the performance of a Raspberry Pi 4 should be sufficient to run a Softmotion robotics application. A closer look at the project would be required. Maybe you could contact the codesys support? Usually it is recommended to run the planning task cyclically every 2ms with task priority of 0 on a dedicated core. In the task configuration you can have a look at the average and maximum execution time of the planning task. You could use the function block SMC_TuneCPKernel (https://content.helpme-codesys.com/en/libs/SM3_Robotics/Current/SM3_Robotics/POUs/AdministrativeConfiguration/Computation/SMC_TuneCPKernel.html) to define suitable values for the parameters 'fSyncBufferDuration' and 'fPlanningInterval'. However, as previously mentioned, the performance of a Raspberry Pi 4 with realtime patch should be sufficient. The 'fPlanningInterval' parameter specifies the maximum planning step width in seconds. The cycle time of the planning task should not permanently exceed this value. A higher value reduces the computational effort, but can lead to a violation or no full utilization of the set limit values for velocity, acceleration and jerk. From a starting value of 0.016 seconds, the value should be increased gradually until the performance is acceptable. The parameter 'fSyncBufferDuration' specifies the size (in seconds) of the buffer between the planning and fieldbus task. The cycle time of the planning task must not exceed this value at peak times (this will lead to the error SMC_CP_QUEUE_UNDERRUN). A higher value can compensate for peaks in the cycle time of the planning task. At the same time, however, this also increases the latency for executing interrupts and aborting movements.
Last updated: 2024-03-22

Post by macros8 on Alarm Management - latched variable represented as Text list ^{CODESYS Forge talk (Post)}
Hi all, in Alarm management you can latch some variable to show value within the alarm msg. It´s very useful sometime. But I´m wondering whether there is any possibility to represent that value as Text list. It´s quite common in other HMI tools and this is very useful in case of using some ErrorID for detail specification of error. Unfortunately I could not find any way how to do it but I believe that exists :) Thanks a lot. M.
Last updated: 2023-09-06

Post by wiresplus on INT_TO_WORD function not working ^{CODESYS Forge talk (Post)}
Hello, I need to take an INT input, and convert it to a WORD value. VAR DRV2Speed : WORD; //IO card takes a WORD where 16000 = full 10V output (equivalent to 50Hz) PumpFillSpeed : INT; //Users enter a value between 0 and 50 END_VAR IF <conditions> THEN DRV2Speed :=INT_TO_WORD((PumpFillSpeed/50)*16000); END_IF </conditions> According to me this should work - but it stays at 0, no matter what. What am I doing wrong?
Last updated: 2024-01-26

Post by umair on Code for reading 4 address to get 1 value of sensor (Ethernet IP) ^{CODESYS Forge talk (Post)}
Hi all, I want to ask, how do I write code to read multiple address for Ethernet IP communication protocol? Because this multiple address will produce one reading of a sensor that I am currently using. I want to read the value of the sensor. https://global.discourse-cdn.com/business6/uploads/wago/original/1X/7a79f4ad7ce474b9383b8550356d984defd9f3a0.png The addresses are in Byte. The 4 addresses are 89,90,91,92. Thanks in advance. Best regards, Umair
Last updated: 2024-05-06

Post by fless on FB having single input but initialized with Array ^{CODESYS Forge talk (Post)}
Why will it retain the sum value from the last call? This is how PLC work. Usually variables only get initialized after a download or a reset (i.e. power loss). RETAIN variables are saved in a special kind of RAM and keep their value after a power loss. To initialize variables on every call of your FB use the VAR TEMP block. VAR_TEMP sum : INT; END_VAR
Last updated: 2024-05-07

Post by wiresplus on Display minutes as hours & minutes ^{CODESYS Forge talk (Post)}
Hello, I have a counter that increments an INT value once per minute I want to display this value in Minutes until 60, then Hours/Minutes thereafter on the HMI Codesys V3.5 SP16 I can divide the minutes by 60 to get hours, but then the minutes is still more than 60. Example: a process has run for 350 Minutes. I need to display "5 Hours 50 Minutes" But if it's only been 45 Minutes, I don't want "0 Hours 45 Minutes" , just "45 Minutes"
Last updated: 2024-05-25

Post by shawn-plc on Return value from a tag given a string literal ^{CODESYS Forge talk (Post)}
Good afternoon everyone, I am looking for a way to return a value given a string tag path. I put together a pseudo-example to illustrate my use-case and was wondering if anyone in this forum can help. The function fnValueFromTagPath is the function I am looking to either create or use from existing library. I would greatly appreciate it. Please see the attachment for additional detail. -Shawn
Last updated: 2024-08-13

Post by taqamert on IFM-Sensor ADC READ ^{CODESYS Forge talk (Post)}
I have a pressure sensor that measures 0-600 bar and outputs a 0-5V signal, but my PLC reads analog inputs in the 0-10V range and displays a value of 1024 when 10V is applied. In this case, when the sensor outputs 5V at 600 bar, the PLC shows a value of 512. My working range is 0-350 bar, which means the PLC only uses 298 bits in this range, significantly reducing the resolution. What can I do to achieve better resolution within the 0-350 bar range?
Last updated: 2024-08-23

Post by taqamert on IFM-Sensor ADC READ ^{CODESYS Forge talk (Post)}
I have a pressure sensor that measures 0-600 bar and outputs a 0-5V signal, but my PLC reads analog inputs in the 0-10V range and displays a value of 1024 when 10V is applied. In this case, when the sensor outputs 5V at 600 bar, the PLC shows a value of 512. My working range is 0-350 bar, which means the PLC only uses 298 bits in this range, significantly reducing the resolution. What can I do to achieve better resolution within the 0-350 bar range?
Last updated: 2024-08-23

Post by taqamert on IFM-Sensor ADC READ ^{CODESYS Forge talk (Post)}
I have a pressure sensor that measures 0-600 bar and outputs a 0-5V signal, but my PLC reads analog inputs in the 0-10V range and displays a value of 1024 when 10V is applied. In this case, when the sensor outputs 5V at 600 bar, the PLC shows a value of 512. My working range is 0-350 bar, which means the PLC only uses 298 bits in this range, significantly reducing the resolution. What can I do to achieve better resolution within the 0-350 bar range?
Last updated: 2024-08-23

Post by balazska2 on Position values with integer variables ^{CODESYS Forge talk (Post)}
Hello guys! https://content.helpme-codesys.com/en/CODESYS%20Visualization/_visu_elem_label.html My question: Could I give an integer variable to the Position records (in the Element list => Position => width / height)? If yes, how? I defined a TEST integer variable with 300 value. I tried to add this variable to the width record (.TEST or only TEST), but if I saved, the value jumps back to 0. Thanks for your help! :)
Last updated: 2024-10-03

Post by dogulas on OPC UA C# client connecting to OPC UA CODESYS server ^{CODESYS Forge talk (Post)}
Ok, for the sake of completeness in case anyone else has this problem. I can tell you that what finally worked for me was to change the line: // create an ExtensionObject to wrap the value to be written ExtensionObject extensionObject = new ExtensionObject( new ExpandedNodeId("GVL_StructA", 5), structAData ); to: // create an ExtensionObject to wrap the value to be written ExtensionObject extensionObject = new ExtensionObject( new ExpandedNodeId("GVL_StructA|defaultbinary", 5), structAData ); I'm sure there are many other problems that could cause this very generic error, but this was my problem.
Last updated: 2024-12-30

Post by mondinmr on Something of strange in the trace ^{CODESYS Forge talk (Post)}
I noticed something strange in the trace: one of the variables (specifically parts.servoFeeder.m_pathGen.m_acPos) is showing an absurd or unrealistic value—something around 4E+18. However, when I check the same variable in the watch window, it shows a normal and expected value (around 506). Do you know why there is this discrepancy between the trace and the watch? Could it be a bug in the trace tool? Thanks in advance!
Last updated: 2025-05-16

Post by maralani on Retain memory change to ZERO ^{CODESYS Forge talk (Post)}
Hi, thanks for help, I add some retain variable , then some other variable change to zero , andI was not able to change the value
Last updated: 2023-09-19

Post by i-campbell on Official MQTT-Client: MAX_RECEIVE_BUFFER_SIZE_EXCEEDED ^{CODESYS Forge talk (Post)}
256MB for the protocol yes, but the default value for this library parameter limits the library to 6kB per task scan.
Last updated: 2023-09-27

Post by ton on How to create a stopwatch? ^{CODESYS Forge talk (Post)}
Hi, i guess you want to make a hour counter. You need to store the measured value. Try to use a retain variable, but need a graceful shutdown, or save it your self. see https://forge.codesys.com/forge/talk/Runtime/thread/278e325579/ Succes.
Last updated: 2023-12-12

Post by open on How to create a stopwatch? ^{CODESYS Forge talk (Post)}
Thanks everyone for your input, I am using persistent variables to retain the timer value after machine shutdown, and main task to be as low as possible for the seconds TON to be accurate.
Last updated: 2023-12-14

Post by dkugler on Ramp function ^{CODESYS Forge talk (Post)}
The util.RAMP_INT and util.RAMP_REAL from Codesys have an input for the start value. What is the advantage of this OSCAT ramp instead of the Codesys util lib?
Last updated: 2024-01-10

Post by dim54 on MBChannel ^{CODESYS Forge talk (Post)}
Hello! I am interested in the Modbus Slave channel parameter uiReadLength to use in the ST-program (see picture). How to read the value of uiReadLength in a ST-program? Only Edwin the Great and Terrible can answer this question.
Last updated: 2024-01-22

Post by irshad on Modbus TCP/IP slave communication errow ^{CODESYS Forge talk (Post)}
While reading the value of a slave device, it shows error frequently and i need to restart my PLC for getting the communication back. In codesys it shows the slave in Red color with error status. How to solve the above
Last updated: 2024-02-03

Post by timvh on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
You should only open de COM port once and then leave it open. This hCom should not keep on incrementing. (off course when you are done communicating, you need to close the COM port)
Last updated: 2024-03-22

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Sort by relevance or date