Post by jens on Modbus tcp - channel ^{CODESYS Forge talk (Post)}
Help wanted This is the first time i'm doing a Modbus Tcp project. I have some VLT with a extension module MCA-122. i'm currently unable to write to the VLT slave, but i can read from status word parameter=1603 and address := 16029 where the address is calculated from parameter is ((id x 10)-1). in the manual the functions that are supported are 3 hex, 6 hex, 10 hex, b hex and 11 hex. read holdin registers, write single register, write multiple registers, get comm. event counter, report slave id. i'm only using the Modbus Slave Channel is this wrong when trying to write to the vlt ?
Last updated: 2024-06-13

Post by thewizard8 on Raspberry PI4 Serial Port ^{CODESYS Forge talk (Post)}
Hi Dear All, I'm using my raspberry PI4 as a CoDeSyS PLC (Build from scratch with custom electronics). I was able to implement all fieldbuses with the exception of Modbus Serial. I'm using the internal Port (GPIO) and I configured it in /etc/Codesyscontrol_user.cfg the following away: [SysCom] Linux.Devicefile.1=/dev/ttyUSB0 Linux.Devicefile.2=/dev/ttyS0 I'm using COM2 on Master configuration. I'm using a interface board from TTL/RS485 (bidirectional board), and it's works perfectly with other devices but not in CoDeSyS. I'm able to send data with python script and read it on my pc using putty, but when I use a modbus slave simulator to interface with codesys I always get red icons on master and slave. (Please find image attached). I'm pretty shure that this might be a bad parameter on my CoDeSyS runtime configurstion file. Can someone help me? I'm stuck and this is for my master degree certification.
Last updated: 2024-03-18

Post by lsislsis on SIGABRT Error ^{CODESYS Forge talk (Post)}
2024-11-08T13:39:07.354Z, 0x00000103, 65544, 1, 0, runtime received SIGABRT - system may be in an inconsistent state* We recommend a reboot of the controller now! 2024-11-08T13:39:07.354Z, 0x00000111, 8, 260, 3, #### Exception: More than 2 exceptions in CH_COMM_CYCLE: Stop logging 2024-11-08T14:36:33.126Z, 0x0000100d, 1, 0, 0, Demo mode expired. 2024-11-08T15:35:49.253Z, 0x00000103, 65544, 1, 0, runtime received SIGABRT - system may be in an inconsistent state We recommend a reboot of the controller now! 2024-11-08T15:42:54.664Z, 0x00000103, 65544, 1, 0, runtime received SIGABRT - system may be in an inconsistent state We recommend a reboot of the controller now! *
Last updated: 2024-11-08

Post by markus-huber on CodeSys SVN doesn't work ^{CODESYS Forge talk (Post)}
I installed CodeSys V3.5 SP9 for HY-eVision2 1.18.0.0 and activated the License Keys for SVN and noticed that the "SVN" doesn't pop up when i go on Menu - Project. For some reason the SVN works on CodeSys SP10. I already deinstalled all CodeSys Applications and installed them again but it's the same. Maybe the problem already occurred and someone could help me.
Last updated: 2024-02-20

Post by davidbo on Toradex and CODESYS and licensing ^{CODESYS Forge talk (Post)}
I am evaluating a Toradex product for use with CODESYS. Toradex and CODESYS are partners, but using "CODESYS Virtual Control for Linux ARM64 SL" together with a carrier board "Verdin mallow" However it doesn't seem to be a soft container for licenses. So how do I install a license
Last updated: 2025-10-20

Post by konstantin on Lenze i950 Servo and WAGO PFC200 ^{CODESYS Forge talk (Post)}
Hello, In our workshop we have a Lenze i950 servo drive that has an EtherCAT bus and CiA402 compatibility. The WAGO is PFC200 750-8212 and as per documentation it has built-in license for SoftMotion Light functionality. It is not capable of supporting the full SoftMotion functionality like gearing and synchronizing. I added the EtherCAT esi files from Lenze and the EtherCAT master does see the drive, then I added a SoftMotion Light Axis object. The problem is that I can only energize the axis, I cannot execute any other commands. I set the positive and negative torque limits from the PDOs to 200% and when I try to move the axis by force it does not move back to its original position. I use the SML function blocks from the PLCOpen library and the error from the function blocks is that the op mode cannot be changed. Then I tried using a standard SoftMotion axis object and everything works fine, except the MC_Home function block. The axis moves back to its position when forced out of it. I follow this guide from Lenze - Lenze i950 CODESYS V3 What could cause this issue with the SoftMotion Light axis object? Best Regards Konstantin Kolev
Last updated: 2026-02-11

Post by em1681 on Modbus RTU over 750-652 ^{CODESYS Forge talk (Post)}
Hi, It's my first time operating in Codesys 2.3, but I have done a good amount of Codesys programming, so I'm a little familiar. I haven't done a lot of RTU, but a lot of Modbus TCP. I don't have the PLC in my reach at the moment, but I'm trying to be a little ahead. We're adding the 750-652 module to read energy from a flowmeter over RTU. There will only be 1 slave. I attached pictures of my current hardware, PLC code, the register datasheet from the slave and the only modbus serial library I seem to have available. I'm uncertain if this will work. Any help or clarification on how things work will be greatly appreciated. Thanks in advance.
Last updated: 2025-09-01

Post by bfunk on Wago 750-8101 (mit Codesys V3) als Profinet device ^{CODESYS Forge talk (Post)}
Moin, ich habe da ein Problem und komme einfach nicht weiter... Ich moechte eine Wago 750-8101 (mit Codesys V3) zu einem ModBus TCP Slave und einem Profinet slave machen. ModBus habe ich hinbekommen, Profinet bekomme ich einfach nicht hin. habt ihr das evtl. einen hilfreichen Tip fuer mich? Programmiert wird mit Codesys V3.5 SP19 Patch 2 Auf dem Zielsystem (PFC100) ist die Zielsystemversion 4.6.0.0 Das es nicht optimal ist PN und ModBus TCP auf einer Schnittstelle zu haben ist mir bewusst. Wollte aber erstmal ModBus und Profinet zum laufen bekommen bevor ich das Profinet auf die 2. Ethernet-Schnittstelle bringe. /etc/CODESYSControl_User.cfg [SysSocket] Adapter.0.Name="br0" Adapter.0.EnableSetIpAndMask=1 Adapter.1.Name="br1" Adapter.1.EnableSetIpAndMask=1 ist eingetragen. so sieht der Status fuer das PN-device aus. Anbei ein Screenshot.
Last updated: 2024-01-16

CODESYS ^{CODESYS Forge talk (Thread)}
CODESYS
Last updated: 2017-03-07

Codesys ^{CODESYS Forge talk (Thread)}
Codesys
Last updated: 2024-01-14

Post by hackehucke on Mithilfe von SysSocket eine Verbindung herstellen ^{CODESYS Forge talk (Post)}
Hallo zusammen, vorweg: ich habe sehr sehr wenig Ahnung von Codesys, industrieller Kommunikation etc ... Ich soll für ein Seminar mithilfe der Library SysSocket eine HTTP Verbindung zwischen PC und und der Wago PFC200 herstellen, die wir hier im Labor haben. Ich habe mir unterschiedliche Examples von Codesys angeschaut, ChatGPT gepromptet etc. aber komme nicht in die Nähe von irgendwas, das funktioniert. Kann mir jemand ganz einsteigerfreundlich erklären, welche Bausteine ich benötige und was mit diesen getan werden müsste, um das ganze zum laufen zu bekommen? Wäre auf ewig dankbar ... Verzweifle hier langsam :( Viele Grüße
Last updated: 2026-01-07

Post by sebastian-hk on Codesys auf einen Cortex M4 lauffähig machen ^{CODESYS Forge talk (Post)}
Hallo, wir spielen mit dem Gedanken, Codesys auf einen AT SAM E54 Xplained Pro lauffähig zu machen. dieser besitzt einen Atmel ATSAME54P20A mit einem Cortex M4. Meine Fragen hierbei: Was muss portiert werden, wenn die Zielhardware momentan noch nicht unterstützt wird? Gibt es ggf. Anleitungen, um die Laufzeit auf solch einen Controller zu bringen? Muss hierbei ein eigener Interpreter entwickelt werden, der den compilierten Code "übersetzt"? Wie lauffähig ist der rübergespielte Code, gibt es irgendwelche Einschränkungen bei der Programmierung in Codesys? (Verwendung von bestimmten Datentypen nicht möglich?) Was für Lizenzen werden für den Controller benötigt? Vielen Dank im Voraus Sebastian
Last updated: 2024-01-03

Post by rd76065 on Opto 22 Groov PR2 Modbus TCP Master communication ^{CODESYS Forge talk (Post)}
Previously, I have used ModbusEthernet_04 library for Wago for ModbusTCP Master communicational in Codesys V2.3. How to use same communication of similar UDT for Opto22 Groov PR2 PLC in Codesys V3.5 SP20. Can I use OSCAT library - Network -MB_Client or IODrvModbusTCP - ModbusRequest for this requirement? If any other please guide.
Last updated: 2024-05-31

Post by charleskentyfz on (no subject) ^{CODESYS Forge talk (Post)}
I have created an EtherCAT slave code and fixed two slaves (IDs written in the 0xF050 object dictionary). The module IDs are 0x1 and 0x101, respectively. It can be scanned normally in TwinCAT, but when scanning in CODESYS, it reports an error. Why is this happening？text in the second pic means 'device cannot be found in repository'
Last updated: 2024-07-07

Post by bolopg on MODBUS TCP REGISTERS CODESYS V3.5 ^{CODESYS Forge talk (Post)}
Hi. I have a problem with MODBUS TCP MASTER. I treid to read HR in range 3027-3037 but I cannot read them. I have modbus slave chanel with offset 0x3037. I checked what I read and it looks like I am reading HR in range 1-10. What I am doing wrong.
Last updated: 2024-10-11

codesys v3 2 codesys v2 ^{CODESYS Forge talk (Thread)}
codesys v3 2 codesys v2
Last updated: 2014-08-04

Post by eschwellinger on Beispieldateien finden / Inhalt der Packages ^{CODESYS Forge talk (Post)}
ja danke hilft definitv & sorry- das wird verbessert, künftig werden die Packages & Beispiele nach "c:\Program Files\CODESYS <version>\CODESYS\CODESYS Control for Raspberry PI\<version>\Examples\" installiert werden.</version></version> Beispiel für die PI Beispiele: "c:\Program Files\CODESYS 3.5.19.30\CODESYS\CODESYS Control for Raspberry PI\4.10.0.0\Examples\" dass wird für alle Aktualisierungen/Updates der Packages so ausgerollt.
Last updated: 2023-11-17

Post by reinier-geers on API webclient ^{CODESYS Forge talk (Post)}
Fur ein jahr ein webclient lisence gekauft. Aber immer funktioniert es noch nich. Mach ik es auf internet bekomme ich daten. Aber mit codesys bekomme ich - Query fehler ... - ein switch die abschalt - oder den controller hangt mal wieder Hat eine dar erfahrung? Kan ich in den FB sehen was da pasiert ?
Last updated: 2026-04-05

Post by muhq on Profinet connection to Siemens CP343-1 Lean (IO-Device/Slave) ^{CODESYS Forge talk (Post)}
Hi, I am quite new to Codesys and I try to do a Profinet connection to an Siemens PLC (315-2DP) with CP343-1 Lean Modul. I already configured the Siemens PLC, exported the GSDML. Then I added a new project in Codesys, added following moduls: - Ethernet - PN_Controller - Imported Profinet Device via GSDML importer When I start the programm everything looks fine but I always get the message "Stopped Profinet" and no data is available This is only for a small test. Therefore I start to do that on a Windows 10 with Development System. Later I will try to realize this on Raspberry. Ethernet Adapter is configured (192.168.1.1 / 24) Firewall deactivated WinPCap is installed S7-Station seems to be found ('fuadazenzitest') Can please somebody help me?
Last updated: 2023-08-26

Post by rajatdas2005 on Codesys Virtual control SL ^{CODESYS Forge talk (Post)}
Hi, Thank you for your reply. 1. Codesys IDE version is it showing 3.5 SP 20. please check the attachment. 2. Codesys Virtual control for SL -- version is 4.16
Last updated: 2025-08-07

Post by eschwellinger on Stepper motor control with (SM_Drive_RaspStepper_direct) ^{CODESYS Forge talk (Post)}
.. try to use this projectarchive for the Stepper. In case you search for SoftMotion Examples: "c:\Program Files\CODESYS 3.5.21.X\CODESYS\CODESYS SoftMotion\Examples\Tutorial\"
Last updated: 2025-11-11

Post by sigurdrb on Codesys and error messages, warnings exceptions etc. ^{CODESYS Forge talk (Post)}
Hi, I tried some different libraries (CmpApp etc.) to find some global variables that I could read out as a variable in the codesys environment. Do any one of you know which libraries are best suited for this, and how I can read it out? My goal is to send messages, warnings etc. to the system that communicates to the PLC. Currently if something goes wrong I need to see the logfiles, or go online with the controller. I think I could save a lot of time if I could read the errors from our user interface that is connected to the PLC by TCP/IP.
Last updated: 2024-11-06

Post by ewi04 on How to upload application file to remote controller (offline) ? ^{CODESYS Forge talk (Post)}
Hi, I am looking for a good way to update a decice remotely. The devices are distributed worldwide and have normally no connection to the internet. The CODESYS Automation Server can't help here. So I want to update the decices via USB stick. I have written my own code* to update the files that are created with ‘Create boot application’. But sometimes strange things happen: visu elements are present, but are not found the application is no longer registered and therefore no longer starts I have not yet found out why these errors occur. Has anyone had similar problems or found a better way? Is there perhaps a CODESYS library or something else? Many thanks! *the code deletes the directories on the device and copies the new directories from the USB stick while the system is running (goes without saying)
Last updated: 2024-02-05

Post by edvard-munch on How I can get "Done flag" for "Modbus Slave Channel"? ^{CODESYS Forge talk (Post)}
This is from 10 years ago, I know. But I have been using (SLAVE_DEVICE.iChannelIndex = CHANNEL_NUMBER) AND (SLAVE_DEVICE.xDone) I suppose that it shows xDone for the channel that shows up in the iChannelIndex at the same cycle? It seems to be working properly for two devices that I have been using it before But now I have another device and using two write channels, for one register each. One channel works properly and returns DONE flag When another channel is triggered, I see that it shows up in iChannelIndex, but flag DONE not received, but no Error for the channel. Also, when i check the register in the device it's evident that data has been transferred. Is this could happen sometimes with CODESYS, so DONE flag not received? Or this is a problem with a given device? With this certain register
Last updated: 2024-12-19

Post by cer-wa on Not able to connect multiple profinet encoder in codesys Linux ARM64 ^{CODESYS Forge talk (Post)}
Hello, currently im working with a RevPi connect 5 on a codesys project. Up until now I was having a blast because things were going really smooth but for like almost a day im kind of stuck on the integration of multiple profinet sensors into my project. This is kind of a bummer because that should be an easy thing to do. What I tried so far was to create and additional ethernet adapter where I then tried to connect my devices. in the beginning I tried to connect the devices directly which was not working because I could assign the IP-adress only to the ethernet adapter and not to the devices but the device was found in the device repository (this gets important in the second part) So what I tried next was to setup a PN-Controller and connect my devices subsequently to the Controller. Sadly now the devices wont show up in the device repository anymore. To me its not clear why this is happening. And the worst thing is: I went ahead and setup a device completely like I would want to have it in the project and when I then click on scan devices I can even find the device. But it can not be added to project for whatever reason eventhough im 100% certain that the gsdml file is the correct one. Can anyone help me with this. Like I said this seems like an easy thing to do and its taking me way longer than expected already. The only thing that came to my mind why this might not work is because I have codesys license which only allows one profinet instance. Could that be the case? The error message seems then pretty unfit but ok. I will be grateful for every advice. Thanks in advance! Best regards!
Last updated: 2025-09-25

Sort by relevance or date