Post by gseidel on CAM Motion Recover after STO ^{CODESYS Forge talk (Post)}
Dear Mr. Kolev, I'm not sure I understood correctly. But this is my take on your question: When the STO of the slave is triggered, store the current master position (e.g. 225 units) After the reset of the slave error, call MC_SetPosition on the virtual master and reset it to the stored position (225 units) Optionally, before MC_CamIn is restartet, move the slave back to the slave position corresponding to the stored master position. (If you do this, no ramping in will be necessary) Restart MC_CamIn, with absolute master position and absolute slave position. Choose the StartMode that is appropriate for your machine. Best regards, Georg Seidel
Last updated: 2026-02-16

Post by reinier-geers on Power off bit to save last log ^{CODESYS Forge talk (Post)}
3.5.20.4 Is there a power off bit, so i can save my last logfile ?
Last updated: 2026-02-17

Post by pernockham on Unable to deploy "Control for Linux SL 4.18.0.0" ^{CODESYS Forge talk (Post)}
Correct, my Device architecture says "None" is this position. A missing config somewhere?
Last updated: 2026-02-18

Post by yannickasselin on Question about Demo License limitations for Modbus TCP communication and Fieldbus Instances ^{CODESYS Forge talk (Post)}
As far as I know, there is no other limitations than the 2 hours limit. The demo mode should be plenty enough for testing purposes. Regarding instances. In the device tree, 1 master = 1 instance, no matter how many slaves the master is communicating with. But it is also possible that your Codesys runtime act as a slave. In this case, each slave in the device tree is one instance. You can also use the license metric tool in the IDE. This will tell you exactly how many instances you have in your project. https://content.helpme-codesys.com/en/CODESYS%20Development%20System/_cds_edt_device_licensed_software_metrics.html
Last updated: 2026-02-28

Post by poliautomacao on Absolute movement controlled by an external encoder. ^{CODESYS Forge talk (Post)}
Hello, I made this configuration, I'm moving the encoder value to SM_Driver_PosControl.in.wActPosition. When I make the absolute movement of my PosControl axis, my physical drive axis rotates perfectly, but I noticed that the movement is not followed by the encoder. That is, if I hold the encoder and keep it in position 0, the PosControl axis makes the absolute movement of 314 mm and stops, which is strange because the encoder is at 0. Theoretically, the PosControl axis should accelerate to try to compensate for the movement error. I haven't yet achieved perfect functionality.
Last updated: 2026-03-24

Post by husarz17 on How change Unity-ID in TCP Modbus Slave ^{CODESYS Forge talk (Post)}
My codesys is 3.5.21.30. I am using function ModbusServer from library ModbusTCP_Slave. The reason is that I need share 9000 Holding registers. By standard configuration it is only 4096. fbMbTcpDevice: ModbusTCP_Slave.ModbusServer; fbMbTcpDevice( wPort := 502, pInputData := ADR(awInputReg), pOutputData := ADR(awHoldingReg), uiInputDataSize := 10, uiOutputDataSize := 9000, xEnable := TRUE, tTimeout := 10000, InterfaceName := "eth0", xBusy => xBusy, xError => xError, byClientConnections => byConnections ); Ethernet port is cofigured: Network interface: eth0 IP address: 10.10.22.55 Subnet maskL 255.255.255.0 Default gateway: 0.0.0.0 And it only works when I am reading registers with ID 255 by Modbus Poll. Any other IDs don't work. The actual TCP client device try to read registers with ID 1 and I can't change it... Thanks in advance for your help!
Last updated: 2026-04-01

Post by alexgooi on Network variable stops sending ^{CODESYS Forge talk (Post)}
Hi Reinier, What usually works for me is settings it up in the following way: In the sender block make sure that the list identifier is unique for the whole installation (this is only relevant when you have multiple senders in 1 network). When you are linking the NVL to a file make sure that the path to this file doesn't change. In my experience the NVL stops working when you change the working directory and afterwards open the NVL in de Codesys IDE. If this doesn’t apply to you application, you could also try to change the port number, maybe there is an other process making use of port 1202. Kind regards Alex
Last updated: 2026-04-22

Post by husarz17 on Pi as Modbus TCP slave. Errors ^{CODESYS Forge talk (Post)}
Hi, I have similar issue. Is that possible to use more than 4096 registers with Modbus RTU slave?
Last updated: 2026-04-29

Post by baotthitawat on Cloud SCADA for Industrial Energy Monitoring ^{CODESYS Forge talk (Post)}
Recently I’ve been exploring ATSCADA iEnergy Tools for SCADA-based energy monitoring systems. One thing I find interesting is how modern SCADA platforms are evolving beyond traditional machine monitoring. Many industrial systems are now using Cloud SCADA architectures for centralized energy management, remote dashboards, and operational analytics. ATSCADA iEnergy Tools supports: Real-time energy monitoring Historical data logging MySQL integration Reporting and Excel export Remote SCADA dashboards Cloud-based monitoring systems I think this type of solution is practical for factories, power monitoring applications, building management systems, and other industrial automation projects where energy optimization is becoming increasingly important. Industrial automation is clearly moving toward web-based and cloud-connected SCADA platforms, especially as more facilities focus on digital transformation and smarter energy management
Last updated: 2026-05-26

Post by baotthitawat on Cloud SCADA for Industrial Energy Monitoring ^{CODESYS Forge talk (Post)}
Recently I’ve been exploring ATSCADA iEnergy Tools for SCADA-based energy monitoring systems. One thing I find interesting is how modern SCADA platforms are evolving beyond traditional machine monitoring. Many industrial systems are now using Cloud SCADA architectures for centralized energy management, remote dashboards, and operational analytics. ATSCADA iEnergy Tools supports: Real-time energy monitoring Historical data logging MySQL integration Reporting and Excel export Remote SCADA dashboards Cloud-based monitoring systems I think this type of solution is practical for factories, power monitoring applications, building management systems, and other industrial automation projects where energy optimization is becoming increasingly important. Industrial automation is clearly moving toward web-based and cloud-connected SCADA platforms, especially as more facilities focus on digital transformation and smarter energy management
Last updated: 2026-05-26

Post by fabiodasilveira on Dynamic Setting IP Address from IEC code ^{CODESYS Forge talk (Post)}
It is a shame that it does not work with Eaton XC303 PLCs :(
Last updated: 3 days ago

Post by solidlogicguy on Little endian to Float from Modbus RTU ^{CODESYS Forge talk (Post)}
Hello, I got a device from which I require to read values from I am using a WAGO PLC 750-8212 and I am communicating through Modbus Master FUNCTION BLOCK from library WagoAppPLCModbus in Codesys 3.5 to this device. I already receive data from the device that is a CVM to monitor voltage from a fuel cell. The technical support of the company that makes these devices says that the data is sent in little endian form. And I want to convert it to a float value. The tech support sent me the next instructions of how to do it but I am new using codesys, so any advice or help I will really appreciate so much. Message from tech support: The process is complicated, better to do it with already implemented library in the language/program you use. Basically the process should be next: To convert the two Modbus registers containing parts of a 32-bit float in little-endian byte order to a floating-point number using mathematical operations, you first need to combine the two 16-bit integers (assuming reg1 is the lower word and reg2 is the higher word) and then interpret the result according to the IEEE 754 standard. Given: - Register 192 (reg1) = 4096 - Register 193 (reg2) = 14884 Step 1: Combine the two registers. Since we are dealing with little-endian byte order, reg2 is the high word, and reg1 is the low word: combined = reg2 * 2^16 + reg1 combined = 14884 * 65536 + 4096 combined = 975175680 + 4096 combined = 975179776 Step 2: Convert the combined value to binary: combined_binary = '1110101101011100000000000000000' Step 3: Split the binary into IEEE 754 components: Sign bit (1 bit): 0 Exponent (8 bits): 11101011 Mantissa (23 bits): 01011100000000000000000 Step 4: Convert the binary exponent to decimal and subtract the bias (127 for 32-bit floats): exponent = int('11101011', 2) - 127 exponent = 235 - 127 exponent = 108 Step 5: Calculate the mantissa as a fraction: The mantissa in IEEE 754 format is the fractional part after the leading 1 (which is implicit). Therefore, we need to convert the binary mantissa to decimal and add the implicit leading 1: mantissa_fractional = 1 + int('01011100000000000000000', 2) / 2^23 mantissa_fractional = 1 + 18688 / 8388608 mantissa_fractional = 1 + 0.002227783203125 mantissa_fractional ≈ 1.002227783203125 Step 6: Combine the sign, exponent, and mantissa to get the float value: float_value = (-1)^0 * mantissa_fractional * 2^exponent float_value = 1 * 1.002227783203125 * 2^108 Because the exponent is quite large, the resulting float value is a very large number.
Last updated: 2023-12-15

Post by paulpotat on Project size increasing continuously ^{CODESYS Forge talk (Post)}
I still have the same problem with Codesys 3.5 SP18. Initially, my project is ~5 Mo. I work on it for like 3-4 days and it goes up to ~10Mo. If I make an export of the project and import it in a new empty project, it goes back to approximately 5 Mo. Why is it doing this ?
Last updated: 2023-08-23

Post by bbm1995 on Security Screen - Custom Certificates for OPC UA Server? ^{CODESYS Forge talk (Post)}
Hi everyone, is it possible to use selfsigned/created certificates (eg. with X - Certificate and Key Management) as a OPC UA Server certificate in the Security Screen? As far as I know I can only upload client certificates to the PLC and move it to "Trusted", "Untrusted" and "Quarantined". Same question is on sps-forum.de
Last updated: 2023-08-23

Post by transmin01 on EL6751 Canopen_Manager issue ^{CODESYS Forge talk (Post)}
Hi, I have a Beckhoff EL6751 EtherCAT / CANopen gateway which fails on the Canbus when the CANopen_Manager is added. Currently no devices are connected to the EL6751. If I add a device, I get the same issue. If I add a device and connect the bus, I get the same issue. Is there something I am doing wrong? Regards Trevor
Last updated: 2023-09-12

Post by kdasystems on WebVisu on mobile devices ^{CODESYS Forge talk (Post)}
Hello I have a problem with web visu. When I open it to normal screen it is with good quality, but when I use it on mobile phone or tab then it is really bad quality, almost not possible to read the information. Can somebody help me what are the exact settings in the visu manager for this
Last updated: 2023-09-13

Post by dgrard on Camera RTSP Feed ^{CODESYS Forge talk (Post)}
Hello Is it possible to view a camera RTSP feed in a visualization? It seems as though the browser element doesn't support this and we are trying to replicate an example using the ActivX element with no luck. We are using the Windows Control Win x64 device with a camera connected via LAN. If it is possible, can you provide some instructions please. Thank you
Last updated: 2023-10-17

I don't know if this is where I should ask this, but I'm trying to get a Codesys OPC UA Client set up with a Kepware OPC UA Server ^{CODESYS Forge talk (Thread)}
I don't know if this is where I should ask this, but I'm trying to get a Codesys OPC UA Client set up with a Kepware OPC UA Server
Last updated: 2023-10-19

Post by romrot on I don't know if this is where I should ask this, but I'm trying to get a Codesys OPC UA Client set up with a Kepware OPC UA Server ^{CODESYS Forge talk (Post)}
Trying to create a Data Source under Data source manager, but I'm having issues with security. I get "BadUserAcessDenied" I don't know if there is something special I need to do on the Kepware server to make this work or what.
Last updated: 2023-10-19

Post by mawaloc on creationg on dynamic widgets ^{CODESYS Forge talk (Post)}
Hello, Is there is any way to create a different dynamic widget than what can be found on codesys. I would like to create similar with adding things like limits etcc. in codesys I just see 180 deg or 360 deg. and shape are differents Any tutorial on it. ThankYou
Last updated: 2023-10-20

Post by timvh on Send file from codesys to...... ftp, cloud, etc ^{CODESYS Forge talk (Post)}
You can use the (open source) FTP client in Forge. This works on 64 bit systems. See: https://forge.codesys.com/prj/ftp-client/code/HEAD/tree/ As this is open, the idea is that when you use it and make improvements to the source code, that you also commit this in a branch so others can also benefit from it.
Last updated: 2023-11-07

Post by ggis on Unable to connect to git remotes through Codesys. ^{CODESYS Forge talk (Post)}
When trying to connect to a Github repository in the Git remotes windows of Codesys, the user can be the account username or the account email, while the password is the Github token. (I know this is an old topic, but I lost some time figuring it out from the guides.)
Last updated: 2023-11-10

Post by ewi04 on Recipe Manager - RecipeManCommands, load & write wrong values, Bug? ^{CODESYS Forge talk (Post)}
It seems that there is a limitation with the STRUCTs. Does anybody know, what’s okay to save (add to the recipe) and what’s not okay? Or is there another problem with my project? If I have only an array in the recipe definition everything works perfectly (see project).
Last updated: 2023-11-15

Post by ivanmaltar on Update Raspberry Pi error ^{CODESYS Forge talk (Post)}
Hello, from today, I got an error when I try to open 'Tools/Update Raspberry Pi' and I got this error: There is no value with the specified name associated with this subkey. This feature worked before. I did not do any changes to Codesys installation. Codesys version is SP19.1, and CODESYS Control For Raspberry Pi 4.8.0.0
Last updated: 2023-11-30

Post by soped on How to generate EtherCat xml from command line ^{CODESYS Forge talk (Post)}
Hi Under tools->customize I have added the command "Generate ethercat xml" to my project so that I can export the configuration as an xml file. I can't find a way how to run that command from CLI, is that even possible and if a script is needed I would appreciate an example ?
Last updated: 2024-06-27

Sort by relevance or date