Post by ggaida on runtime dynamic modbus devices ^{CODESYS Forge talk (Post)}
Kurtk, I am working through a very similar scenario. I am curious if you have had any success since your post in implementing dynamic modbus configurations? Thx!
Last updated: 2025-11-20

Post by sb879 on Non-formal invocation of function blocks in CODESYS ^{CODESYS Forge talk (Post)}
Is it possible to do non-formal invocation of function blocks in CODESYS? I get an error when I try, see the attached pic. Also attached a pic from IEC 61131-3 describing non-formal invocations.
Last updated: 2025-12-04

Post by sb879 on Non-formal invocation of function blocks in CODESYS ^{CODESYS Forge talk (Post)}
Is it possible to do non-formal invocation of function blocks in CODESYS? I get an error when I try, see the attached pic. Also attached a pic from IEC 61131-3 describing non-formal invocations.
Last updated: 2025-12-04

Post by karsonsv on CODESYS HMI and 2 monitors ^{CODESYS Forge talk (Post)}
I need open visualization on two monitors (every monitor 19201080). In TargetVisu i configure Scaling Options as Fixed 38401080. But visualization open onli main monitor and onli half.
Last updated: 2026-01-02

Post by reinier-geers on Draw nails pattern ^{CODESYS Forge talk (Post)}
Hi I want to draw a nailpattern. But codesys Hasnt a draw command. And i dont want to draw 1000 nails and move them in position. Any one an idee ?
Last updated: 2026-04-20

Post by jeffyech on <Dereference of invalid pointer> ^{CODESYS Forge talk (Post)}
I have a program which calls a structure. while online with the PLC, I get: <dereference of="" invalid="" pointer=""> in the declaration values area. What are the causes of this? Can it be solved?</dereference> Version 3.5 of codesys.
Last updated: 2026-06-25

Post by alexschooneveld on OPC UA PubSub SL 1.3 — UADP WriterGroup with assigned PSS.SecurityGroup still publishes plaintext ^{CODESYS Forge talk (Post)}
Thank you for your answer. I did install certificates, especially for OPC UA Client/Server tests. This OPC UA PubSub test uses pre-shared keys, not certificates. By the way, I do you 3.5.22 patch 2.
Last updated: 2026-06-30

Post by arj3090 on Beckhoff CX9240 : Using Internal EtherCAT Bus ^{CODESYS Forge talk (Post)}
I installed Linux ARM SL and it recognizes the RJ45 ethernet ports, but I cannot get it to recognize the internal port for the IO cards.
Last updated: 2026-07-10

Post by mariussandu on OPC-UA ^{CODESYS Forge talk (Post)}
I updated the runtime to CODESYS Control for Raspberry Pi SL 4.22.0.0, SDK 3.5.22.30. Same outcome as before. Now I study if migrating to PFC100 is ok or to change to Siemens PLC because of this issue.
Last updated: 4 days ago

Post by mariussandu on OPC-UA ^{CODESYS Forge talk (Post)}
I updated the runtime to CODESYS Control for Raspberry Pi SL 4.22.0.0, SDK 3.5.22.30. Same outcome as before. Now I study if migrating to PFC100 is ok or to change to Siemens PLC because of this issue.
Last updated: 4 days ago

Post by dim54 on Disabling automatic logout from the owner user ^{CODESYS Forge talk (Post)}
Hello! Please tell me how I can disable the automatic logout as the Owner user (CODESYS 3.5 SP15 Path 2). I have to reconnect multiple times during the workday. Thanks!
Last updated: 2026-01-16

Post by ketanvaishnav on Redundancy Codesys Runtime, Synchronization ^{CODESYS Forge talk (Post)}
i am facing same data sync issue. i am use two 750-8212 (FW30) controllers. datas are sync from active to standby during changeover time, but datas are not sync from standby to active.
Last updated: 2026-01-30

Post by chaoschaos on Visualisation generates "Unresolved reference" ^{CODESYS Forge talk (Post)}
For the DynamicText error i have finally found a solution. You have to delete some libraries from your project. For me it was the WagoSysIcon library which wanted to reference dynamictexts even though i didn't have any in my project.
Last updated: 2026-02-02

Post by jslarbaletier on Unable to compare projects containing alarm manager 4.5.0.0 ^{CODESYS Forge talk (Post)}
Hi! I had the same issue and finally found a solution. Alarm Configuration was located in a “Visualisations” folder. I moved Alarm Configuration directly under “Application”, and the issue was resolved.
Last updated: 2026-02-05

Post by mohammedben on Fail communication between CODESYS and Fuxa SCADA via OPC UA ^{CODESYS Forge talk (Post)}
hi, When I try to establish communication between CODESYS and Fuxa SCADA via OPC UA, the connection fails, and I receive the following error: 2026-02-15T08:38:13.618Z [ERR] 'codesys' connect failure! Error: The connection may have been rejected by server, Err = (ClientTCP_transport6: socket has been disconnected by third party) 2026-02-15T08:38:13.619Z [ERR] 'codesys' try to connect error! Error: The connection may have been rejected by server, Err = (ClientTCP_transport6: socket has been disconnected by third party) 2026-02-15T08:38:13.622Z [ERR] 'codesys' connect error! undefined (1) Note that there are no problems when I establish communication with the UaExpert and OPC UA Client Simulator software. I also previously tried communicating with RapidSCADA and received the following error: Endpoint with the specified security options not found. And when I try to connect with "none" in the security policy, I get this error: BadSecureChannelClosed I have tried almost all the solutions available online and have not found a solution. I hope you can provide me with a solution that solves this problem. Thanks in advance
Last updated: 2026-02-16

Post by pernockham on Unable to deploy "Control for Linux SL 4.18.0.0" ^{CODESYS Forge talk (Post)}
Am I alone in this? Is this a known fault? Should I look for the reason of the lacking update option for "Control for linux SL" in my system or is it a potential fault in the codesys system?
Last updated: 2026-02-17

Post by thomasrek31 on Textfield display problem ^{CODESYS Forge talk (Post)}
Hello, have you found a solution? It seems I have the same problem as you. I can't remove the overlay, otherwise certain functions stop working.
Last updated: 2026-03-23

Post by thomasrek31 on Textfield display problem ^{CODESYS Forge talk (Post)}
Hello, have you found a solution? It seems I have the same problem as you. I can't remove the overlay, otherwise certain functions stop working
Last updated: 2026-03-23

Post by ulvis on CAA 3.5.16 TLS configuration - certificate ^{CODESYS Forge talk (Post)}
Hi, did yo have any luck with this? I am facing the same challenge. Using a WinCTRLx64 but I get AccessViolation error in my CmpTlsCreateContext() call.
Last updated: 2026-03-23

Post by husarz17 on How change Unity-ID in TCP Modbus Slave ^{CODESYS Forge talk (Post)}
I need the same issue. In my application TCP server on raspberry (codesys) should have UnitID 1. But it only works when I am requesting with UnitID 255. And my application can't work with this parameters...
Last updated: 2026-03-31

Post by husarz17 on How change Unity-ID in TCP Modbus Slave ^{CODESYS Forge talk (Post)}
Good to know there's a solution to this problem. I hope you'll be able to share it with me. I can't wait to hear about it.
Last updated: 2026-04-20

Post by reinier-geers on Network variable stops sending ^{CODESYS Forge talk (Post)}
What version. 20.5 ? ive got also problems wiyth that version. Online change, it hangs itself after one hour. Then one project can problems. Ive change display with 21.0 . At home i turned on the 20.5 display. After 1 hour i goes to stop.
Last updated: 2026-05-06

Post by julianramirez on Codesys Trend - setting Y axis minimum and maximum as variables - error ^{CODESYS Forge talk (Post)}
Hello Hannibal, I am using real vars and it works, however, if I update those vars in real time it doesnt quite change it on y axis, do you think it is because it is not an integer?
Last updated: 2026-05-21

Post by tvm on Generic Variables and FDB ^{CODESYS Forge talk (Post)}
I also ran into this, try using Coil<1> as the type in the FBD box. From what I understand, with VAR_GENERIC CONSTANT, the compiler creates separate data types for each different function block declaration.
Last updated: 2026-07-22

Post by alex-at-xana on EThercat Dynamic configuration ^{CODESYS Forge talk (Post)}
Hi Everyone, For a fast monitoring system I am using Ethercat oversampling and timestamping inputs. As the customers has a lot of different configurations out in the field, we went for a dynamic Ethercat configuration. Already got the whole detection chain working but now I am stuck since two days in debugging the configuration. Here are my quesitons: I extended the dynamic config example for the EL3632 16#0E303052: //EL3632 pSlave^.SetDCSettings(TRUE,TRUE,80,80,TRUE,4000,0,0); pSlave^.AddSyncManager(16#1000,128,16#26,TRUE,3); pSlave^.AddSyncManager(16#1080,128,16#22,TRUE,2); pSlave^.AddSyncManager(16#1100,0,16#4,TRUE,1); pSlave^.AddSyncManager(16#1110,214,16#20,TRUE,0); pSlave^.AddFMMU(0,214,0,7,16#1110,0,1,1); pSlave^.AddFMMU(0,1,0,0,16#80D,0,1,1); xKnown := TRUE; This leads to a PLL Error for these devices. I double and triple checked the configuraton, but cannot find the issue. There seems to be one difference: the config dialog creates a startup parameter: 16#10F3:16#05, Name: Command_0, Value:0. Bitlen: 16, Stop on fault: false, jumpt at fault: false: next line: 0 a) I do not find information on how to set this in my code. Can you help me there? b) Without trying to set the value, I get a PLL error for these devices in the master log. Is the config wrong? c) Do I need to set the Master to Autoconfigure or Manual? I used autoconfigure for my tests. The stack creates input data addresses for the slaves input data range (pSlaves[i].InputData) which are different from those created when I use the Engineering tools dialogs to configure Ethercat. Specifically, the addresses seem to be aligned at 16 byte boundaries when they are created using the engineering tool, but may appear at uneven addresses when I use the script in dynamic config. I did not try to access ULINT at uneven addresses yet, but I am suspecting this may be a problem. Do I need to manually align the addresses ? Any help is appreciated...
Last updated: 2024-09-10

Sort by relevance or date