Post by micik on Reverse bytes in an array ^{CODESYS Forge talk (Post)}
Hello, I'm getting the data in Codesys that is an array of 8 bytes. From this array, I need to foram LREAL number, however, because of different endiannes I need to reverse bytes in this array and then copy to a LREAL variable. For this I'm using a loop and it works OK. I wonder if there is a built in function to do this. I have found CAA Memory library but it has functions like reverse bytes in DWORD. But it seems it doesn't have what I need. https://content.helpme-codesys.com/en/libs/CAA%20Memory/Current/CAA_Memory/Reverse-Bit-Swap-ByteWord-order/ReverseBYTEsInDWORD.html What I need is a function to reverse bytes in an 8 byte array, or something similar.
Last updated: 2024-08-22

Post by micik on False Notification Application Error with raspberry pi 4 ^{CODESYS Forge talk (Post)}
Hello, I have just went through all steps shown on Codesys YT channel https://www.youtube.com/watch?v=RPoPscbo3Kc And it works, I have installed PI OS 32 bit and choose Single Core. However, immediattely when I create standard project with Raspberrz pi device, "Application" is underlined, like there is an error, but in reality there are no errors, and I cannot see what are these 3 messages like shown in attachment. Aside for this red underline, everything seems to work fine. How to correct this? Thank you! Update: I have found what errors are, but not sure how to correct them: Identifier 'IoDrvGPIO' not defined Function block 'IoDrvGPIO' must be instantiated to be accessed 'IoDrvGPIO' is no component of 'IoDrvGPIO'
Last updated: 2024-09-03

Post by damian177 on Problem with downloading OPC UA tags by Data Source Manager ^{CODESYS Forge talk (Post)}
Hi, In Codesys V3.5 SP20, using Data Source Manager I am trying to connect to the OPC UA server and receive tags from it. The connection is ok, but the Codesys have a problem with downloading Tags group. The window (downloadingTags.jpg in attachement) never stop. After waiting for a while, I disconnect the connection and only the Server group remains downloaded, with OPC UA server diagnostic data (and this is read in Codesys). Of course, I tried connected via another OPC UA client : UaExpert , and everything works as it should, all tags are downloaded (Uaexpert.jpg screen). Has anyone on the forum encountered the OPC UA client configuration in Codesys? Is it possible to manually request the appropriate tags from the OPC server for reading in Codesys?
Last updated: 2024-09-03

Post by yannickasselin on codesys VLAN tagging ^{CODESYS Forge talk (Post)}
Hi, I am looking for exactly the same thing. I would think that using a layer 2/3 managed switch should work but I am not convinced. I would like to test it in order to see if it would be possible to run many Codesys Docker instances on a server and run only 1 ethernet cable from the server to a managed switch closer to the machines beeing controlled instead of having to run multiple long ethernet cables. I was going to buy a managed switch in order to test it but I want to first make sure it is possible and I want to figure out exactly what kind of switch I would need. Is this even possible? I think this is a feature that would be very useful paired with "Codesys Virtual Control SL". Thank you
Last updated: 2024-09-07

Post by davidbo on RPI can system operation like rm in a shell have an impact on a Task cycle time ^{CODESYS Forge talk (Post)}
I have noticed that a rm file1.txt command on a shell has an impact on the cycle time for a TASK writing to file2.txt. Seen in the Monitor fane of the Task configuration Furthermore if a TASK makes a system call like rm, its cycle time increases of course but it seems to have an invisible impact on other TASKs too. I have a TASK for handling communication over the CANbus (SPI) where it stops sending "Heartbeats" for many seconds when another TASK does a system rm. Why is that not seen on the Monitor fane? Is even codesyscontrol paused when system calls are made? The CPU load is about 30-40%
Last updated: 2024-09-23

Post by timvh on Clarifications regarding the appropriate runtime system to use ^{CODESYS Forge talk (Post)}
If you are not using any specific Raspberry Pi functionality, then probably the "universal" Control Linux ARM SL is the approriate runtime to run on the Pi. For the license it doesn't matter which runtime version you choose, because this is not hardware based anymore, but application based. Best is to use the latest version of CODESYS. To determine which license you need, double click on your device, go to the tab License metrics.... Generate the code for your application and see which license you need based on the metrics of your application.
Last updated: 2024-09-24

Post by rmaas on TargetVisu for Linux SL not starting ^{CODESYS Forge talk (Post)}
Hello, I am trying to get TargetVisu for Linux working but i am having some troubles. The problem is that after installation it is not starting automatically on boot and i cannot start it from the update Targetvisu tool. When i try i get the following error (see attached screenshot) The file /opt/codesysvisualization/scripts/codesysvisualization_start.sh is missing... Steps performed: - installed fresh Debian 12.7 on virtual machine - installed all required libraries as described here: https://content.helpme-codesys.com/en/CODESYS%20Control/_rtsl_target_visu_for_linux.html - then installed the TargetVisu for Linux SL 4.13.0.0 using the Codesys IDE Does someone know how i can fix this? Best Regards, Rinie
Last updated: 2024-10-02

Post by bjarne-pagaard on OPC UA Server Status on Win RTE ^{CODESYS Forge talk (Post)}
Hi there, An "OPC Expert" client software is connecting to a Codesys Control RTE (x64) OPC UA Server. It reads only about 25 variables every 5 minutes. The OPC UA Server seems to shut down on the Codesys runtime. Is there any way to get information about the Codesys OPC UA Server status? Restart it? There is nothing in the PLC Logs after the OPC UA Server has started. It works for a while, then it doesn't. Any ideas? Any way of getting more info out of the Codesys OPC UA Server? -Bjarne
Last updated: 2024-10-21

Post by niallel on CamBuilder and first boundary position not zero ^{CODESYS Forge talk (Post)}
Hi, I've read the CamBuilder documentation and it shows to use the left boundary of the first segment as SMCB.BoundImplicit(), so that the transition is as smooth as possible. With this it sets X and Y to 0. My first slave position is not 0 (say for example it's 100), so I would set it with SMCB.Bound(0,100). My question is that when the cam goes back to the start (Periodic := TRUE) , will it blend with the last position (360, 100) if I do this? I imagine it will, but the documentation isn't clear as the information in the Periodic Cams only says to set Smooth Transition in the cam properties - but when I'm defining it with code there isn't an option for Smooth Transition to be set. Hope this makes sense? Many thanks,
Last updated: 2024-10-23

Post by jeroenaero on CodeSys Raspberry pi I2C driver not found ^{CODESYS Forge talk (Post)}
Hello, We have a problem with CodeSys on a raspbery pi with an ADS1015 analog to I2C module. It can't find the I2C device on the i2c bus, it says No I2C Driver Found. When we use the RPI terminal we can find the I2C device and read it out. The i2c-1 bus is also accessible from codesys. The device address of the Analog to I2C module is 0x48. Can someone have a look what the problem is? i submitted the screenshots in the attachments. i also include the device description and library.
Last updated: 2024-11-07

Post by ofey on OPC server crash ^{CODESYS Forge talk (Post)}
Hi! I repeatly encounter a crash of the OPC server, which forces a reboot of the controller with frequent connect/disconnect to the server. Have any of you encountered this before? And is it a workaround? ie. deny that particular client connection by timeout or similar instead of crashing the PLC? This is during a development phase of the user interface. Up to 3 others connect/disconnect frequently to test their code. It is a bit troublesome of the PLC crashes several times a day because of this :( I greatly appreciate all comments. I hope it exists a fix for this, or something that hinders the crash. I attached the logfile for the crash
Last updated: 2024-11-26

Post by pernockham on Inheritence of struct, ^{CODESYS Forge talk (Post)}
Apparently my construction will not work as any of the sub-types are not be able to accept any (further) value-initiation. Ie: string_item : log_data_base := (string_value := 'test', val_type := STRING_); is not eq to (the string_value will not be assigned): string_item_2 : log_data_string := (string_value := 'test'); Because effectively for the compiler this is eq. to a "double" assignment where the compiler sees only the first assignment (my guess). string_item_2 : log_data_base := (val_type := STRING_) := (string_value := 'test'); Im not sure this should be treated as a bug, but it would surely be nice to be able to use this construction (compiler is 3.5.20.40). Anyone see any other alternative for solution (other than 4 complete STRUCTS with all fields individually defined)?
Last updated: 2025-03-07

Post by struccc on Problem Reading Registers via Modbus from non Codesys device ^{CODESYS Forge talk (Post)}
Hi, Might be a good idea first to try out the connection and the device with some handy software, like Modbus Poll. There you can see better, what's really going on... - Is it really connected? - What error code does it return? - Can it read from the register address? - Maybe try Input registers and Holding Registers - can make a difference - Sometimes register addresses are messed up: shifted +-1 (mixing of 2 standards) - Sometimes register addresses start with offset 30000, 40000 ... - Are you using the right protocol? - Is it RTU or TCP? Maybe ASCII? - Can even have a look at the data packets, etc... All this is easier to figure out first with some modbus utility... and then to set it up in CODESYS should not be an issue. P.
Last updated: 2025-03-09

Post by r-c-r on SM3RaspiStepper 0.0.0.6 issue ^{CODESYS Forge talk (Post)}
Hello, I noticed that version 0.0.0.6 is now available, so I tested it using CODESYS V3.5 SP19 Patch 7 and SoftMotion 4.17.0.0. While the project compiles and downloads without issues, I encountered a problem with the 'Enable: GPIO pin number that is set when the axis is enabled (with MC_Power) (0: not used)' functionality — it no longer works (HIGH level not present at the output pin). I observed the same behavior with version 0.0.0.5, whereas version 0.0.0.4 functions correctly. Could you help me identify what might be causing this issue or suggest how to resolve it? Thanks.
Last updated: 2025-03-19

Post by rossanoparis on Internal Error (ARM): Unsupported conversion! With new version v3.5 SP21 ^{CODESYS Forge talk (Post)}
I have updated CODESYS development tool to the version v3.5 SP21 (64bit) The previous version was v3.5.20.40 Compiling an existing application with the new evelopment tool I get the following error. kunbusiodrvrevpibridge, 1.4.1.0 (kunbus gmbh): IoDrvScanModules [IoDrvRevPiBridge](Line 51, Column 1 (Impl)): Internal Error (ARM): Unsupported conversion! This error was not reported in the previous compiler version and is now highlighted in a third-party library, which I cannot change or modify. The error is due to the following conversion: m_udiError := TO_UDINT(excCode); . The excCode variable is a system type, declared as shown below, and should be converted to a UDINT excCode : __SYSTEM.ExceptionCode; m_udiError: UDINT; . I would appreciate it if someone could provide feedback on this issue.
Last updated: 2025-04-15

Post by kut69 on Retain / Persistent Variables in Codesys for Raspberry Pi ^{CODESYS Forge talk (Post)}
Hi, I am interested in details about the .ret file in the filesystem. I have already a project where the file is used (write on demand, read by start) and I want to share it as 'default input' for test devices using the identical application. Opening the .ret file content in a hex editor (I only use a single string retain var) I asked myself what the meaning of the first 24 bytes is. It neither contains a handle to the application nor a reference to the variable. Is this maybe a timestamp? Or a CRC/checksum? Regards, Thomas
Last updated: 2025-05-19

Post by abuckie on Getting raw value as full resolution for ADS1115 ^{CODESYS Forge talk (Post)}
I just found this and I am getting a value larger than 16 bit, around 81000 something. I am reading a 5 volt value and I am using level shifters for the i2c bus. This is how I have the channel configured: ADS1115.usiAddress := 16#48; ADS1115.ChannelConfigs[0].Active := TRUE; ADS1115.ChannelConfigs[0].PGA := FSR_6144mV; ADS1115.ChannelConfigs[0].InputMux := Single_0; RawAnalogValue := ADS1115.Channels[0].Value; It looks like every value is a multiple of 3. Any idea where to look to fix this? I think i found what I want to change in UpdateChannels Channels[FChannelNo].Value := INT_TO_REAL(WORD_TO_INT(LValue) * GetFullScaleRange(ChannelConfigs[FChannelNo].PGA)) / 2048.0; I try to edit it but I can't, sorry if this is a basic question, I am new to CODESYS.
Last updated: 2025-05-22

Post by kareem-pt on Velocity is too low even though correct value is reported ^{CODESYS Forge talk (Post)}
Hello, I'm playing around with a single axis. I've setup scaling and set the drive to move 360 degrees in the commissioning tab. The axis does move 360 degrees, but it moves much slower than the 360 degrees per second that I set for the velocity. It seems to be about 3 times slower (taking about 3 seconds instead of 1). This is despite the set and actual velocity both being displayed as 360. The acceleration, deceleration and jerk are all set to very high values. I'm just running this on my PC, using demo mode (no license purchased yet). I've attached a video showing the problem. Does anyone know what the problem could be? Thanks
Last updated: 2025-06-06

Post by viksym on How to get the motor scaling value from code ^{CODESYS Forge talk (Post)}
Is there a way to see what value is set as the "Work travel distance per motor rotation" that is set in the Scaling menu of the axis ? I am working on my own homing function block for sensorless (hardstop) homing and I want to make it be universal between different axes with different motor's scaling for distance per rev so I need to know this value from the axis itself. I know I could do it by just creating an input variable for the function block but I'm leaving that option as a last resort.
Last updated: 2025-06-12

Post by andrej on Signing of Boot Application for Raspberry Pi ^{CODESYS Forge talk (Post)}
Hello all, I would like to sign my boot application for my Raspberry PI. I generated the X509 Certificate and loaded it to the raspberry. It is successfully displayed as trusted certificate. However, I cannot download and start the Application to the Rasperry, due to a signature mismatch.The error message is rather clear, but I still don’t see how I can fix the issue, since the certificates on the Controller seem to mach the certificate in the user profile. Could you tell me where the error is or which step I am missing. Many thanks and kind regards Andreas
Last updated: 2025-07-17

Post by andrej on Signing of Boot Application for Raspberry Pi ^{CODESYS Forge talk (Post)}
Hello all, I would like to sign my boot application for my Raspberry PI. I generated the X509 Certificate and loaded it to the raspberry. It is successfully displayed as trusted certificate. However, I cannot download and start the Application to the Rasperry, due to a signature mismatch.The error message is rather clear, but I still don’t see how I can fix the issue, since the certificates on the Controller seem to mach the certificate in the user profile. Could you tell me where the error is or which step I am missing. Many thanks and kind regards Andreas
Last updated: 2025-07-17

Post by andrej on Signing of Boot Application for Raspberry Pi ^{CODESYS Forge talk (Post)}
Hello all, I would like to sign my boot application for my Raspberry PI. I generated the X509 Certificate and loaded it to the raspberry. It is successfully displayed as trusted certificate. However, I cannot download and start the Application to the Rasperry, due to a signature mismatch.The error message is rather clear, but I still don’t see how I can fix the issue, since the certificates on the Controller seem to mach the certificate in the user profile. Could you tell me where the error is or which step I am missing. Many thanks and kind regards Andreas
Last updated: 2025-07-17

Post by dkugler on Project loses 'Download time' information ^{CODESYS Forge talk (Post)}
and if you copy or transfer a project to another place, copy not only the .project, copy .compileinfo .bootinfo and .bootinfo_guids then we figured out it is more often possible to go online without full download. If you build an archiv and extract it, some of this files are missing and login isn't possible without download. I work with V3.5 SP16 Patch 4. I don't know if this problem of the archiv is solved in newer Versions/SP's and I don't know what the problem of Codesys is to help out a lot of programers of this very annoying problem or at least help with a workaround
Last updated: 2025-09-18

Post by durallymax on Persistent Vars ^{CODESYS Forge talk (Post)}
Looking for a better way to manage Persistent Variables. We tend to have local vars in our FBs that need persistence through downloads as the systems are updated/altered on a regular basis. Retain would suffice if we had an easy mechanism to backup and restore like we can with Persistent variables and recipes. Although not having to remember that step with Persistent variables is preferred. We're running into issues with persistent storage capacity (WAGO PFC200) using the Persistent variable list (and adding all instances). It appears there are many ways to handle this, some with recipes, some with files, others with application manager. Is there a solution that exists that is as simple as declaring as Persistent and managing elsewhere? Or do we need to move onto periodically writing CSVs?
Last updated: 2025-09-22

Post by pernockham on *Exception* Async service: ServiceGroup=17, IP=0x5fa45617, Component=CmpSrv ^{CODESYS Forge talk (Post)}
*** The system may be in an inconsistent state, please reboot *** *Exception* Async service: ServiceGroup=17, IP=0x5fa45617, Component=CmpSrv Every time at the instant that I Login to the system a message that the "system may be in an inconsistent state, please reboot" is written in the log. If I logout and repeat login a new entry is set. My system is a "Control for linux SL" running on a debian linux host. Im running it on my desk without any IO attached so message might be caused from that, but I doubt i have seen it before. Rebooting makes no difference. Anyone that have a clue of how I should interpret this error message?
Last updated: 2025-09-26

Sort by relevance or date