Post by gilbertamine on Comparing Arrays of structure ^{CODESYS Forge talk (Post)}
Hi Everybody, I'm looking for a simple way of comparing two array of a structure. My structure is define like this : TYPE Positions_T : STRUCT PosX: DINT; PosY: DINT; PosZ: DINT; END_STRUCT END_TYPE I have multiples Var : ARRAY [0..220] OF Positions_T, that I need to compare quickly. I don't really want to do a Loop that goes by every 220 points and compare each one of them so I was wondering if there is another way. I came accross the MEM.Compare function, but it require to know the size in Bytes of the memory, and I don't know how to do that... Has anybody an idea on how to do the comparing easily ? Thanks in advance
Last updated: 2024-08-22

Post by m83coding on Raspberry Pi Codesys SPI Master ^{CODESYS Forge talk (Post)}
Hello, I am trying to control shift registers 74HC596 and 74HC165 via Raspberry PI with SPI interface. So far I did it with a Microcontroller and now I wanna upgrade my Projekt with Raspberry Pi and Codesys Software to be more flexible. I tried to adapt PiFace Function Block to just send or recive a 8 bit via SPI interface of the my Raspberry Pi. With following code (see attached screenshots) * PLC_PRG * PiFaceDigital * PiFaceDigital.write8 * PiFaceDigital.read8 I have a signal at SCK and MOSI pin of the PI, so far so good. But I really struggle with the unterstanding of the code. Is there some detailed description of each line of code? Or is there somebody in the community who can explain each line of code? Or is there a more simple way to send / recive 8 bit via SPI? Manuel
Last updated: 2024-04-23

Post by timvh on Configuring a 2's compliment ^{CODESYS Forge talk (Post)}
You could create a DUT of the Type Union and add an array of 2 bytes + an Int. Then write the byte values in the array of the Union and read the Int. Or VAR iInt : INT; byHigh : BYTE := 2#1111_1111; byLow : BYTE := 2#1111_1111; END_VAR iInt := TO_INT(byHigh*16#100 + byLow);
Last updated: 2024-09-28

Post by janber on REFERENCE TO in an array ^{CODESYS Forge talk (Post)}
Hi all, in the online help it written, that array of reference to data type is not possible. Ok... but if I create array of struct of reference to - everything works fine - please see the screenshots: and it works this way OK. Is it intention or error in compiler 3.5.18.20 and we should avoid it? Thanks a lot, Jan.
Last updated: 2024-10-14

Post by jarnok on How to know if output if function block is used ^{CODESYS Forge talk (Post)}
Hi, Is it possible to know of an output of a function block is used? I've found there is a way to find unused inputs of a fb, through the attribute: is_connected. But I'm wondering if the same can be done for an output. Thanks in advance!
Last updated: 2024-10-15

Post by tyronnosaurus on SysLibMem.lib Where To Download? ^{CODESYS Forge talk (Post)}
It should come by default on a normal install of Codesys 2.3, but it's a bit hidden: Like for any other library, go to Resources > library Manager > Right click on list of libraries > Additional library. On the browser that opens, instead of looking in the default folder, use the dropdown menu at the bottom to change the folder (SysLibMem should be on the 3rd folder).
Last updated: 2024-11-11

Post by aufwindsh on Visualization Scaling the Keypad ^{CODESYS Forge talk (Post)}
Hello everyone, is there an option to change the Scaling of the Keypad? I have an 15inch HMI with a resolution of 1920x1080p and the Keypad for the Login of the usermanagement is still to smals to have a great user Experiance. I really appriciate any feedback. Thanks.
Last updated: 2025-08-02

Post by beavel on Opening and saving files with fileOpenSave dialog ^{CODESYS Forge talk (Post)}
1 + Replying in hopes of getting an answer here. I would also like to modify the look of the FileOpenSave Dialog. I have successfully adjusted the looks of the User management Dialogs but can not find a library file to adjust this particular one. Any help would be helpful. @thk @eschwellinger @sheberle .
Last updated: 2025-09-08

Post by snhatton on Testing of Codesys program ^{CODESYS Forge talk (Post)}
There is a tool called test manager that is part of the Professional Developer's Edition of CODESYS. I would take a look at this tool for your testing purposes. There is a free 30-day trial so you can evaluate if the tool will meet your needs before investing in the license.
Last updated: 2023-12-08

Post by kirsipr on Color of empty table and table header ^{CODESYS Forge talk (Post)}
I have managed to change my dynamic visu table colors with the template for each column to dark like my rest of the webvisu background is. How ever the empty table (when not populated) and the table header stays white / gray. Is there same way to modify the colors of header and empty table?
Last updated: 2024-03-13

Post by nano on Map in Codesys ^{CODESYS Forge talk (Post)}
There are several versions, u can use an recipt, shm, perstance variables, persistsnce manager. all these ways has some pro's and con's and some of them depending on preparation of the controller byself. others depending on your functionalies and dependencies on project. for all of these ways, you can find the informations on the onlinehelp or from controller-oem
Last updated: 2024-04-04

Post by vincentd on Datasource OPC UA Client error ID:7012 ^{CODESYS Forge talk (Post)}
I have not used this client / server OPC UA combination since. We were only making some kind of proof of concept. I did understand that there could be some kind of bug. I do not know if the supposed bug has been resoved since. Perhaps you could try what piautomation is suggesting
Last updated: 2024-04-05

Post by thieulam on Codesys access to DICTIONARY OBJECTS of ethercat (CoE ) Servo Drive ^{CODESYS Forge talk (Post)}
Hello to all! How can I read or write, via my main code (ST), to the registers present in the DO of my ethercat CoE servo drive? These objects appear in the list of the INITIALIZATION page, and from here I can only access them at startup. How do I access it in run time from my main PLC_PROGRAM?
Last updated: 2024-06-19

Post by sturmghost on Mimic behavior of the visualization button element with a custom button ^{CODESYS Forge talk (Post)}
Im wondering how Codesys is doing the mouse event capturing with their visualization button element? If you add such a button without configuring any input configuration event (like OnMouseDown) or button state variable and then click on the button, the button changes to the visual pressed state and back if you release the button (so they must react to an OnMouseDown event). But how? If I try to mimic this behavior with my custom button visualization element (like a basic rectangle) I need to use an input configuration event to change the color of the button (to make it look like the button was pressed on OnMouseDown event). When I try to add this button via a Frame-Element to my main visualization page I'm unable to use an input configuration event on the Frame-Element because the input configuration event on the button element won't be evaluated anymore (it seems like you can't stack input fields, e.g. invisible input elements, onto each other). Hence the button is not shown pressed anymore. How they do it?
Last updated: 2024-08-04

Post by paulorb on STRUCT AT %MW1000 ^{CODESYS Forge talk (Post)}
Hi I am trying to use STRUCT to parse commands from Modbus/TCP, Modbus client will fill the bytes related to a specific command (type, parameters), then PLC (Codesys) will access the command parameters. A STRUCT will simplify a lot the process of parsing the data, so I don't need to parse byte per byte, address will be mapped to a struct and I can use it for parsing the data. From what I understood, the compiler does not allow me to specify the location of the struct for a %MW register. VAR_COMMAND AT %MW1002: structGenericModbusCommand; This will throw: Bad declaration, use '%ML' for 'structGenericModbusCommand' variable But If I change it to %ML, when you go online you see that it is actually allocating the struct in another memory address. When we go online, on GVL we can see: VAR_COMMAND. structGenericModbusCommand %ML1002 commandType COMMANDTYPE %MB8016 ... %MB8020 I am not specifying a pointer or a reference it is a struct type, why is it mapping to a %MW location (random one). How can I control where it is mapping to? I need a consistent way to map STRUCT to specific modbus address. Is it possible? Thanks, Paulo Note I am using a Codesys OEM: Schneider Machine Expert Logic Builder (M241)
Last updated: 2024-08-13

Post by egau on Enable and Disable Project IO programmatically ^{CODESYS Forge talk (Post)}
Hi @eschwellinger, I tried this with Modbus COM slaves. I was able to disable them (slave becomes greyed out in the device tree), but the DED.Reconfigure "eError" output shows "NOT_SUPPORTED". After this, when I tried to re-enable the slave, it did not work (device stayed greyed out in the device tree), and the DED.Reconfigure "eError" output also showed "NOT_SUPPORTED". Is there something to do about this, or the device just doesn't support reconfiguration? P.S: I tried this running locally on my computer (not in simulation mode). So of course I was not physically connected to the devices. I have two similar projects, but one of them doesn't have the Modbus_COM devices. I know I can "Exclude from build" the devices for that project, but I would really prefer not to do this if possible. I would prefer to dynamically toggle a configuration variable that would enable or disable the slaves.
Last updated: 2025-03-14

Post by toby on Ethernet/IP communication with Omron NX1P2 ^{CODESYS Forge talk (Post)}
Hey guys, I'm very much a noob with networking, it's my achillies heel, and this is my first networking project using Ethernet/IP. Any help offered is GREATLY appreciated. I'm trying to network a Codesys Project with an Omron NX1P2 PLC. I'm using EIP due to hardware restrains. I've added the fieldbus, EIP scanner (as the master), and made a Network Variable List. On the Sysmac Studio end, I've made the variables and set them to network inputs/outputs, registered them in EIP settings, but when I try to set the target device (the Codesys project), I suspect I need to import an EDS file for the EIP mapping. Back in the Codesys project, I'm not sure how to: - Make an EDS file to share with Sysmac Studio - How to link the target device (Omron PLC) to the EIP fieldbus - How to map the inputs from the Omron PLC. Im sorry for my very open request for help, i'm kind of lost looking through the various forums/video/tutorials as many of them dont match what im trying to do. Any help, or sample programs would be so so greatly appreciated. If you need any further clarifications, please feel free to ask. Thanks in advance, Toby
Last updated: 2024-01-24

Post by nixola on CmpCharDevice blocks gpiochip access on Raspberry Pi 5 since update from SP18 to SP21 ^{CODESYS Forge talk (Post)}
Hi, I added the following lines to /etc/codesyscontrol/CODESYSControl_User.cfg: [CmpCharDevice] PermittedPath.0=/dev/i2c* PermittedPath.1=/dev/spidev* PermittedPath.2=/sys/class/gpio/* PermittedPath.3=/dev/gpiochip* However, I'm still unable to read or control GPIO pins from any CODESYS application. Specifically, setting the pin direction (and, thus, the IoDrvGpioSysfs driver configuration) fails, with a rather non-descript error in the logs: Description Component Setting direction failed for GPIO pin 586 IEC Update configuration failed from driver IoDrvGPIOSysfs CmpIoMgr I'm running CODESYS Control for Linux ARM64 SL version 4.21.0.0; it's running in rootless mode, as the codesyscontrol user, but said user is in the gpio group and can otherwise normally interact with GPIO, both via gpioset/gpioget and via the sysfs driver in /sys/class/gpio/. The system is a custom 64-bit Raspberry OS based distro, running on a Raspberry Pi CM5 on kernel 6.18.34 with PREEMPT_RT scheduling.
Last updated: 4 days ago

Post by brouwyka on JSONByteArrayWriter string result incorrect order ^{CODESYS Forge talk (Post)}
Hi @TimvH, As discussed in our email contact, your example does not actually test/reproduce the bug I am describing: Adding to the JSON builder on later cycles works fine. Your example works because you do the following: 1. You finish the first cycle (xFirst) with adding an object to the array with 2 fields; 2. When the next cycle is triggered (xAdd), you immediately start with adding another object to that array. This works fine as the last thing you did before #2 was the addition of the array and an object to it. To reproduce the bug you should be doing the following instead, as I showed with the code I shared with my first post: 1. Create the array - save the index that is returned; 2. Add an item, either a primitive or an object, to the array; 3. Add an item outside the array (anything: a primitive, a new array, a nested object, etc); 4. Add another item to the array using the index you saved at #1. You will now see, as I shared in my initial post, that the second item is placed completely outside the root JSON object. This also happens to anything else you try to add after step #4: everything after this point will be added outside the root JSON object: the JSON is completely broken. Important to note is that this not only happens with arrays, but also with nested JSON objects. Once you add something outside of a nested JSON object, you can no longer add anything to that nested JSON object, as that causes the exact same bug. This also applies to arrays of objects, so if in your test you had tried adding a new key-value pair to the first nested object in your array after you created the second nested object, you would also run into this bug. It seems that the JSONByteArrayWriter (I haven't tested the other writers in the JSON Utilities SL library, so I don't know if they suffer from the same problem) simply does not handle any JSON fields that add brackets (so arrays with "[" & "]" and nested objects with "{" & "}") well, and closes them prematurely instead of checking if any later JSONElements in the JSONData's array belong to any of these bracketed fields. After reviewing the objects & functions of the JSON Utilities SL library, my guess is that either the JSONByteArrayWriter linearly goes through the array of JSONElements in the JSONData and only checks the diParentIndex of each JSONElement in direct ascending order, OR if it does use the JSONElement.GetChildren(); method, that this method is either broken and doesn't give all children correctly to the writer. Neither explains why everything completely breaks, and you cannot even add to the root JSON object anymore, however, so there is probably more than just that going wrong in the writer. To me, after a full week of testing and attempting workarounds, this seems like a bug in the library that needs to be fixed by Codesys, as I cannot see anything wrong in the JSONData constructed by the JSONBuilder - this seems purely a problem in the writer.
Last updated: 2026-06-15

Post by ihatemaryfisher on Sorting array of any-sized structure ^{CODESYS Forge talk (Post)}
With that I could make an array of varying size, but would still have to define the array type in the function's declaration VAR_IN_OUT stArray: array [*..*] of <pre-defined data type> END_VAR I wanted a function that could take an array of any type (e.g., a structured VAR) as an input. That way I could call it in multiple POUs to handle different arrays structures.
Last updated: 2023-08-18

Post by timvh on gateway problem ^{CODESYS Forge talk (Post)}
Maybe select the local gateway instead of the gateway on the remote device?
Last updated: 2023-08-31

Post by helcioburd on Async Manager ^{CODESYS Forge talk (Post)}
Do you have an example of that uses Async Manager?
Last updated: 2023-09-06

Post by eschwellinger on Official MQTT-Client: MAX_RECEIVE_BUFFER_SIZE_EXCEEDED ^{CODESYS Forge talk (Post)}
...and reduce the load of the plc
Last updated: 2023-09-26

Post by martinlithlith on Raspberry Pi: List of available drivers / libraries ^{CODESYS Forge talk (Post)}
As most of the posts are moved here around 2015, what would be the right version of codesys to run? Would it be better to install a older version of codesys or should i keep on downgrading libraries? Is there any work done to update theses libraries? It´s been a few years since the last update in this post, are there new libraries/devices for raspberry being added/posted somewhere else? Thanks, Martin
Last updated: 2023-10-17

Post by simotion on Axis_Ref_SM3.perfTimers ^{CODESYS Forge talk (Post)}
Yes but what exactly does each of them stand for?
Last updated: 2023-11-24

Sort by relevance or date