Post by baott569 on CODESYS OPC UA Security: HMI Client Not Receiving Server Certificate ^{CODESYS Forge talk (Post)}
Hello everyone, I am currently using OPC UA in CODESYS with the security mode BASIC256SHA256 – Signed and Encrypted. The OPC UA Server is running on an RTE CX device, and the HMI is running on another computer. I have reviewed many CODESYS documents and successfully established communication when the security mode is set to None with Anonymous login. However, when security is enabled, the server does not provide its certificate for the CODESYS HMI client to trust. Interestingly, the client can send its certificate to the server, and UAExpert works normally, but the CODESYS HMI client does not receive the server certificate. Can anyone help clarify what I might be missing? I have been stuck on this issue for three days. If I missed or misconfigured any step, please let me know. I believe I am stuck at step 15 in the following CODESYS guide: Encrypting the Communication of a Data Source OPC UA Client https://content.helpme-codesys.com/en/CODESYS%20Communication/_cds_encrypt_communication_data_sources_opc_ua_client.html Thank you very much.
Last updated: 2026-01-06

Post by mtorell on Safe Editor in codesys v3.5sp21p30 ^{CODESYS Forge talk (Post)}
How do I negate an output signal from an OR gate. I have tried right click to no avail and I cannot find an propriate NEGATE box? I want to save the output from the block to an inverted variable.
Last updated: 2026-03-12

Post by mjam04 on AM243 LaunchPad as PROFINET Device with CODESYS – RPC Aborted error when scanning devices ^{CODESYS Forge talk (Post)}
Hello, I am currently trying to use the AM243 LaunchPad as a PROFINET device and connect to it using CODESYS. In my setup I am also using a Raspberry Pi running the CODESYS PROFINET Runtime, which acts as the PROFINET controller. The setup of the Profinet controller is correct, so all devices are in the same subnet. However, I encounter an issue when scanning for PROFINET devices in CODESYS. The AM243 LaunchPad appears in the scan results, but the following error is reported: RPC Aborted: 0x16C9A049 Additionally, CODESYS shows the message that the identification data is not available and the IP address should be checked. Because of this error, the controller cannot establish a connection to the device. Another observation is that I cannot ping the AM243 LaunchPad from my PC, even though I configured what should be the correct IP address. Setup: PROFINET Device: AM243 LaunchPad PROFINET Stack: Industrial Communication SDK example PROFINET Controller: Raspberry Pi running CODESYS with PROFINET Runtime Engineering PC: CODESYS IDE Network: Ethernet connection between PC, Raspberry Pi, and AM243 In the attachments there is a screenshot of the corresponding error. Did anybody had the same error? Any hints or debugging suggestions would be greatly appreciated. Thank you!
Last updated: 2026-03-13

Post by hannibal on Codesys Trend - setting Y axis minimum and maximum as variables - error ^{CODESYS Forge talk (Post)}
Hi, It was my fault. I was using a REAL variable instead of INTEGER. Sorry for posting this.
Last updated: 2026-03-22

Post by gseidel on Smooth path is not working with SMC_NCInterpreter ^{CODESYS Forge talk (Post)}
Hi tommyk-mar, do you call SMC_SmoothPath after SMC_NCIntepreter? Both G51 in the G-Code and the function block call are needed. You can see how this can be done in this example: https://content.helpme-codesys.com/en/CODESYS%20SoftMotion/_sm_example_cnc_3.html Best regarsd, Georg
Last updated: 2026-03-27

Post by nulltrace on How change Unity-ID in TCP Modbus Slave ^{CODESYS Forge talk (Post)}
Hey Husarz. i don't forget you, the Thing is, to give you my answer, i have to wait for Answer from Codesys/E. Schwellinger. i suspect Mr. Schwellinger is on in Vacations that week. so please, be patient at moment
Last updated: 2026-04-10

Post by dim54 on Disabling automatic logout from the owner user ^{CODESYS Forge talk (Post)}
Hello! Please tell me how I can disable the automatic logout as the Owner user (CODESYS 3.5 SP15 Path 2). I have to reconnect multiple times during the workday. Thanks!
Last updated: 2026-01-16

Post by wollvieh on Sysfile Konfiguration ^{CODESYS Forge talk (Post)}
Hallo, nach Umstellung auf Raspberry Trixie sowie neueste CODESYS Version funktioniert das Schreiben Lesen mit Sysfile Bei mir nicht mehr. Zugriff bei Fileopen wird abgelehnt. Gibt es irgendwo eine Dokumentation, welche Einträge für Sysfile in der Datei CODESYSControl.cfg vorzunehmen sind? In Ratlosigkeit...
Last updated: 2026-01-19

Post by wollvieh on Sysfile Konfiguration ^{CODESYS Forge talk (Post)}
Hallo, nach Umstellung auf Raspberry Trixie sowie neueste CODESYS Version funktioniert das Schreiben Lesen mit Sysfile Bei mir nicht mehr. Zugriff bei Fileopen wird abgelehnt. Gibt es irgendwo eine Dokumentation, welche Einträge für Sysfile in der Datei CODESYSControl.cfg vorzunehmen sind? In Ratlosigkeit...
Last updated: 2026-01-19

Post by wollvieh on Sysfile Konfiguration ^{CODESYS Forge talk (Post)}
Hallo, nach Umstellung auf Raspberry Trixie sowie neueste CODESYS Version funktioniert das Schreiben Lesen mit Sysfile Bei mir nicht mehr. Zugriff bei Fileopen wird abgelehnt. Gibt es irgendwo eine Dokumentation, welche Einträge für Sysfile in der Datei CODESYSControl.cfg vorzunehmen sind? In Ratlosigkeit...
Last updated: 2026-01-19

Post by wollvieh on (no subject) ^{CODESYS Forge talk (Post)}
Hallo, nach Umstellung auf Raspberry Trixie sowie neueste CODESYS Version funktioniert das Schreiben Lesen mit Sysfile Bei mir nicht mehr. Zugriff bei Fileopen wird abgelehnt. Gibt es irgendwo eine Dokumentation, welche Einträge für Sysfile in der Datei CODESYSControl.cfg vorzunehmen sind? In Ratlosigkeit...
Last updated: 2026-01-19

Post by wollvieh on Sysfile Konfiguration ^{CODESYS Forge talk (Post)}
Hallo, nach Umstellung auf Raspberry Trixie sowie neueste CODESYS Version funktioniert das Schreiben Lesen mit Sysfile Bei mir nicht mehr. Zugriff bei Fileopen wird abgelehnt. Gibt es irgendwo eine Dokumentation, welche Einträge für Sysfile in der Datei CODESYSControl.cfg vorzunehmen sind? In Ratlosigkeit...
Last updated: 2026-01-19

Post by wollvieh on Sysfile Konfiguration ^{CODESYS Forge talk (Post)}
Hallo, nach Umstellung auf Raspberry Trixie sowie neueste CODESYS Version funktioniert das Schreiben Lesen mit Sysfile Bei mir nicht mehr. Zugriff bei Fileopen wird abgelehnt. Gibt es irgendwo eine Dokumentation, welche Einträge für Sysfile in der Datei CODESYSControl.cfg vorzunehmen sind? In Ratlosigkeit...
Last updated: 2026-01-19

Post by wollvieh on Sysfile Konfiguration ^{CODESYS Forge talk (Post)}
Hallo, nach Umstellung auf Raspberry Trixie sowie neueste CODESYS Version funktioniert das Schreiben Lesen mit Sysfile Bei mir nicht mehr. Zugriff bei Fileopen wird abgelehnt. Gibt es irgendwo eine Dokumentation, welche Einträge für Sysfile in der Datei CODESYSControl.cfg vorzunehmen sind? In Ratlosigkeit...
Last updated: 2026-01-19

Post by gseidel on SMC_Trafo 6DOF Config Error ^{CODESYS Forge talk (Post)}
Hi jgalaska, the parameters and their valid ranges are described here (0). In particular, the parameter d1 must be non-positive (<= 0). (0) https://content.helpme-codesys.com/en/CODESYS%20SoftMotion/_sm_trafo_pou_six_dof_robot.html#UUID-5451338b-a728-5c42-0f62-d9735b01d032_id_b18ea4b1b308acfdc0a8646358edc019_id_e7016982df408f59c0a8657d017550b3 Best regards, Georg
Last updated: 2026-01-21

Post by ketanvaishnav on Redundancy Codesys Runtime, Synchronization ^{CODESYS Forge talk (Post)}
i am facing same data sync issue. i am use two 750-8212 (FW30) controllers. datas are sync from active to standby during changeover time, but datas are not sync from standby to active.
Last updated: 2026-01-30

Post by mrkm-dic on CODESYS: Combining Master Redundancy with EtherCAT Ring Topology – Is it Supported? ^{CODESYS Forge talk (Post)}
Hello, I would like to ask whether it is technically supported (and practically achievable) to combine CODESYS Master Redundancy with EtherCAT ring (loop) redundancy in the same system. System setup CODESYS version: CODESYS 3.5.21.40 CODESYS Control SL for Weidmuller u-OS-4.12.2.0 Controllers (Masters): Weidmuller UC20-M4000 ×2, configured as Active / Standby using CODESYS redundancy EtherCAT Slaves: Weidmuller UR20-FBC-EC ×3, supporting EtherCAT ring / line break detection Topology: EtherCAT ring (loop) Main question Is it officially supported to use: ・CODESYS PLC/Master redundancy (Active/Standby) and ・EtherCAT ring topology (for cable redundancy) at the same time? Expected behavior Our expectation is: ・When the Active PLC fails, the Standby PLC becomes Active ・The Standby PLC then takes over the role of EtherCAT Master ・EtherCAT communication is re-established ・I/O control continues after reinitialization (a short interruption is acceptable; no strict bumpless requirement) We do not expect completely seamless / zero-cycle switchover, but we want to understand: ・Whether this combination is supported by design ・Or whether there are known limitations or restrictions when EtherCAT ring mode is used together with Master redundancy Clarification At this stage, the question is mainly about feasibility and support, not about a specific error message yet. Any official guidance, limitations, or real-world experience would be greatly appreciated. Thank you in advance.
Last updated: 2026-02-05

Post by risele on AI + Programming ^{CODESYS Forge talk (Post)}
It's already fine to use, with help of exporting/importing as PLC_Open, at least CODEX is good in editing directly at XML and/or providing changes description separately.
Last updated: 2026-02-13

Post by risele on CODESYS and Github Copilot ^{CODESYS Forge talk (Post)}
You actually can use copilot by PLCOpen XML file exporting/importing. It's fine to work with it directly (at least, the Codex do it quite well).
Last updated: 2026-02-13

Post by pernockham on Unable to deploy "Control for Linux SL 4.18.0.0" ^{CODESYS Forge talk (Post)}
Downloaded and installed edge gateway 4.19.0.0. Unfortunately same behavior: "Control for Linux SL" NOT shown in drop lists on either "Deployment" Tab of tool "Deploy Control SL", or as "installed packages" on "Operation" tab (only "CODESYS Edge Gateway for linux" is shown).
Last updated: 2026-02-16

Post by pernockham on Unable to deploy "Control for Linux SL 4.18.0.0" ^{CODESYS Forge talk (Post)}
Am I alone in this? Is this a known fault? Should I look for the reason of the lacking update option for "Control for linux SL" in my system or is it a potential fault in the codesys system?
Last updated: 2026-02-17

Post by eschwellinger on Unable to deploy "Control for Linux SL 4.18.0.0" ^{CODESYS Forge talk (Post)}
can you please check this: https://content.helpme-codesys.com/en/CODESYS%20Control/_rtsl_toubleshooting_deploytool2.html#UUID-b83dc01e-8cff-c574-7efe-8615b95a51ed_section-idm234790234401598
Last updated: 2026-02-19

Post by timvh on Unit testing support / libraries for EcoStruxure Machine Expert (CODESYS) ^{CODESYS Forge talk (Post)}
If the Professsional Developer Edition (which includes the Test Manager) is not supported by Schneider, then an option is to use the Open Source Unit test framework. See: https://forge.codesys.com/lib/counit/home/Home/
Last updated: 2026-02-20

Post by alexgooi on Codesys KNX implementation ^{CODESYS Forge talk (Post)}
Dear Forum, For anyone interested we have solved this problem. Before we were using a KNX TP/IP interface, now we are using a KNX TP/IP router, and it works like a charm now.
Last updated: 2026-03-04

Post by oemcba on Editor FIND highlight color ^{CODESYS Forge talk (Post)}
Today is 2026, and we still have the same issue since 2017, anyone have the answer? i'm using V3.5 SP18 P4+ from festo, thanks in advance... @rudolsto @r.evbatyrov @cole @mahmutonx @root @codesys-com
Last updated: 2026-03-06

Sort by relevance or date