Post by mtorell on Safe Editor in codesys v3.5sp21p30 ^{CODESYS Forge talk (Post)}
How do I negate an output signal from an OR gate. I have tried right click to no avail and I cannot find an propriate NEGATE box? I want to save the output from the block to an inverted variable.
Last updated: 2026-03-12

Post by mjam04 on AM243 LaunchPad as PROFINET Device with CODESYS – RPC Aborted error when scanning devices ^{CODESYS Forge talk (Post)}
Hello, I am currently trying to use the AM243 LaunchPad as a PROFINET device and connect to it using CODESYS. In my setup I am also using a Raspberry Pi running the CODESYS PROFINET Runtime, which acts as the PROFINET controller. The setup of the Profinet controller is correct, so all devices are in the same subnet. However, I encounter an issue when scanning for PROFINET devices in CODESYS. The AM243 LaunchPad appears in the scan results, but the following error is reported: RPC Aborted: 0x16C9A049 Additionally, CODESYS shows the message that the identification data is not available and the IP address should be checked. Because of this error, the controller cannot establish a connection to the device. Another observation is that I cannot ping the AM243 LaunchPad from my PC, even though I configured what should be the correct IP address. Setup: PROFINET Device: AM243 LaunchPad PROFINET Stack: Industrial Communication SDK example PROFINET Controller: Raspberry Pi running CODESYS with PROFINET Runtime Engineering PC: CODESYS IDE Network: Ethernet connection between PC, Raspberry Pi, and AM243 In the attachments there is a screenshot of the corresponding error. Did anybody had the same error? Any hints or debugging suggestions would be greatly appreciated. Thank you!
Last updated: 2026-03-13

Post by hannibal on Codesys Trend - setting Y axis minimum and maximum as variables - error ^{CODESYS Forge talk (Post)}
Hi, It was my fault. I was using a REAL variable instead of INTEGER. Sorry for posting this.
Last updated: 2026-03-22

Post by nulltrace on How change Unity-ID in TCP Modbus Slave ^{CODESYS Forge talk (Post)}
Hey Husarz. i don't forget you, the Thing is, to give you my answer, i have to wait for Answer from Codesys/E. Schwellinger. i suspect Mr. Schwellinger is on in Vacations that week. so please, be patient at moment
Last updated: 2026-04-10

Post by reinier-geers on Draw nails pattern ^{CODESYS Forge talk (Post)}
Hi I want to draw a nailpattern. But codesys Hasnt a draw command. And i dont want to draw 1000 nails and move them in position. Any one an idee ?
Last updated: 2026-04-20

Post by timvh on Alarmmanagement – Dynamic Alarm List ^{CODESYS Forge talk (Post)}
Probably best to create an alarm template for your motor function block. Then automatically the alarm manager can be filled with all the alarms for all instances of the motor function blocks (based on the created alarm template). See: https://content.helpme-codesys.com/en/CODESYS%20Visualization/_cds_obj_alarm_group_template.html
Last updated: 2026-04-25

Post by osande on V3.5 SP22 Patch1 ^{CODESYS Forge talk (Post)}
... and SP21 P6 also. Kind of bummer, migrating from TIA Portal to Codesys for PLC educational courses. These kind of bugs, and other deficiencies, really makes me regret my choice.
Last updated: 2026-05-06

Post by kiranbsiddaiah on CodeSys OPC UA client Unable to Connect To OPC UA sever through Username and password ^{CODESYS Forge talk (Post)}
And also we do not have any opc ua related license . Do we need to have a opc ua license to communicate with OPC UA server with username and password?
Last updated: 2026-05-07

Post by saml on Eaton HFX Controllers ^{CODESYS Forge talk (Post)}
Hellow every one. DPguy could do you share how you resolved the issues? what Codesys version did you used to fix it? thank a lot!!!
Last updated: 2026-05-26

Post by saml on Eaton HFX Controllers ^{CODESYS Forge talk (Post)}
Hellow every one. DPguy could do you share how you resolved the issues? what Codesys version did you used to fix it? thank a lot!!!
Last updated: 2026-05-26

Post by cm1435 on too much data for the controller ^{CODESYS Forge talk (Post)}
When I download project to ifm CR2530 controller, met the error "too much data for the controller". Actually my project is just 70k Bytes, far from the memory 1M of CR2530. Anybony ever met this problem?
Last updated: 2026-05-30

Post by skribblio on Port instantiation of serial interface in WAGO PLC using Modb_L05.lib in CoDeSys v2.3 ^{CODESYS Forge talk (Post)}
I have to express my appreciation to you for the great read!! No question, I loved every part of it. I have you bookmarked to see the new stuff you post Skribbl IO
Last updated: 2026-06-11

Post by dim54 on Disabling automatic logout from the owner user ^{CODESYS Forge talk (Post)}
Hello! Please tell me how I can disable the automatic logout as the Owner user (CODESYS 3.5 SP15 Path 2). I have to reconnect multiple times during the workday. Thanks!
Last updated: 2026-01-16

Post by wollvieh on Sysfile Konfiguration ^{CODESYS Forge talk (Post)}
Hallo, nach Umstellung auf Raspberry Trixie sowie neueste CODESYS Version funktioniert das Schreiben Lesen mit Sysfile Bei mir nicht mehr. Zugriff bei Fileopen wird abgelehnt. Gibt es irgendwo eine Dokumentation, welche Einträge für Sysfile in der Datei CODESYSControl.cfg vorzunehmen sind? In Ratlosigkeit...
Last updated: 2026-01-19

Post by wollvieh on Sysfile Konfiguration ^{CODESYS Forge talk (Post)}
Hallo, nach Umstellung auf Raspberry Trixie sowie neueste CODESYS Version funktioniert das Schreiben Lesen mit Sysfile Bei mir nicht mehr. Zugriff bei Fileopen wird abgelehnt. Gibt es irgendwo eine Dokumentation, welche Einträge für Sysfile in der Datei CODESYSControl.cfg vorzunehmen sind? In Ratlosigkeit...
Last updated: 2026-01-19

Post by wollvieh on Sysfile Konfiguration ^{CODESYS Forge talk (Post)}
Hallo, nach Umstellung auf Raspberry Trixie sowie neueste CODESYS Version funktioniert das Schreiben Lesen mit Sysfile Bei mir nicht mehr. Zugriff bei Fileopen wird abgelehnt. Gibt es irgendwo eine Dokumentation, welche Einträge für Sysfile in der Datei CODESYSControl.cfg vorzunehmen sind? In Ratlosigkeit...
Last updated: 2026-01-19

Post by wollvieh on (no subject) ^{CODESYS Forge talk (Post)}
Hallo, nach Umstellung auf Raspberry Trixie sowie neueste CODESYS Version funktioniert das Schreiben Lesen mit Sysfile Bei mir nicht mehr. Zugriff bei Fileopen wird abgelehnt. Gibt es irgendwo eine Dokumentation, welche Einträge für Sysfile in der Datei CODESYSControl.cfg vorzunehmen sind? In Ratlosigkeit...
Last updated: 2026-01-19

Post by wollvieh on Sysfile Konfiguration ^{CODESYS Forge talk (Post)}
Hallo, nach Umstellung auf Raspberry Trixie sowie neueste CODESYS Version funktioniert das Schreiben Lesen mit Sysfile Bei mir nicht mehr. Zugriff bei Fileopen wird abgelehnt. Gibt es irgendwo eine Dokumentation, welche Einträge für Sysfile in der Datei CODESYSControl.cfg vorzunehmen sind? In Ratlosigkeit...
Last updated: 2026-01-19

Post by wollvieh on Sysfile Konfiguration ^{CODESYS Forge talk (Post)}
Hallo, nach Umstellung auf Raspberry Trixie sowie neueste CODESYS Version funktioniert das Schreiben Lesen mit Sysfile Bei mir nicht mehr. Zugriff bei Fileopen wird abgelehnt. Gibt es irgendwo eine Dokumentation, welche Einträge für Sysfile in der Datei CODESYSControl.cfg vorzunehmen sind? In Ratlosigkeit...
Last updated: 2026-01-19

Post by wollvieh on Sysfile Konfiguration ^{CODESYS Forge talk (Post)}
Hallo, nach Umstellung auf Raspberry Trixie sowie neueste CODESYS Version funktioniert das Schreiben Lesen mit Sysfile Bei mir nicht mehr. Zugriff bei Fileopen wird abgelehnt. Gibt es irgendwo eine Dokumentation, welche Einträge für Sysfile in der Datei CODESYSControl.cfg vorzunehmen sind? In Ratlosigkeit...
Last updated: 2026-01-19

Post by gseidel on SMC_Trafo 6DOF Config Error ^{CODESYS Forge talk (Post)}
Hi jgalaska, the parameters and their valid ranges are described here (0). In particular, the parameter d1 must be non-positive (<= 0). (0) https://content.helpme-codesys.com/en/CODESYS%20SoftMotion/_sm_trafo_pou_six_dof_robot.html#UUID-5451338b-a728-5c42-0f62-d9735b01d032_id_b18ea4b1b308acfdc0a8646358edc019_id_e7016982df408f59c0a8657d017550b3 Best regards, Georg
Last updated: 2026-01-21

Post by eschwellinger on The element of type 'VisuFbElemImage' could not be updated. Reason: Index was outside the bounds of the array. ^{CODESYS Forge talk (Post)}
check with the CODESYS Installer er if you are on latest Visuversion. 4.9.1.0
Last updated: 2026-01-27

Post by ketanvaishnav on Redundancy Codesys Runtime, Synchronization ^{CODESYS Forge talk (Post)}
i am facing same data sync issue. i am use two 750-8212 (FW30) controllers. datas are sync from active to standby during changeover time, but datas are not sync from standby to active.
Last updated: 2026-01-30

Post by mrkm-dic on CODESYS: Combining Master Redundancy with EtherCAT Ring Topology – Is it Supported? ^{CODESYS Forge talk (Post)}
Hello, I would like to ask whether it is technically supported (and practically achievable) to combine CODESYS Master Redundancy with EtherCAT ring (loop) redundancy in the same system. System setup CODESYS version: CODESYS 3.5.21.40 CODESYS Control SL for Weidmuller u-OS-4.12.2.0 Controllers (Masters): Weidmuller UC20-M4000 ×2, configured as Active / Standby using CODESYS redundancy EtherCAT Slaves: Weidmuller UR20-FBC-EC ×3, supporting EtherCAT ring / line break detection Topology: EtherCAT ring (loop) Main question Is it officially supported to use: ・CODESYS PLC/Master redundancy (Active/Standby) and ・EtherCAT ring topology (for cable redundancy) at the same time? Expected behavior Our expectation is: ・When the Active PLC fails, the Standby PLC becomes Active ・The Standby PLC then takes over the role of EtherCAT Master ・EtherCAT communication is re-established ・I/O control continues after reinitialization (a short interruption is acceptable; no strict bumpless requirement) We do not expect completely seamless / zero-cycle switchover, but we want to understand: ・Whether this combination is supported by design ・Or whether there are known limitations or restrictions when EtherCAT ring mode is used together with Master redundancy Clarification At this stage, the question is mainly about feasibility and support, not about a specific error message yet. Any official guidance, limitations, or real-world experience would be greatly appreciated. Thank you in advance.
Last updated: 2026-02-05

Post by risele on AI + Programming ^{CODESYS Forge talk (Post)}
It's already fine to use, with help of exporting/importing as PLC_Open, at least CODEX is good in editing directly at XML and/or providing changes description separately.
Last updated: 2026-02-13

Sort by relevance or date