Post by andrax on Meine Gerätesammlung basierend auf TCA9548 ^{CODESYS Forge talk (Post)}
Hallo zusammen, ich programmiere öfters mal kleinere Messgeräte und Datenlogger. Je nach Einsatzzweck musste ich mir ein paar Gerätetreiber selber schreiben. Da es eine recht große Sammlung ist, stelle ich die hier einfach mal ein. Die Sammlung basiert auf den Gerätetreiber TCA9548 Multiplexer von Steffen Dreyer. Codesysversion: V3.5 SP18 Patch 4 Inhalt: -4channel Dimmer (Stefan Dreyer) -BMA456 (Andre Klien) -BME280 (Stefan Dreyer) -BMP280 (Stefan Dreyer) -EEPROM_24C512 (Stefan Dreyer) -ADS1115 (Andre Klien) -ICP10125 (Andre Klien) -PCA9555 (Stefan Dreyer) -PCA9685 (Stefan Dreyer) -PCF8575 (Stefan Dreyer) -SDP810 (Andre klien) -SSD1306 (Stefan Dreyer) -TCA9548 (Stefan Dreyer) -TSL2561 (Stefan Dreyer) Alle Gerätetreiber laufen über den Multiplexer, können aber auch ohne betrieben werden. Einschränkung: BMA456: Die Konfigurationsdaten werden erfolgreich in den Chip geschrieben, dieser meldet aber config wrong. Warum auch immer, der Sensor funktioniert und bringt hochempfindlich Beschleunigungsdaten. ADS1115: Hie habe ich nur die wichtigsten funktionen implementiert. 1-4 Kanäle, PGA, kontinuierlicher Modus, Datenrate. Alle anderen Funktionen (single-shot, komparator,alm) sind nicht implementiert. Das macht auch keinen Sinn, da diese Funktionen besser über die Steuerung realisiert werden können. Achtung beim ADS1115 ist zwingend ein Levelshifter notwendig, wenn ihr diesen mit 5V betreiben wollt. Ihr grillt sonst euren Raspi (SDA, SCL sind dann 5V) Gruß Andre
Last updated: 2023-12-18

Post by mavitia on Application based license problem - Modbus TCP ^{CODESYS Forge talk (Post)}
I am running ubuntu on a raspberry pi, and installed an application based license Control Basic M on it, it runs a demo program fine, does not timeout etc. however, when I add a modbus TCP device, I start getting errors: <Entry severity="error" component="CmpApp" user="nobody" timestamp="12/18/2023 3:49:42 PM" infoId="24">Online change denied. Application Application is in exception state!</Entry> <Entry severity="error" component="CmpApp" user="nobody" timestamp="12/18/2023 3:49:42 PM" infoId="68">Download failed: Application=Application</Entry> <Entry severity="exception" component="CmpApp" user="nobody" timestamp="12/18/2023 3:49:41 PM" infoId="0">Application app=Application has invalid license metrics!</Entry> the modbus tcp slave runs, and the counter ticks up, however, when I call the variables on the %IX0.0 in my program, and try to upload the changes, I am getting the error messages which stop the program as far as I understand, the application based, M includes 2 fieldbus instances, but on the other side is fairly new, anything obvious I am missing out here?
Last updated: 2023-12-18

Post by spiessli on Softmotion axis to CANopen Maxon IDX drive ^{CODESYS Forge talk (Post)}
Thanks for the advise, indeed, this was somewhat, what my intention was. I tried around again with EDSes and DCFs, anyway. It appears that the DCFs end up in a subfolder in the attach device dialog. Astonishingly, when attaching the DCF version I get a device in the device tree, where I can add a SoftMotion axis, whereas when I attach the device not in the subfolder, then I cannot. Further astonishingly, when looking in the CANopen parameters in supported profiles, "402" is listed in the case of the DCF variant, whereas in the EDS variant "0" is shown. Comparing EDS and DCF files I cannot guess, where the difference is coming from. I cannot tell either why I have always attached the EDS variant and apparantly never the DCF variant. As I am not in the lab right now, I cannot test if the connection actually is working. Thanks again, spiessli
Last updated: 2024-01-07

Post by edepalos on Text list from sd card ^{CODESYS Forge talk (Post)}
Hi guys, I have a textlist in my project which is working just as expected in a drop down list. I would like to move this text list to a sd card and access it from there, because I want to ease the editing of the contents of this textlist. I'm imagining a solution like the operator shuts down the plant, takes the sd card out, edits the textlist on the card with a windows machines notepad, then reinserts the card in the PLC and restarts the plant, having the new content of the textlist populating the dropdown list. I'm sorry that I'm asking you to spoonfeed me, but I did not find anything straightforward to do this... I saw in the Project>Project settings>Visualisation a relative path thingy, but I have the plant in operation and I would not like to make 100 trial and errors right now... I'm also not interested in SysLib file read commands and stuff, I would just like to access the file from the cards part, I don't want to replace its contents dynamically or such... nor I have language files or recipes... Thank You in advance! Br, Ede
Last updated: 2024-01-16

Post by mondinmr on Direct Pointers in IOMapping for EtherCAT with IoDrvEthercatLib.ETCSlave_Dia ^{CODESYS Forge talk (Post)}
Using SDO, I can read the EtherCAT mappings and offsets from various registers like 0x1c12, 0x1c13, etc. When I obtain registers mapped in the PDOs and various offsets, I could technically access directly to the statusword, controlword, etc., if they are mapped. I have noticed that on IoDrvEthercatLib.ETCSlave_Diag I can find pointers to the input and output buffers. However, although the input buffer can be easily read by referring to what has been obtained from the SDOs, it is not possible to write to the output buffer, as it is overwritten in each cycle by the data from the IOMapping task. Is there a way, knowing an instance of IoDrvEthercatLib.ETCSlave_Diag, to obtain the pointer to the first data in the IOMapping? The offsets are identical to those of the PDOs, but obviously the data is a copy. For me, the cleanest thing would be to access the pointers on IOMapping, for DS402a devices to retrieve the key data and point them to internal references. I need to know this as, having developed our own motion library, I would like to simplify the initial setup by eliminating unnecessary and nonsensical mappings that can lead users to unnecessary errors. In the current version that we have been using for years, we have to map everything manually. I would like to pass only the slave reference to the FB_init constructors and eliminate the mapping.
Last updated: 2024-02-12

Post by dtamm on How to read string from CharBufferPtr? ^{CODESYS Forge talk (Post)}
I am trying to implement a mechanism to send alarm SMS. For this, I have created an Alarm Class with a Notification Action which calls a POU. This POU implements IAlarmNotifiable making it selectable in the Alarm Class configuration. IAlarmNotifiable has an Execute method which is called by the alarm class. Now, I want to extract the alarm message of the triggered alarm. The Execute method comes with a VAR_INPUT itfAlarm: AlarmManager.IAlarm which supplies a method called GetMessage. The help text says: Returns the message text, that has been configured for the alarm. The result is a pointer to the buffer, where the message text is stored The type of the result is CharBufferPtr, and at some place I read that it can be interpreted as a pointer to string. But I cannot manage to extract the alarm message, all I get are numbers. I have tried the following: psAlarmText := itfAlarm.GetMessage(__SYSTEM.TYPE_CLASS.TYPE_STRING)^; sAlarmText := TO_STRING( itfAlarm.GetMessage(__SYSTEM.TYPE_CLASS.TYPE_STRING)^ ); So how do I get access to the alarm message as clear text? (In this case, "Larm 1")
Last updated: 2024-02-21

Post by mtho on JSON Utilities - JSON file written with invalid structure ^{CODESYS Forge talk (Post)}
I'm using the JSON Utilities SL library to write configurations in my program to a file. I'm generating the JSON data using the builder function block and all appears to work correctly. When I write the jsondata to file, I'm finding that some of the JSON elements are not being written in the right location in the file. Rather than writing they keys under the parent object, they get written outside the root JSON object at the end of the file. If I then try to read the file back into the program, I get an invalid_structure error. I don't get any errors when populating the JSON data or when writing the file. I attached an example of the JSON writer output. The problems begin with key P200. Each P200 should go under MBR1 through MBR3. Among the rest of the keys, they are supposed to be under different parent objects. I am using default values for wsLineBreak and encoding.
Last updated: 2024-03-06

Post by manuknecht on High Cycle Times for SoftMotion_PlanningTask when using AxisGroup ^{CODESYS Forge talk (Post)}
Hello all I am using an AxisGroup with the Gantry2 Kinematics to move a 2D-Gantry system. When creating the AxisGroup, the SoftMotion_PlanningTask is created automatically with a cycle time of 2 ms in my case. I realized that the maximum cycle time of this task can spike to very high values (up to 60 ms) at lower speeds of the motion, leading to synchronization issues and errors on the axes. The same behaviour - though not as drastic - can be observed with virtual axes too. Is this behaviour intended or to be expected? Can the cycle time or type of the SoftMotion_PlanningTask be changed to prevent these errors? Or is there another fix for this issue? I tried changing the cycle type to Freewheeling, which solved the synchronization issues, but caused an error on the AxisGroup after a while, reading SMC_CP_QUEUE_UNDERRUN. Thanks in advance and best regards Manuel
Last updated: 2024-03-07

Post by acc00 on Main Task cycle too long leading to PLC Fail ^{CODESYS Forge talk (Post)}
I have 2 Wago PFC200 PLC, running with Runtime SP19 Patch 5, with the Redundant application. The PLC communicates as Modbus Master with at this moment 15 Modbus Slaves -later there will be 28 in total- (Drives, Power management units,...). These devices are connected in 2 rings (1 ring of Drives, 1 ring of Power Management units), with 2 Managed Moxa Switches being part of the ring. Each PLC is connected to one of these switches. The issue I'm encountering is that the Cycle time of the Active PLC goes very high when I'm closing the Drive ring (simulating an issue on one Cabinet supply, resulting in that one Drive shut down, which can happen on field quite often). As a result of this long cycle, the PLC fails and goes to Exception, and the Passive PLC does not take control of the system. A normal cycle is around 30ms for the Main task, and a few ms for the Ethercat task. When I monitor with Profiler, I see that in this Maximum Cycle, the main Task is only taking 13ms, so I'm not sure where the PLC is hanging for so long. Is the remaining cycle time the Redundant management/sync or something else? Thank you in advance.
Last updated: 2024-03-08

Post by wbj0t on mobus tcp slave device. read/write holdings with 2 variables. ^{CODESYS Forge talk (Post)}
Hi there. I have an issue to read and set time for the controller. In the issue many registers described as writable by 6/16 functions, and, in this time, also(!) readable! For example: I have time registers: min, hour, day, mon, year. By specifications it is possible check time (so I need always update these varibles in loop) and set time by writing these same registers, BUT how to set, if they will immediatle updated by current time after writing? So, I need to separate one address at two variables. I have seen option mark: Overlay of the process image by the holding and input register. I understand this so: When I READ by function 3, I will get variable that connected with the same INPUT address and when I WRITE by 6/16 this will change second variable that connected with HOLDING address. BUT, this mark doesnt work, when I write 6/16 and try to get by function 3, I will get written value instead INPUT variable. So, what to do?
Last updated: 2024-03-20

Post by squiggleypuff on Can't Add New Version of Modbus TCP Master ^{CODESYS Forge talk (Post)}
I'm having a tough time trying to get Modbus working on a Festo CPX-E PLC; it throws these pre-compiler errors as soon as I add in my Modbus TCP Master 3.5.12.30 to my project: I'm confused about the C0046 error, as I have IODrvModbusTCP 4.3.0.0 Library installed. So I thought maybe I needed to use the newest Modbus TCP Master 4.3.0.0, which is in my device repository: However, whenever I go to add this underneath the Ethernet adapter (which is version 4.2.0.0), the only TCP Master version available is the old 3.5.12.30 one, even if I have Display all versions checked.: I even went so far as to delete the old version, but then there were no options to add a Modbus TCP Master under my Ethernet adapter. What needs to be done to use the newest Modbus TCP Master? Or are these pre-compiler errors unrelated and I'm missing something? Any help greatly appreciated.
Last updated: 2024-04-04

Post by tim-roelant on Problem mit control runtime V3 und profinet ^{CODESYS Forge talk (Post)}
Hallo Edwin, meinst du das der control-win nicht wie SPS verwendet werden kann? Das program ist klein, und realtime brauch ich gar nicht, Es gibt im bus einem Turck inselstation mit 16 ein und ausgange, und ein MTS linearencoder, womit wir teile messen und abschneiden. Die cycluszeit reist auch nicht aus. Processorleisung bleibt unter 20%. Es geht mir darum das der profinet master in fehler geht, und nicht mehr seine telnehmer erkannen kann. Es kan passieren nach 10 minuten, aber auch nach 5 tage. Nur ein kaltstart bringt die bus wieder am laufen. (kein reconnect mochlich, auch die bus scannen functioniert nicht mehr) Wann ich aber ein ipscan durchfure mit Angryip auf der rechner sind alle telnehmer da. Ich habe noch eine andere application mit die gleiche anwendung, aber wo ein raspberry pi die SPS rolle spielt, und das functioniert einwandfrei. Soll ich fielleicht das OS von Rechenr nach linux umrusten? Der operator ist im moment sehr unzufrieden mit die "upgrade" von maschine... :-( lg Tim
Last updated: 2024-04-11

Post by tim-roelant on Problem mit control runtime V3 und profinet ^{CODESYS Forge talk (Post)}
Hallo Edwin, meinst du das der control-win nicht wie SPS verwendet werden kann? Das program ist klein, und realtime brauch ich gar nicht, Es gibt im bus einem Turck inselstation mit 16 ein und ausgange, und ein MTS linearencoder, womit wir teile messen und abschneiden. Die cycluszeit reist auch nicht aus. Processorleisung bleibt unter 20%. Es geht mir darum das der profinet master in fehler geht, und nicht mehr seine telnehmer erkannen kann. Es kan passieren nach 10 minuten, aber auch nach 5 tage. Nur ein kaltstart bringt die bus wieder am laufen. (kein reconnect mochlich, auch die bus scannen functioniert nicht mehr) Wann ich aber ein ipscan durchfure mit Angryip auf der rechner sind alle telnehmer da. Ich habe noch eine andere application mit die gleiche anwendung, aber wo ein raspberry pi die SPS rolle spielt, und das functioniert einwandfrei. Soll ich fielleicht das OS von Rechenr nach linux umrusten? Der operator ist im moment sehr unzufrieden mit die "upgrade" von maschine... :-( lg Tim
Last updated: 2024-04-11

Post by timo on Visu: Angepasster Button mit Statusanzeige - welche Möglichkeiten gibt es? ^{CODESYS Forge talk (Post)}
Hallo, Ich gehe gerade Möglichkeiten durch, wie ich Buttons so erstellen kann, dass ich sie nachträglich möglichst einfach bearbeiten kann um z.B. die Farben des Aktiven/Inaktiven Zustandes darzustellen. Die Buttons bestehen aus einem Hintergrund als Farbverlauf, einem Text und einem Icon. Ich habe zuerst den ESC Image Button verwendet, aber auch hier müsste ich nacheinander alle Buttons bearbeiten, wenn ich z.B. die Hintergrundfarbe anpassen will. Jetzt habe ich die Buttons als einzelne Visualisierungen erstellt und in der Visu jeweils als Frames eingeblendet. Den Zustand kann ich dann durch unsichtbare Elemente in der Buttonvisu darstellen. Weil hinter jeder Buttonvisu ein Frame meines Hintergrundes liegt, kann ich die einfach anpassen. Siehe Bild- der Frame ist der graue Hintergrund, das Rechteck ist die Umrandung für den Status mit einer transparenten Füllfarbe. Gibt es da eine einfachere Möglichkeit die Elemente zu verknüpfen, sodass ich einen Button habe, den ich nachträglich möglichst einfach abändern kann? Bei den Buttons bei denen ich keine Icons einblende, kann ich direkt den Text auf den Hintergrundframe setzen. Wenn ich hier aber das farbige Randungsrechteck für den Status über das Frame liege, verdeckt es diesen natürlich. Gibt es eine Möglichkeit Elemente so einzublenden, dass dahinter liegende Elemente angeklickt werden können? Alternativ muss ich die Aktion auch noch mit dem überlagertem Element verknüfen.
Last updated: 2024-04-22

Post by phoward131 on Alarm State Icon ^{CODESYS Forge talk (Post)}
I am trying to create an icon on an overview screen that depicts if an alarm group has active alarms, active acknowledged alarms, or inactive unacknowledged alarms (waiting for confirmation). I've attempted to set up Notification Actions in the Alarm Class to set variables based on state changes but have been unable to find a clean and effective way to do this. Because an action on any alarm will trigger the variable to be set as instructed, I'm struggling to find a way to configure it for what I need (ie if two alarms activate, then one deactivates, the variable for indicating an alarm is active would be cleared after the single deactivation). I've been pointed toward the Alarm Manager example project but I'm finding it too complicated to understand how to implement it in my own project. Has anyone come up with another good way to indicate the states of alarms or a simpler usage of the Alarm Manager functions?
Last updated: 2024-04-23

Post by culius on JSON ^{CODESYS Forge talk (Post)}
Hey guys, I am trying to write a JSON. First time after login in PLC after download everthing works. But when I want to change values during runtime and try to recreate the JSON nothing happens. When forcing the xStart as an impulse i want to recreate it and see 2 as Key3 instead of 1 from the first run. Any Idea how to make this work? PROGRAM test VAR factory : JSON.JSONDataFactory; eDataFactoryError : JSON.FBF.ERROR; pJsonData : POINTER TO JSON.JSONData := factory.Create(eError => eDataFactoryError); fb_JBuilder : JSON.JSONBuilder; wsValue : WSTRING; diRootIndex, diObject1Index : DINT; iValue : INT; jsonArrayWriter : JSON.JSONByteArrayWriter; wsJsonData : WSTRING(1000); xFirst : BOOL := TRUE; END_VAR IF xFirst THEN fb_JBuilder(pJsonData := pJsonData, diRootObj => diRootIndex); wsValue := "Value1"; fb_JBuilder.SetKeyWithValue("Key1", wsValue, diParentIndex := diRootIndex); diObject1Index := fb_JBuilder.SetKeyWithObject("Key2", diParentIndex := diRootIndex); iValue := iValue + 1 ; // -----------!!! secound run should increment key3!!!!------------ fb_JBuilder.SetKeyWithValue("Key3", iValue, diParentIndex := diObject1Index); xFirst := FALSE; END_IF jsonArrayWriter(xExecute := TRUE, pwData := ADR(wsJsonData), udiSize := SIZEOF(wsJsonData), jsonData := pJsonData^, xAsyncMode := FALSE); Kind Regards
Last updated: 2024-04-30

Post by rmaas on Strange Behavior on Raspberry Pi ^{CODESYS Forge talk (Post)}
Hello, what you are seeing is not strange behavior. The problem is that everyting is happening in the same program cycle. After the variable Stepnumber is changed from 10 to 20 for example then you want the program to wait with the next EQ until the next program cycle. Else every EQ will be be true because in every line the variable Stepnumber is increased. When the program arrives (still in the same cycle) at the line with the timer, the Stepnumber has been increased to 30 in the meantime and the timer will allway be ON because even though the variable is written to 10 in this line in the next cycle it starts with 10 and will be 30 again before reaching the timer in line 8. Not very good at explaining stuff but i hope you get the problem. See screenshot below for an example of one way you could solve this...
Last updated: 2024-06-18

Post by svenkaro on Codesyscontrol.service stoppt nach 30s ^{CODESYS Forge talk (Post)}
Wie Du schon vermutet hast, es meint, die Hardware/Firmware sei nicht kompatibel ... ooops... this runtime was built for RASPBERRYPI. Hardware version or firmware version not supported! (-18, 0x00000BB8, 0xFFFFFFFB) Architecture: aarch64 Byte Order: Little Endian CPU(s): 4 On-line CPU(s) list: 0-3 Vendor ID: ARM Model name: Cortex-A72 Model: 3 Thread(s) per core: 1 Core(s) per cluster: 4 Socket(s): - Cluster(s): 1 Stepping: r0p3 CPU(s) scaling MHz: 40% CPU max MHz: 1500.0000 CPU min MHz: 600.0000 BogoMIPS: 108.00 Flags: fp asimd evtstrm crc32 cpuid Caches (sum of all): L1d: 128 KiB (4 instances) L1i: 192 KiB (4 instances) L2: 1 MiB (1 instance) Vulnerabilities: Gather data sampling: Not affected Itlb multihit: Not affected L1tf: Not affected Mds: Not affected Meltdown: Not affected Mmio stale data: Not affected Retbleed: Not affected Spec rstack overflow: Not affected Spec store bypass: Vulnerable Spectre v1: Mitigation; __user pointer sanitization Spectre v2: Vulnerable Srbds: Not affected Tsx async abort: Not affected Allerdings habe ich schon reichlich Firmware versionen getestet.
Last updated: 2024-06-21

Post by joachimk on Profinet Controller IP-Adresse ändern ^{CODESYS Forge talk (Post)}
Die IP-Adresse des Profinet-Controllers soll zur Laufzeit geändert werden. Dabei handelt es sich um eine Anwendung auf einem PC mit einer Standard-Ethernetschittstelle (ControlWinV3+WinPcap). Die Datei "CODESYSControl.cfg" wurde dazu angepasst: .... Adapter.0.Name="Ethernet 4" Adapter.0.EnableSetIpAndMask=1 Die konfigurierte IP-Adresse wird zur Laufzeit an die tatsächliche IP-Adresse der Netzwerkschnittstelle mit dem folgenden Befehl angepasst (die Änderung von 192.168.2.33 auf 192.168.2.34 funktioniert auch): Ethernet.UpdateConfiguredIPSettings(IpAddress:=Ethernet.IPAddress, subnetmask:=Ethernet.Subnetmask, gateway:=Ethernet.GatewayAddress); Der Profinet-Controller geht danach auf Störung und gibt die folgende Fehlermeldung aus: "Controller-Status: currently active IP does not match the controller's configuration" Unter "Ethernet diagnostic information" kann man die geänderte IP-Adresse von 192.168.2.34. Ethernet läuft auch ohne Fehler. Unter "PROFINET IO Driver diagnostic information" -> "IPParameter" sieht man noch die alte (konfigurierte) IP-Adresse 192.168.2.33. Wie kann man die Störung beseitigen? Leider habe ich keine Methode zum Ändern der IP-Adresse auf dem Profinet-Controller gefunden? Reconfiguration des Profinet-Controllers?
Last updated: 2024-06-27

Post by wbj0t on What the right way to update TCP/COM slave device holding registers ^{CODESYS Forge talk (Post)}
Hi all :) I have an plc. This plc has option to be as slave device. There are TCP -> Serial Slave Device and COM -> Serial Slave Device. There are 4096 ModBus holding registers with mark "internal modify" for the both devices above. So, COM Slave has 4096 registers and TCP Slave has 4096 registers. And, finally, I have an ARRAY[0..4095] OF WORD. This array glued with COM Slave and TCP slave. Yes, I need plc's opportunity to be communication both TCP and COM ways for the same registers. For example, the next task structure: * TASK_0: 1. pou_READ_Registers 2. pou_0 3. pou_1 4. ... 5. pou_N 6. pou_WRITE_Registers At the first pou I read registers for the other pous, after job we have sort of state of the plc. At the last pou (6) we write modified registers. It is a good scenario: some one wrote registers for the job, after job we save these (modified) registers. But, what if registers wrote between 1 and 6 pou by operator, for example, at the 3 pou -> the last pou 'pou_WRITE' will rewrite this request from operator. What the right way to work with this logic? Thanks you.
Last updated: 2024-07-01

Post by simone on Cannot connect to webvisu on localhost ^{CODESYS Forge talk (Post)}
As I wrote before on the title, I have difficulties to connect to see webvisu from localhost. The story: while waiting for the plc+hmi to arrive, I'm preparing the software, mainly the visual parts trough the control Win3 x64 (same version as the ide 3.5.20.10). The problem is that I can't see the webvisu with the installed webbrowser. I don't know if this is a problem, but I changed the port to 9001 (randomly "free") because 80, 8000, 8080, 8088, 3000 are all occupied by other projects (all on the Apache server). Is there something wrong with the config file? This is the url: localhost:9001/webvisu_app.htm and here the config file part "CmpWebServer". [CmpWebServer] ;The handling of startup/shutdown of the webserver: ;0->automatically start, shutdown only on shutdown of the runtime;1->automatically start, could be shutdown on demand ;2(default)->start/shutdown on demand;3->start on demand, shutdown only on shutdown of the runtime StartupType=0 ;The TCP port the webserver listens on WebServerPortNr=9001 LocalAddress=localhost ;LocalAdapterName=LAN-Connection LocalAdapterName=EthernetPCPLC ;LocalAdapterNameUnicode=L\00A\00N\00-\00C\00o\00n\00n\00e\00c\00t\00i\00o\00n\00 LocalAdapterNameUnicode=E\00t\00h\00e\00r\00n\00e\00t\00P\00C\00P\00L\00C\00 Thanks for all the help!
Last updated: 2024-07-11

Post by solve-it on SysFileOpenAsync ^{CODESYS Forge talk (Post)}
Just realized that it is the /dev/input/js0 file. Don't think this is a prob either. Found the ConfigFile. Where and how to add /dev/input/js0? raspberry [SysFile] FilePath.1=/etc/, 3S.dat PlcLogicPrefix=1 [SysTarget] TargetVersionMask=0 TargetVersionCompatibilityMask=0xFFFF0000 [CmpLog] Logger.0.Name=/tmp/codesyscontrol.log Logger.0.Filter=0x0000000F Logger.0.Enable=1 Logger.0.MaxEntries=1000 Logger.0.MaxFileSize=1000000 Logger.0.MaxFiles=1 Logger.0.Backend.0.ClassId=0x00000104 ;writes logger messages in a file Logger.0.Type=0x314 ;Set the timestamp to RTC [CmpSettings] FileReference.0=SysFileMap.cfg, SysFileMap FileReference.1=/etc/CODESYSControl_User.cfg [SysExcept] Linux.DisableFpuOverflowException=1 Linux.DisableFpuUnderflowException=1 Linux.DisableFpuInvalidOperationException=1 [CmpWebServer] ConnectionType=0 [CmpOpenSSL] WebServer.Cert=server.cer WebServer.PrivateKey=server.key WebServer.CipherList=HIGH [SysMem] Linux.Memlock=0 [CmpCodeMeter] InitLicenseFile.0=3SLicense.wbb [SysEthernet] Linux.ProtocolFilter=3 [CmpSchedule] ProcessorLoad.Enable=1 ProcessorLoad.Maximum=95 ProcessorLoad.Interval=5000 DisableOmittedCycleWatchdog=1 [CmpUserMgr] AsymmetricAuthKey=6873d655ac1f166f3743feea42d2f3dd1b39ae40 [CmpSecureChannel] CertificateHash=09fd8d52be4ddd45a709bc9c95e2aa093b3f5695 [SysSocket] Adapter.0.Name="eth0" Adapter.0.EnableSetIpMask=1 ;raspberry [ComponentManager] ;Component.1=CmpGateway ;Component.2=CmpGwCommDrvTcp ;Component.3=CmpGwCommDrvShm [SysCom] ;Linux.Devicefile=/dev/ttyS [CmpBlkDrvCom] ;Com.0.Name=MyCom ;Com.0.Baudrate=115200 ;Com.0.Port=3 ;Com.0.EnableAutoAddressing=1 [SysProcess] Command.0=shutdown [CmpApp] Bootproject.RetainMismatch.Init=1 ;Application.1=Application ;Application.1=Application ;Application.1=Application Application.1=Application [CmpRasPi] Architecture=armv6l [CmpRedundancyConnectionIP] [CmpRedundancy] [CmpSrv] [IoDrvEtherCAT]
Last updated: 2024-07-16

Post by grant32 on RAMP_REAL FB is retaining my output value when i try to re use the FB ^{CODESYS Forge talk (Post)}
Hello, I'm relatively new to PLC programming. I am trying to creat a ramp down function, I have an example here of what I am using. I can get the function to work, the issue is that the OUT (variable3) value is being held by the FB so after I use it once it no longer works. In this example i set variable3 to 100 and the rest is as seen, over the course of a minute it ramped down to 10 (as desired). But when I deenergize TEST_START, set variable3 back to 100, and then re-energize TEST_START it immediately jumps back to the previously held value 10. The reset on this block just pauses the function and holds the last OUT. In my case I will need the function to start OUT at a set value, ramp down to the IN (variable2) value, and then accept a new OUT value to ramp down next time the block is energized. Hopefully this made sense, if anyone has any advice that would be awesome!
Last updated: 2024-07-29

Post by mubeta on parker servo and position ^{CODESYS Forge talk (Post)}
In general, drives have parameter sets to adjust behaviour in such cases: position recovery, adaptation with resistant torque, out-of-position window failure, etc. (Much depends on the type of configuration set for the axis: positioner, speed controller, torque controller, etc.). I have used that type of drive very little, in only two cases and a long time ago. To tell you what is normal is impossible. I know by reputation they are very simple objects, without too many pretensions and adjustments possible. Try running traces by monitoring actual position, motor current, torque and following error. These are the most sensible curves to understand what is going on. Maybe by fine tuning the motor tuning, the current controller or the speed controller you will get something closer to what you want. For example, from DS, the motor has a standstill torque of 3 Nm. Observe with traces whether this is effective: motor current trend. And afterwards, when you have your own accurate picture of the situation, you can also hear from the product's local support to see if you can steal a few more things from it performance-wise.
Last updated: 2024-08-05

Post by abauza on Image Pool using in other libraries ^{CODESYS Forge talk (Post)}
Hi im Albert, im developing libraries for my PLCs and i have some issues on visualization part. First of all I have done a library that have a image pool with a list of 4 gifs "ImagePoolErrors" (i've tested in other projects and it works) but the problem comes when i create another library that in the visualization part contains images from my image pool library, when i simulate a program that includes a instance of my second library object the visualization images dont show, any of them, i've checked all the references and tried some options of the image properties but without any difference. Here is the screenshots of the first library (that contains Image Pool) and the second library (that includes images of the image pool first library) and the visualization simulation (with the missing image gif issue). Any idea of what i forgotten in the process? If you need any detail of the library or of the project or you need the library file, ask me, thank on advance
Last updated: 2024-08-19

Sort by relevance or date