Post by timo on Visualisierung: Tastatur vergrößern? ^{CODESYS Forge talk (Post)}
Hallo, Ich nutze den Stil White Style 3.5.16 mit ein paar farblichen Änderungen über den Stileditor. Was ich gerne machen würde, wäre die Tastaturen zu vergrößern, die sich auf dem Touchpanel öffnen wenn ein INT oder STRING eingegeben werden muss. Gibt es dafür "fertige" Variablen im Editor des Stils oder in Codesys selbst, mit dem die Größe hochskaliert werden kann? Oder muss ich jede Taste einzeln anpacken? Danke im Voraus :)
Last updated: 2025-02-21

Post by reiterf on Visualisierungs-Stil White style, 3.5.16.0 verursacht Überseztungsfehler ^{CODESYS Forge talk (Post)}
Hi, ich möchte ein kleine Testaufbau visualisieren und hätte mich für den Stil "White" entschieden. Nun ist es allerdings so, daß dieser Stiel einige Fehler beim übersetzen erzeugt. Ich habe dann versicht auf den Basic-Style zurückzugehen -- dann sind auch die Fehler weg. Leider wird dann auf der WebVisu (nur am Gerät) kein Druckknopf mehr angezeigt. Ich habe die gleichen Fehler auf 2 Codesys-Installationen (Gleicher Software Stand, 2 PCs) Kann mir da jemand weiterhelfen?
Last updated: 2025-02-27

Post by kuapiz on Camera RTSP Feed ^{CODESYS Forge talk (Post)}
Hello, I'm facing the same problem, I can access the FLIR AX Series camera through the IP converter software (go2rtc). In the CODESYS 3.5.19 patch 7 software, the streaming does not appear in the webvisu even using the URL "http://xxx.xxx.x.xxx:1984/stream.html?src=flirr". I used the "RTC" and "MJPG" modes. HW: PFC200 750-8217/600-000. FW: v27. If anyone has a solution, could you help us?
Last updated: 2025-03-05

Post by imdatatas on Problem of assigning physical addresses to variables of type ARRAY OF ARRAY as MW and QW ^{CODESYS Forge talk (Post)}
Hello, I am encountering an interesting problem as below in SP20patch5 variable definition area. I think this is a bug. As can be seen in the attached screenshot, it assigns the same %MW or %QW address to all elements of the array. I hope Codesys team can solve this problem in the next version. Best regards, Imdat
Last updated: 2025-03-17

Post by twofacexx on codesyscontrol.log exzessive Größe ^{CODESYS Forge talk (Post)}
Moin, kann es sein, dass dies auch schon wieder veraltet ist? Ich habe aktuell die 3.5 SP20 Patch 4 mit einem Paspberry 5 64bit SL am laufen und es wird leider nix geloggt. Muss man da etwas am Filter einstellen damit etwas geloggt wird? WÄre echt cool, wenn Codesys anfangen würde, Info´s in Form von Text einzupflegen....dann könnte man es auch nutzen. Brauche das Log bzgl. eines anderen Problems mit der "SysProcess.SysProcessExecuteCommand2", leider auch nicht gut kommentiert.
Last updated: 2025-03-18

Post by patrik on windows runtime crashes. ^{CODESYS Forge talk (Post)}
Faulting application name: CODESYSControlService.exe, version: 3.5.20.30, time stamp: 0x66ebc91d Faulting module name: unknown, version: 0.0.0.0, time stamp: 0x00000000 Exception code: 0xc0000005 Fault offset: 0x0000028010670e31 Faulting process id: 0x0x1F50 Faulting application start time: 0x0x1DB1BA284347B9C Faulting application path: C:\Program Files\CODESYS 3.5.20.30\GatewayPLC\CODESYSControlService.exe Faulting module path: unknown Report Id: d3ac6a03-667a-4d61-ab36-d2ae703fc252 Faulting package full name: Faulting package-relative application ID: My runtime crashes from time to time. I'm not getting anything in the PLC logs. This is from the windows logs. Can anyone help me understand why this is happening?
Last updated: 2025-03-19

Post by agentcousto on (no subject) ^{CODESYS Forge talk (Post)}
Hello, I have developed a Python script that I run to import XML files into my project. For this, I use the Python function import_xml(). Everything was working fine when I was using Codesys platform plugins version 2.6.1.2320, but since I upgraded to versions 2.7 and even 2.8, some files are no longer imported correctly. After some research, I identified that all the files containing variables of the type "POINTER TO" are affected. I have attached a screenshot of the error I am encountering. Do you know about this bug? Do you plan to fix it?
Last updated: 2025-03-26

Post by kuegerls on OpC UA server on Raspberry Pi MC SL - Certificate Issue ^{CODESYS Forge talk (Post)}
Hello, I have set up an OPC UA server following several guides, including this one: https://revolutionpi.com/documentation/tutorials/opc-ua-codesys-nodered/. The license for the runtime is installed on the device. However, I am unable to create a certificate for the OPC UA server in the security screen. I always get the error message: "The certificate has not been created by the device." Does anyone have an idea what might be causing this issue? Any help would be greatly appreciated! Thanks in advance! Best regards, Stefan
Last updated: 2025-04-02

Post by wbj0t on Update project from SP20 to SP21 ^{CODESYS Forge talk (Post)}
Hello everyone. I have a problem: I installed new version of codesys IDE. When I try open project in this new version, I have many errors about Visu: rectalnge/button/frame/etc does not exist. How update properly project? 20+ pages of visu pages from 100+ frames and all visu elems looks like "Error image". It is not problem of SP20->SP21. Any update has problems from visu side.
Last updated: 2025-06-09

Post by berkdan on SMC_ReadNCFile2 is always busy ^{CODESYS Forge talk (Post)}
Hello, I’m using CODESYS V3.5 SP18. When I try to use SMC_ReadNCFile2 to read the file /PlcLogic/gcode.nc, the function block's bBusy output remains TRUE indefinitely. Can you help me understand what I might be doing wrong? Here is how I’m calling the function block. The value of strFileName is 'gcode.nc'. fbReadFile( bExecute := bExecute, sFileName := strFileName, bAbort := bCycleStop, fDefaultVel := RetainVariables.xSlowVelocity, fDefaultAccel := RetainVariables.xAcc, fDefaultDecel := RetainVariables.xDec, b3DMode := TRUE, bParenthesesAsComments := TRUE, fDefaultVelFF := RetainVariables.xFastVelocity, fDefaultAccelFF := RetainVariables.xAcc, fDefaultDecelFF := RetainVariables.xDec, ErrorID => gCNC.eErrorId, errorPos => gCNC.eErrorPos, ErrorProgramName => gCNC.eErrorProgName, bBusy => bReadFileBusy, sentences => sentencesss ); Thanks in advance for your help.
Last updated: 2025-06-16

Post by eschwellinger on CODESYS Control for Linux ARM SL (32 bit) on Moxa UC-3100 IPC ^{CODESYS Forge talk (Post)}
I would recommend to ask Moxa for a newer version of Debian. Debian 9 ("Stretch") has reached its end of life and is no longer receiving security updates from the official Debian Security Team as of June 30, 2022. This means any systems still running Debian 9 are vulnerable to security risks and should be upgraded to a newer, supported version of Debian like Debian 10 ("Buster") or Debian 11 ("Bullseye").
Last updated: 2025-07-14

Post by ivan-g on MODBUS ^{CODESYS Forge talk (Post)}
Hi There, I took over a project from a colleague (in GTB) who left the company. When I took over his project, it wouldn't compile because some libraries were missing. I managed to recover quite a few libraries, but I can't find the library that contains the block functions shown in the image. Here are a few examples: Fb_RegMel_ISO Fb_DefModbus FbDecalConsSalSO Fb_Autor_FreeCool_CTA_C I'm a little stuck at the moment, so if you see a Facebook post that speaks to you, don't hesitate to get in touch! Thank you in advance for your help.
Last updated: 2025-08-05

Post by ivan-g on MODBUS ^{CODESYS Forge talk (Post)}
Hi There, I took over a project from a colleague (in GTB) who left the company. When I took over his project, it wouldn't compile because some libraries were missing. I managed to recover quite a few libraries, but I can't find the library that contains the block functions shown in the image. Here are a few examples: Fb_RegMel_ISO Fb_DefModbus FbDecalConsSalSO Fb_Autor_FreeCool_CTA_C I'm a little stuck at the moment, so if you see a FB that speaks to you, don't hesitate to get in touch! Thank you in advance for your help.
Last updated: 2025-08-05

Post by davidbo on All the things needed for anonymous login to OPC UA ^{CODESYS Forge talk (Post)}
When you have a deep object structure where not all values are not exposed to OPC UA, the top object will not have a V check mark but be filled fully out. In that case CODESYS do not always registrate changes to inner object. Solution set a V in the checkbox of the top object, build, download. Now you can browse, but all values in the top object will be selected, then you can deselect the ones you don't want, build, download and it works
Last updated: 2025-09-10

Post by gunstr on CODESYS control on RPi starts, shortly runs, then exits ^{CODESYS Forge talk (Post)}
The problem has been resolved. Two findings are described below for future reference. The new RPi hw delivered during August 2025 has a MAC address from a new vendor series that is not supported by old runtimes. 4.17.0.0 or above is required. 4.17.0.0 does not pick up the correct architecture during installation and aarch64 has to be manually configured either in the GUI under operations or in /etc/codesyscontrol/CODESYSControl_User.cfg under the [CmpRasPi] section.
Last updated: 2025-09-16

Post by arvindkumar on Wago plc not going back to RUN Mode after Power failure ^{CODESYS Forge talk (Post)}
Hi im using wago pfc750-8207 plc and my programming software was codesys v2.3, im facing some issue in my plc after power failure my plc not going back to run mode sometimes, i did sourecode download, boot application created and still facing this issue, out of 10 power failure 8 times its going to run mode some time its missing to go run mode and only sys indication is in on condition Kindly please help me.
Last updated: 2023-12-15

Post by mputaggio on Recipe Manager - RecipeManCommands, load & write wrong values, Bug? ^{CODESYS Forge talk (Post)}
Hello, We encountered the same issues on both recipe library versions 4.2.0.0 and the newest 4.3.0.0. The Arrays of structs get saved correctly but loading them restores only some indexes, while others get lost or completely wrong. We have been using the same recipes for the last two years on recipe manager vers. 3.5.17 withoud issues. There also seems to be a different behaviour in vers. 4.3.0.0 but it's still incorrectly loading the recipes. Did you find any workaround or solution? Codesys version used: 3.5.19.50
Last updated: 2023-12-15

Post by spiessli on Softmotion axis to CANopen Maxon IDX drive ^{CODESYS Forge talk (Post)}
Hi, I want to use Maxon IDX drives for some simple robotic applications. I have used Maxon's Epos for generating a DCF file to import in Codesys (attached). Then I can add the IDX motors under a CANopen manager in the device tree. Unfortunately, I cannot add a "softmotion axis" to the IDX motors. Now I am wondering, why? Without being able to attach a softmotion axis to the device in the device tree, the use of the motor is greatly reduced... spiessli
Last updated: 2024-01-05

Post by andrax on Stop Programm geladen Ausnahmefehler ^{CODESYS Forge talk (Post)}
Hallo, ich habe seid neustem ebenfalls dieses Problem auf den Raspberry. Codesys 3.5.18 Nach dem Download geht die SPS in STOP und es blinkt schwerer Ausnahmefehler. Der Fehler kommt sporadisch und ist nicht reproduzierbar. Es passiert beim kompletten Download, aber auch bei Änderungen. Wie kann ich den Fehler eingrenzen? Nachtrag: Wenn der Fehler kommt, ist die Runtime auf dem Raspberry nicht mehr ansprechbar. Der Raspberry selbst schon. Für einen neuen Download muss ich den Raspberry neu starten. Das selbe ist auch in der Programmierumgebung, die Software hängt sich auf.
Last updated: 2024-01-15

Post by sturmghost on Find visualization elements that require a lot of computing time ^{CODESYS Forge talk (Post)}
I found out that the Codesys simulation mode is not good to measure performance. As soon as I upload the code onto the hardware PLC I can see that my visu-task needs around 60 ms to complete. I'm wondering if there is a possibility to find out which visualization/visualization element takes a lot of computing time? Then I would look for ways to decrease the long computing time.
Last updated: 2024-01-22

Post by mejak on Raspberry Pi USB HID RFID Reader - read ID in plc program ^{CODESYS Forge talk (Post)}
Hello, I have an RFID reader that is detected as a keyboard. While looking for information, I came across examples using visualization. I would like to read the ID without visualization or external code in python, only in PLC. I found on the forum that you can try reading directly from potru /dev/... https://forge.codesys.com/forge/talk/Runtime/thread/24b3527036/ How to read values directly in codesys? Or maybe there is another solution? Best Regards
Last updated: 2024-01-25

Post by thomas-moba on "sudo"-Befehle über die Funktion "SysProcessExecuteCommand2" ^{CODESYS Forge talk (Post)}
Hello, I need to execute "sudo" commands via CoDeSys 3.5 SP 19 P5 using the "SysProcessExecuteCommand2" function. Commands without sudo are no problem, but as soon as sudo is used in a .sh or a single command, it does not work. Command=AllowAll is entered under "SysProcess" in CODESYSControl.cfg. Nevertheless it does not work. Does anyone know what the problem could be? Greetings, Thomas
Last updated: 2024-02-01

Post by thomas-moba on "sudo"-Befehle über die Funktion "SysProcessExecuteCommand2" ^{CODESYS Forge talk (Post)}
Hallo Herr Schwellinger, vielen Dank für die Antwort. Leider hat auch das weglassen des "sudo"-Befehls kein Erfolg. Folgendes passiert: Bild 1: Befehl in der Konsole eingegeben ohne sudo; Uhrzeit wird nicht gestellt (keine Berechtigung). Bild 2: Befehl mit sudo ausgeführt, Uhrzeit wird gestellt. Bild 3: Befehl ohne sudo von CoDeSys aus ausgeführt; Rückgabewert gibt die Uhrzeit an, die eingestellt werden sollte, Uhrzeit wird jedoch NICHT eingestellt. Haben Sie noch eine Idee was es sein könnte?
Last updated: 2024-02-02

Post by elektron785 on CAN-Bus in Demo-Version ^{CODESYS Forge talk (Post)}
Hallo, wie verhält es sich mit der Demo-Version und Datenübertragung z.B. via CAN-Bus. Der Bus läuft, das Device befindet sich im Zustand "Operational" aber es werden keine Daten von der Soft-SPS empfangen. Ich benutze aktuell eine nicht lizenzierte Version von CoDeSys Control for Linux ARM64SL. Normalerweise sollte die Demo-Version uneingeschränkt laufen - also kann ich davon ausgehen, dass es sich um einen Programmierfehler handelt oder ist die Feldbusfunktion ohne Lizenz doch in irgendeiner Form eingeschränkt verfügbar (außer dem 30 Minuten Limit nach Reboot)?
Last updated: 2024-02-06

Post by suthesan on Error when I go online on Simulation or PLC ^{CODESYS Forge talk (Post)}
Hello I not sure if I made this topic under the right category. But I have a error, when I try to run a simple code on simulation or PLC. I have also tried to make a fresh project. I am testing the PLC and want to see if there is some way I can make an actuator run. Please help by looking at the picture, Iam stuckd and I don't know how to fix it.
Last updated: 2024-02-07

Sort by relevance or date