Post by toffeebonbon on EL7041-0052 - does it run with EL7041 SoftMotion? ^{CODESYS Forge talk (Post)}
Good morning everyone. In my setup I am trying to use a couple of EL7041-0052 (the EL7041 variant without terminals for an encoder) to run stepper motors without feedback. When using the softmotion drivers for the EL7041 (Rev22 and Rev24, even selecting external feedback type doesn't work) the device log shows warnings for the corresponding hardware: "SDO write error 0x1 -> 0x8012:0x08 eError 0x1 AbortCode 0x6090011". 0x8012:0x08 is the register for the Feedback Type. My best guess was setting the the register value in the start parameters to zero, but the result is the same. What else can I try to get the hardware to work? I have screenshots attatched showing the running fieldbus and the log messages. EDIT: One clarification: the "device log" that shows the error is the PLC, not the ethercat terminal. The log of the terminal itself shows neither errors nor warnings. BR Robert
Last updated: 2023-11-29

Post by arundara on Variable Sync Issue In Soft Plc Redundancy ^{CODESYS Forge talk (Post)}
Hello, I was trying to create a redundancy POC for our application where we read data from few modbus tcp devices. As there is a limitaion that modbus tcp device support only for single master device, we wanted to test how the variable sync happens in redundancy mode. For that i have used the redundancy sample code added a variable "b" under a condition. What i observed was while active controller is running, if passive controller is powerup, passive controller is able to sync all the data configured for redundacny. But after that the variable data which resided under a condition is not synching from active to passive controller. I have attached the image where i have highlighter the variable. Can some help me to understand how redundacny work in codesys soft plc and if there is a solution to sync variable which are under condition, please explain the same or suggestion to achieve the same. Hardware - Raspberry Pi (2 qty) Redundancy licence used - yes in both controllers. Codesys runtime - 4.9.0.0 Codesys software version - V3.5 SP19 if i have posted this question in wrong section, please do let me know in whcih section i have to post this question.
Last updated: 2023-12-01

Post by nizrahel on OpC UA server on Raspberry Pi 64 SL runtime ^{CODESYS Forge talk (Post)}
Hi all! I'm working on an home project using a Raspberry Pi 3 device with Codesys for Raspberry Pi 64 SL runtime. I would like to create the HMI interface with Siemens WinCC Unified (or Advanced) configuring the Raspberry as OPC UA server. I tryed everything, but I didn't find the way to let the OPC UA connection works using UaExpert. I tryed to use anonymous connection, authenticated connection and the ip address instead of the server name in the path connection. There is no way to connect to the OPC UA server and I was asking myself if this feature is really supported for the runtime version used. Another strange thing I noted, is that is not possible to quickly create an OPC UA certificate in the Security Screen, as show in any tutorials. I have correctly created the Symbol Configuration enabling the OPC UA feature. I attach to this topic some printscreen of the actual configuration (sorry for the italian language interface, but I didn't find the way to switch to english). Thank you very much in advance for your support and advices!
Last updated: 2023-12-03

Post by nathant on Saving variable values on power cycle (RevPi Connect) ^{CODESYS Forge talk (Post)}
Hello, this seems to be a known issue, but persistent/retain variables don't seem to work properly on RevPi devices. Is there a workaround to this? All I need is for a few configuration variables to be remembered through power cycle.
Last updated: 2023-12-03

Post by voffi on CODESYS Custom Build Step ^{CODESYS Forge talk (Post)}
Good morning! Is there a way to run a python script or something else automatically after CODESYS (3.5) did its build or before download? I am searching for something like the Custom Build steps in Visual Studio. Thank you! Voffi
Last updated: 2023-12-07

Post by voffi on documentation in function block ^{CODESYS Forge talk (Post)}
Using < br > did it for me in CODESYS 3.5.19 // 2023-12-05 Line 1<br> // 2023-12-06 Line 2<br> shows up in Library Manager with line breaks.
Last updated: 2023-12-07

Post by hwopereis on How to use Application Trigger in Modbus TCP Server ^{CODESYS Forge talk (Post)}
I'm now circumventing the problem by creating a separate TCP client for all Write actions. Upon registering a changed variable, I enable this client, until the change is processed.
Last updated: 2024-07-01

Post by mos89p on is it possible to connect to a newer runtime from HMI runtime 3.5.16 ^{CODESYS Forge talk (Post)}
is it possible to connect to a newer runtime from HMI runtime 3.5.16 via Datasource manager for example a 3.5.20 ?
Last updated: 2024-07-02

Post by tariq on Using Hilscher CIFX Cards as EtherCAT Masters in CODESYS ^{CODESYS Forge talk (Post)}
Dear Codesys Support Team, I hope this message finds you well. I am currently working on a project that involves using a Hilscher CIFX card to act as an EtherCAT master within the CODESYS environment. Despite following the available documentation and setup guides, I have encountered some challenges and require assistance to ensure proper configuration and operation. Questions: 1- Could you please confirm if the Hilscher CIFX card is supported as an EtherCAT master in CODESYS? If so, are there specific drivers or configuration files that need to be installed? 2- Are there detailed setup guides or example projects available that demonstrate the integration of Hilscher CIFX cards with CODESYS for EtherCAT communication? 3- Is there any additional software or plugins required for ensuring seamless communication between the CIFX card and the EtherCAT slaves within CODESYS? Your support and guidance on these matters would be greatly appreciated, as it is crucial for the success of our project. Thank you for your time and assistance. I look forward to your prompt response. Best regards, TB
Last updated: 2024-07-02

Post by kunz on Responsive Design Example ^{CODESYS Forge talk (Post)}
Can nobody help? Here the BP when the Smartphone is selected, but for the visu of the smartphone still the monitor visu is show. Tested it with a Control WIN x64
Last updated: 2024-07-03

Post by viktorr on ShareMemory library documentation ^{CODESYS Forge talk (Post)}
Hello, I was wondering if there was further documentation on the SharedMemory library in CodeSys outside of the code example provided, or maybe a way to access the source code of the shared memory implementation. Thank you in advance for any advice. - Viktor
Last updated: 2024-07-03

Post by viktorr on Shared Memory Requested Size ^{CODESYS Forge talk (Post)}
Hello Derek, I recognize this is an older post, but i was wondering if found any ways to remedy this. I am running into what i think is the same problem you had here. Thank you in advance for any information, Viktor
Last updated: 2024-07-04

Post by psychoengineer on Trouble Writing Files to External Paths in CODESYS ^{CODESYS Forge talk (Post)}
Hi! Do you know how to properly configure SysFile for COdesys Control Win64? Where is it that file on the PC disk and whatr to add?
Last updated: 2024-07-05

Post by thommy54 on Raspi-Cam: CameraStream.project nicht zum Laufen zu bringen ^{CODESYS Forge talk (Post)}
Hallo, thank you for thge link. Never before I read about a RPi_Cam_Web_Interface_Installer.sh. I will try it... Thank you Thomas
Last updated: 2024-07-05

Post by psychoengineer on Trouble Writing Files to External Paths in CODESYS ^{CODESYS Forge talk (Post)}
Hi! Do you know how to properly configure SysFile for COdesys Control Win64? Where is it that file on the PC disk and what to add?
Last updated: 2024-07-05

Post by psychoengineer on Trouble Writing Files to External Paths in CODESYS ^{CODESYS Forge talk (Post)}
Hi! Do you know how to properly configure SysFile for COdesys Control Win64? Where is it that file on the PC disk and what to add?
Last updated: 2024-07-05

Post by disha on Export data with the Trend API ^{CODESYS Forge talk (Post)}
Can you please share the code as i am the beginner for codesys. I don't have any idea that how sqlite is integrated with the codesys.
Last updated: 2024-07-08

Post by mucleus on What is the solution for "Application stopped on recovery switch request"? ^{CODESYS Forge talk (Post)}
Component ID 10 is my own log message by LogAdd Function. I want to know in what cases the application stops.
Last updated: 2024-07-09

Post by xgongx on What is the insights of IoDrvEtherCAT.DCInSyncWindow? ^{CODESYS Forge talk (Post)}
It is well known that you need to increase the value of IoDrvEtherCAT.DCInSyncWindow to solve the "Fieldbus lost synchronicity" issue. In the official document, IoDrvEtherCAT.DCInSyncWindow is explained as the toleration of a certain jitter. But the official document doesn't explain what kind of the jitter is. Is it the jitter of DC sync deviation, master timer or something else? It is very important to know the insights of IoDrvEtherCAT.DCInSyncWindow. For example, if it is the toleration of DC sync deviation, and the official recommending value is 200us for CODESYS SoftMotion. It means maximum of DC sync deviation is 200us. It is unacceptable for some high precision motion control tasks, for example high speed gear task, etc. Increasing the value of IoDrvEtherCAT.DCInSyncWindow will increase the deviation of motor rotation sync if it is the toleration of DC sync deviation. So, would anyone tell me what the insights of IoDrvEtherCAT.DCInSyncWindow is? Thanks.
Last updated: 2024-07-09

Post by installwhat on What is the solution for "Application stopped on recovery switch request"? ^{CODESYS Forge talk (Post)}
Well still similar questions remain. I don't know of "CmpRecoverySwitch" and the only thing google has to offer is your xml file. I think you'd need to provide a lot more info before anyone makes much effort here.
Last updated: 2024-07-09

Post by akos on Soft motion kinematic zones ^{CODESYS Forge talk (Post)}
Hello Everyone, Is there any solution to define safety/forbidden zones in the coordinate system of the kinematics? Its not enough, to define only limits in my servo axes! I need zones in 3D! :) Thanks for the help!
Last updated: 2024-07-10

Post by pazderai on CanOpen write issue ^{CODESYS Forge talk (Post)}
Hi,is there any canopen library where is implemented sdo write with unspecified datalength (command byte 0x22)? I tried caa cia405 canopen library but it doesnt support this, but my slave device accept only 0x22. Thank you for any help.
Last updated: 2024-07-16

Post by pazderai on CanOpen write issue ^{CODESYS Forge talk (Post)}
Hi,is there any canopen library where is implemented sdo write with unspecified datalength (command byte 0x22)? I tried caa cia405 canopen library but it doesnt support this, but my slave device accept only 0x22. Thank you for any help.
Last updated: 2024-07-16

Post by brzozka100 on Change modbus server parameters from program ^{CODESYS Forge talk (Post)}
Hello, is there a possibility to change modbus server parameters (baud rate, parity, etc.) configured in devices tree from PRG? I need to be able to change them, for example, from HMI.
Last updated: 2024-07-16

Post by brzozka100 on Change modbus server parameters from program ^{CODESYS Forge talk (Post)}
Hello, is there a possibility to change modbus server parameters (baud rate, parity, etc.) configured in devices tree from PRG? I need to be able to change them, for example, from HMI.
Last updated: 2024-07-16

Sort by relevance or date