Post by preimesbergert on Raspberry Pi 4 B HW 1.5 Codesys control 4.10.0 stopps after a few seconds ^{CODESYS Forge talk (Post)}
Wanted to play a bit with a raspberry Pi 4 Model B HW 1.5 and Codesys. Regardless of the image (tried 32bit / 64bit version from Raspberry Pi Imager) and with all tested Codesys Control versions (4.2.0, 4.8.0, 4.10.0) and regardless if single core / multicore / 64 bit variant, always is the runtime stopped after about 30sec with the nice message: ooops... this runtime was built for RASPBERRYPI. Hardware version or firmware version not supported! (-7, 0x00000BB8, 0xFFFFFFFB) Whats wrong with it?!?!? I read a lot about the issue in topics from 2020-2021 but it always was stated with new Codesys control version issue will be fixed (4.4 for example) but still it is there.
Last updated: 2023-12-21

Post by mp9876 on Device logon problem following fresh install ^{CODESYS Forge talk (Post)}
Yes it had been the case I believe as I have seen that message regarding they were not the same. I had update the device though to match them and that still did not fix the problem. I gotta say I wanted to get out of that situation and attempted a lot of things and then I did two things at the same time that fixed my problem: Wiped the 64 bit version and installed the 32 bit version Installed latest SP20 I wish I knew which one of these actions fixed the problem but now I gotta catch up on this IDE learning; it's been quite a learning experience I have to say! Thank you very much for your time and advice; much appreciated!
Last updated: 2024-03-19

Post by m83coding on Raspberry Pi Codesys SPI Master ^{CODESYS Forge talk (Post)}
Hello, I am trying to control shift registers 74HC596 and 74HC165 via Raspberry PI with SPI interface. So far I did it with a Microcontroller and now I wanna upgrade my Projekt with Raspberry Pi and Codesys Software to be more flexible. I tried to adapt PiFace Function Block to just send or recive a 8 bit via SPI interface of the my Raspberry Pi. With following code (see attached screenshots) * PLC_PRG * PiFaceDigital * PiFaceDigital.write8 * PiFaceDigital.read8 I have a signal at SCK and MOSI pin of the PI, so far so good. But I really struggle with the unterstanding of the code. Is there some detailed description of each line of code? Or is there somebody in the community who can explain each line of code? Or is there a more simple way to send / recive 8 bit via SPI? Manuel
Last updated: 2024-04-23

Post by salvadegianluca on SysPlcCtrl23 and C0338: The library 'cmperrors interfaces, 3.5.5.0 (system)' is supported just in 32 bit applications ^{CODESYS Forge talk (Post)}
Good afternoon to everyone; I'm stuck with this error and I don't know how to get out from it... I tried several time googling for alternative systems to control the PLC applications and resets but without success. I would like to realize the possibility to reset the CPU and to start/stop the applications as it was possible with the SysPlcCtrl23, but this library is no longer supported in 64 bit systems and it seems due to the cmperrors interfaces sub library that was included in the above said one. Someone found a work around for this issue?
Last updated: 2024-06-14

Post by salvadegianluca on SysPlcCtrl23 and C0338: The library 'cmperrors interfaces, 3.5.5.0 (system)' is supported just in 32 bit applications ^{CODESYS Forge talk (Post)}
Good afternoon to everyone; I'm stuck with this error and I don't know how to get out from it... I tried several time googling for alternative systems to control the PLC applications and resets but without success. I would like to realize the possibility to reset the CPU and to start/stop the applications as it was possible with the SysPlcCtrl23, but this library is no longer supported in 64 bit systems and it seems due to the cmperrors interfaces sub library that was included in the above said one. Someone found a work around for this issue?
Last updated: 2024-06-14

Post by salvadegianluca on SysPlcCtrl23 and C0338: The library 'cmperrors interfaces, 3.5.5.0 (system)' is supported just in 32 bit applications ^{CODESYS Forge talk (Post)}
Good afternoon to everyone; I'm stuck with this error and I don't know how to get out from it... I tried several time googling for alternative systems to control the PLC applications and resets but without success. I would like to realize the possibility to reset the CPU and to start/stop the applications as it was possible with the SysPlcCtrl23, but this library is no longer supported in 64 bit systems and it seems due to the cmperrors interfaces sub library that was included in the above said one. Someone found a work around for this issue?
Last updated: 2024-06-14

Post by salvadegianluca on SysPlcCtrl23 and C0338: The library 'cmperrors interfaces, 3.5.5.0 (system)' is supported just in 32 bit applications ^{CODESYS Forge talk (Post)}
Good afternoon to everyone; I'm stuck with this error and I don't know how to get out from it... I tried several time googling for alternative systems to control the PLC applications and resets but without success. I would like to realize the possibility to reset the CPU and to start/stop the applications as it was possible with the SysPlcCtrl23, but this library is no longer supported in 64 bit systems and it seems due to the cmperrors interfaces sub library that was included in the above said one. Someone found a work around for this issue?
Last updated: 2024-06-14

Post by salvadegianluca on SysPlcCtrl23 and C0338: The library 'cmperrors interfaces, 3.5.5.0 (system)' is supported just in 32 bit applications ^{CODESYS Forge talk (Post)}
Good afternoon to everyone; I'm stuck with this error and I don't know how to get out from it... I tried several time googling for alternative systems to control the PLC applications and resets but without success. I would like to realize the possibility to reset the CPU and to start/stop the applications as it was possible with the SysPlcCtrl23, but this library is no longer supported in 64 bit systems and it seems due to the cmperrors interfaces sub library that was included in the above said one. Someone found a work around for this issue?
Last updated: 2024-06-14

Post by salvadegianluca on SysPlcCtrl23 and C0338: The library 'cmperrors interfaces, 3.5.5.0 (system)' is supported just in 32 bit applications ^{CODESYS Forge talk (Post)}
Good afternoon to everyone; I'm stuck with this error and I don't know how to get out from it... I tried several time googling for alternative systems to control the PLC applications and resets but without success. I would like to realize the possibility to reset the CPU and to start/stop the applications as it was possible with the SysPlcCtrl23, but this library is no longer supported in 64 bit systems and it seems due to the cmperrors interfaces sub library that was included in the above said one. Someone found a work around for this issue?
Last updated: 2024-06-14

Post by martinlithlith on Device User Logon and No device is responding.. Pi4b codesys 3.5 SP19 2 + (64-bit) ^{CODESYS Forge talk (Post)}
Hi, Thank you for your reply! What should be the version 4.9.0.0? I have a user named pi on the pi, thats what i´m using as credientials to be able to for example update/install runtime. Or do i need another user? once agin, thank for the reply! Martin
Last updated: 2023-09-11

Post by timvh on Send file from codesys to...... ftp, cloud, etc ^{CODESYS Forge talk (Post)}
You can use the (open source) FTP client in Forge. This works on 64 bit systems. See: https://forge.codesys.com/prj/ftp-client/code/HEAD/tree/ As this is open, the idea is that when you use it and make improvements to the source code, that you also commit this in a branch so others can also benefit from it.
Last updated: 2023-11-07

Post by ewi04 on Git - User identification data is lost when codesys is closed ^{CODESYS Forge talk (Post)}
Hallo, it's not a big problem, but it is a bit annoying. The git user identification data is lost when codesys is closed. So I have to enter the information again and again. Is there a way to save the data? Environment: Codesys V3.5 SP19 Patch 4 (64Bit), Git 1.3.0.0 Thanks
Last updated: 2023-11-22

Post by shabroz-gill on Unable to load boot application on ARMv7 device restart ^{CODESYS Forge talk (Post)}
I download an application to an ARMv7 32 bit device. I start the applicatin and it all works fine. But when i restart the device the boot app is not able to start. I have to redownload the application from the development environment to get to run again. I get the following error messages in the log on the restart
Last updated: 2023-11-30

Post by chirag on About byte swap and convert into 16 bits ^{CODESYS Forge talk (Post)}
Hello, I have %QB0 8 high bits and %QB1 8 low bits . How can i swap bits %QB0 and %QB1 for requirment positions in a 16-bit value ? after that i need %QB0 and %QB1 in to 16bits . For that, i need help. Please see attached pictures for your reference. Thanks in advance.
Last updated: 2023-12-04

Post by bossjosh21 on RevPi Connect RS485 ^{CODESYS Forge talk (Post)}
Hi Sir Kevin. May I know how you came up with this solution. Im a bit confused but I tried to put this. [SysCom] Linux.Devicefile=/dev/ttyRS48 (remember, no 5 at the end!) then set com port in codesys to 6. It also works for me but want to know where did you get this. Thank you.
Last updated: 2023-12-06

Post by preimesbergert on Codesys Control for Raspberry Pi 4.10.0.0 - Raspberry Pi OS > 2023-12-05 ^{CODESYS Forge talk (Post)}
Same issue here: Raspberry Pi 4 Model B HW 1.5 Regardless of the image (tried 32bit / 64bit version from Raspberry Pi Imager- all the "standard version") and with all tested Codesys Control versions (4.2.0, 4.8.0, 4.10.0) and regardless if single core / multicore / 64 bit variant.
Last updated: 2023-12-21

Post by dhumphries on Control Runtime Toolkit ^{CODESYS Forge talk (Post)}
I have a video demonstrating the procedure to install the runtime on a linux device. https://youtu.be/rj0dOhgnGjs?si=OJoA-kgc1saxIweR This demonstration shows how to install the runtime on a X86 based controller, it should be the same for an ARM based device, but you'll need to install the add-in for Codesys control for Linux ARM SL (or the 64 bit add-in.)
Last updated: 2023-12-30

Post by peter-skokanek on Rpi install runtime licence on SP13 ^{CODESYS Forge talk (Post)}
Hi, I have an older project which has been running for years. Unfortunately I have to replace current Raspberry. I repplaced it by new rpi 3 with newest 32 bit Raspberry OS. I oredered a new runtime licence. When I try to activate it, the connection to target is interrupted immediatelly after press next button in the last step of instalation.
Last updated: 2024-01-08

Post by yannickasselin on Linux ARM64 SL, GPIO Access ^{CODESYS Forge talk (Post)}
A bit of work but maybe possible to make your own driver using "CODESYS Control SL Extension Package". Look at the "ExternalIoDrv" example. It is installed in "C:\Program Files\CODESYS 3.5.20.0\CODESYS\CODESYS Control SL Extension Package" when you install the "CODESYS Control for Linux SL".
Last updated: 2024-05-08

Post by nltheves on Raspberry PI4 Serial Port ^{CODESYS Forge talk (Post)}
Hi Ricardo. I was having the same problem with Codesys and a Raspberry Pi 2W while using the GPIO uart. Your post helped me a lot. Thanks! But could not understand why MODBUS parity bit makes Codesys MODBUS COM driver stopping to work after first request transmission. Did you see this @eschwellinger ? Regards, Nelson
Last updated: 2024-07-18

Post by fless on SMC_NCDecoder very slow to decode lines ^{CODESYS Forge talk (Post)}
Hi, I got good results with SMC_NCDecoder, SMC_CheckVelocities, etc. in a freewheeling task with lower priority (higher number). Still takes some time but I'm using many variables and loops in my g-code and more preprocessing like SMC_SmoothPath, SMC_LimitDynamics, SMC_CheckForLimits. PS: your buffer size seems a bit high for 34 lines of g-code
Last updated: 2024-08-23

Post by tehthoams on Time will not read 12 ^{CODESYS Forge talk (Post)}
I know this post is a bit old, but i'm having this same issue: At noon, %t[hh:mm:ss tt] is displaying 00:00:00 PM There is no text variable, just using the default functionality of the visualization for the time display. This is running on an IFM CR1102 display. has anyone solved this?
Last updated: 2024-10-10

Post by gabor-n on PNIO Connect Parameter Error ^{CODESYS Forge talk (Post)}
It's a bit confusing, the two RPI is the same (board, OS, runtime, programing with Codesys V3.5 SP20 P2) but the one has a codesyscontrol.cfg file and the other has a codesyscontrol_user.cfg file. Shouldn't be the same? And because I over Codesys 3.5 SP 12 this would be the '_user.cfg' for both. Attached...
Last updated: 2024-10-11

Post by tecnocons on Trouble Writing Files to External Paths in CODESYS ^{CODESYS Forge talk (Post)}
Hello everyone, I'm encountering an issue in CODESYS regarding writing files to external paths. Despite correctly configuring the placeholder in the CODESYSControl_User.cfg file to allow access to an external folder, CODESYS doesn't seem to write any files, and no errors are reported. The issue on the older versions was absent with no placeholders. I've checked the operating system permissions, and they seem to be in order, but the issue remains. Has anyone faced a similar situation or has any suggestions on how I might resolve this problem? Any help would be greatly appreciated. Thank you in advance for your support. I'm using raspberry PI as a logger. RPI3 Buster Codesys 32bit SL V4.11 Codesys Win64 3.5.20 [SysFile] PlaceholderFilePath.1=/home/pi/scan, $SCAN$
Last updated: 2024-04-09

Post by orbis-tertius on 3.5 P20 hangs - no response ^{CODESYS Forge talk (Post)}
Is there anybody can help me with the same problem? I have to migrate created project in ver.3.5.17.0 32BIT with runtime 4.7.0 to ver.3.5.20.0 64BIT with runtime 4.7.11.0 due to the new license. All the libraries and dependencies are updaded and there are no any errors. The first compilation and loading to the controller is being compleated well. After this being done and if I am forced to change any values or change any code in the current project, another compilation will be freezed. This problem can be solved if pressed Build/cleen or cleen all. There is another method to solve this; if project is loaded with excluded object (Alarm Configuration), repeated compilations will be done well.
Last updated: 2024-06-27

Sort by relevance or date