Post by jzhvymetal77 on IecVarAccessLibrary.IBaseTreeNode methon ^{CODESYS Forge talk (Post)}
I got this code working again. 3S/CoDeSys, your level of obfuscation and lack of documentation turns a simple task into a monumental complex challenge. The issue was that at some point the IecVarAccessLibrary changed and no longer allowed using IBaseTreeNode to retrieve a child or the number of children. The attached code has been updated to use IIecVarAccess6.VarAccBrowseGetChildByIndex instead. The code was also cleaned up but is still a work in progress. The current example only works one layer deep. This means native data types, arrays, and single-layer structures are supported. However, structure arrays and nested structures are not yet supported.
Last updated: 2025-08-25

Post by kporter on High-resolution drive with SoftMotion ^{CODESYS Forge talk (Post)}
I'm beta-testing a new EtherCAT drive for a rotary (modulo) axis in a system where the encoder resolution is 81920000 counts per rotation. If I enter this in the SoftMotion Scaling/Mapping tab for "increments <=> motor turns", I get the error below on the Commissioning tab. Is SM unable to handle a high-resolution encoder? The bus cycle is currently set to the default of 4 msec (Control Win V3 x64), although I plan to reduce that to reduce latency, possibly by switching to the realtime (RT) master. Is SoftMotion incompatible with high-resolution encoders? SMC_CGR_INVALID_POSPERIOD Invalid modulo period (<= 0 or greater than half the bus bandwidth)
Last updated: 2025-08-25

Post by pernockham on AC Persistence - values are not read from file during start? ^{CODESYS Forge talk (Post)}
I swear I tested this like 20 times yesterday without success. Repeated it today and it works. Maybe the system needed a "real" power reboot? To note. To make a manual edit of a variable I tried some different approaches this is what worked for me. "system/online edited" gvl_var.example_variable REAL:F16#2FFB334H-4 767.7 "manually edited" (with runtime stopped followed by a "cold start" to read from file) gvl_var.example_variable REAL:790.1 (the system will use the manual value but will not set an equivalent "hex" value until next online edit/write cycle)
Last updated: 2025-09-03

Post by alexgooi on Codesys virtual control redundancy ^{CODESYS Forge talk (Post)}
Dear Forum, I’m currently investigating the possibilities of Codesys virtual control (Linux). The research rig consists of a PC (Debian with real time kernel) with a docker server installed on it. The PC is communicating with a Remote I/O and I have to say the performance is great. The process in the container is running (soft) real time. Currently I’m checking if it is possible to replace physical controllers by remote I/O’s and run the Codesys applications on a docker server. If I’m going into this route the reliability of the server is very important (server down, complete installation down), is it possible to make the server redundant without needing 2 separate containers (including licenses), and maintaining the real time behavior? I’m not only expecting direct answers, if you have any idea or thought they are very welcome. Kind regards Alex
Last updated: 2025-09-03

Post by eschwellinger on CODESYS control on RPi starts, shortly runs, then exits ^{CODESYS Forge talk (Post)}
let me check - had a similar case today
Last updated: 2025-09-03

Post by pernockham on Gateway in China - "Gateway not connected" ^{CODESYS Forge talk (Post)}
Trying to communicate (from Europe) with/to a unit located in china, the communication seems blocked/stopped. The edge gateway is installed in a linux environment and was possible to link to my Automation server account using the "Automation service tool". However it seems the unit cannot communicate with the Automation server (a Network scan will give the message "Gateway not connected"). (I have tested the eq. setup with units locally which works.) Anyone having experience situation similar to this and if its possible to make this work? Will a VPN be needed possibly? Other tips?
Last updated: 2025-09-04

Post by beavel on Opening and saving files with fileOpenSave dialog ^{CODESYS Forge talk (Post)}
Tim, you my friend is the best ! Thank you. I wish you a fruitful day.
Last updated: 2025-09-09

Post by ranadheer on PHOENIX CONTACT Axioline PLCnext project in CodeSys SodftPLC ^{CODESYS Forge talk (Post)}
Is my approach to create a project without using PLCnext possible?
Last updated: 2025-09-09

Post by beavel on Opening and saving files with fileOpenSave dialog ^{CODESYS Forge talk (Post)}
Uploading a step by step walk-through in case someone else might find it helpful. :)
Last updated: 2025-09-11

Post by ouzago on ERROR C0138: No matching 'FB_Init' method found for instantiation of VisuClientObjectMgr ^{CODESYS Forge talk (Post)}
When I created a new project in CODESYS using the "Standard Project" template and then added a Visualization, I was receiving the C0138 error during compilation. This issue persisted even with a new, completely empty project. A Quick and Effective Solution (My Method): After many attempts, I solved the problem as follows: From the File -> New Project menu, I selected the "HMI Project" template directly, instead of the "Standard Project" template. After creating the project with this template, I added my POUs, Tasks, and programs (e.g., Ladder, ST). Using this method, the project compiled successfully without any errors. So, my question is: are there any other solutions besides this method?
Last updated: 2025-10-07

Post by trycyclepower on How to transfer data from DINT to Union(16 Bools) which I need to use in Few FBs ^{CODESYS Forge talk (Post)}
Thanks a lot, it worked.
Last updated: 2023-12-14

Post by simotion on Property ^{CODESYS Forge talk (Post)}
Why can't a property be of type REFERENCE TO? Plc goes to stop if I try that.
Last updated: 2023-12-14

Post by simover on TCP/IP client ^{CODESYS Forge talk (Post)}
HELLO thank for you answer!! I'm a beginner can you give me an example?
Last updated: 2023-12-19

Post by fhrask on CoDeSyS OPC DA stops working ^{CODESYS Forge talk (Post)}
Did you find the solution for this issue? i'm having the exact same issue with a new machine at the moment....
Last updated: 2023-12-21

Post by preimesbergert on Raspberry Pi 4 B HW 1.5 Codesys control 4.10.0 stopps after a few seconds ^{CODESYS Forge talk (Post)}
Wanted to play a bit with a raspberry Pi 4 Model B HW 1.5 and Codesys. Regardless of the image (tried 32bit / 64bit version from Raspberry Pi Imager) and with all tested Codesys Control versions (4.2.0, 4.8.0, 4.10.0) and regardless if single core / multicore / 64 bit variant, always is the runtime stopped after about 30sec with the nice message: ooops... this runtime was built for RASPBERRYPI. Hardware version or firmware version not supported! (-7, 0x00000BB8, 0xFFFFFFFB) Whats wrong with it?!?!? I read a lot about the issue in topics from 2020-2021 but it always was stated with new Codesys control version issue will be fixed (4.4 for example) but still it is there.
Last updated: 2023-12-21

Post by preimesbergert on Raspberry Pi 4 B HW 1.5 Codesys control 4.10.0 stopps after a few seconds ^{CODESYS Forge talk (Post)}
Wanted to play a bit with a raspberry Pi 4 Model B HW 1.5 and Codesys. Regardless of the image (tried 32bit / 64bit version from Raspberry Pi Imager) and with all tested Codesys Control versions (4.2.0, 4.8.0, 4.10.0) and regardless if single core / multicore / 64 bit variant, always is the runtime stopped after about 30sec with the nice message: ooops... this runtime was built for RASPBERRYPI. Hardware version or firmware version not supported! (-7, 0x00000BB8, 0xFFFFFFFB) Whats wrong with it?!?!? I read a lot about the issue in topics from 2020-2021 but it always was stated with new Codesys control version issue will be fixed (4.4 for example) but still it is there.
Last updated: 2023-12-21

Post by eschwellinger on Latest Raspberry Pi Update Breaking CODESYS 3.5.16.0 ^{CODESYS Forge talk (Post)}
We are working on a fix for 4.11.0.0 version.
Last updated: 2023-12-22

Post by fajean on Issues with "Add all instance path" ^{CODESYS Forge talk (Post)}
In the past, we have routinely used the "add all instance paths" function to automatically add variables to VAR_CONFIG lists. My recollection is that compiling a project did not require VAR_CONFIG to be fully populated, and, once successfully compiled, instance paths could be added. Errors related to missing declarations, if I recall correctly, were thrown when downloading to the PLC, they did not prevent a successful compile. At some point, it stopped working. Missing declarations in a VAR_CONFIG now cause a compile error, so the application is never "current", the only reason I can see being the missing VAR_CONFIG declarations themselves (no other error). We observe the same behavior across all our projects. This is really aggravating, and I must be missing something simple. We use 3.5 SP17p3, 64 bits. Can anyone help?
Last updated: 2023-12-29

Post by svn123 on Can V3.5.19 and V2.3.9 be installed on same Windows10 PC without affecting each other? ^{CODESYS Forge talk (Post)}
Thanks! Wishing you a great year ahead! svn123
Last updated: 2023-12-29

Post by eschwellinger on Save Recipe on Paspberry ^{CODESYS Forge talk (Post)}
permissions, since a security related change it is not allowed to save files outside of the Plclogic directory. Use /var/opt/codesys/Plclogic/
Last updated: 2023-12-29

Post by domoticom on multiply gives negatives ^{CODESYS Forge talk (Post)}
thnx, meanwhile I added a INT_TO_REAL, now it works. Can I leave it like this or better DINT ?
Last updated: 2024-01-04

Post by reinier-geers on Raspberry add to codesys ^{CODESYS Forge talk (Post)}
I bought a respberry license. Now i want to add it to my software. The manager starts. But there is an error.
Last updated: 2024-01-08

Post by jeroen on Ramp function ^{CODESYS Forge talk (Post)}
Hi, will check the CodeSys function blocks. Didn't know those and usually the OSCAT lib is a bit more advanced. Kind regards!!
Last updated: 2024-01-10

Post by toby on Ethercat Servo Setup ^{CODESYS Forge talk (Post)}
Hi everyone, so a little update to this, I've come back to this project in the new year, and got it working. Yeah!, However, now with the new licensing setup, I need a new SoftMotion license, but it doesn't seem to be compatible with the previous Raspberry Pi SL license. Has anyone had any luck with Raspberry Pi and SoftMotion_Lite? Specifically the licensing of such? My customers new installation needs to be rebooted every 30min which is causing headaches! Another option is to not use the SoftMotion function blocks, and control the EtherCat amplifier directly, but I'm not sure how to do so. Does anyone have a specific example project of how to control a servo without the use of the SoftMotion function blocks? Thanks everyone for any assistance rendered. It's very much appreciated! Toby
Last updated: 2024-01-10

Post by eschwellinger on SM Drive license error ^{CODESYS Forge talk (Post)}
goto the licensing metrix tab in CODESYS an check which license ...or send us a screenshot of it here
Last updated: 2024-01-10

Sort by relevance or date