Post by gunstr on CODESYS control on RPi starts, shortly runs, then exits ^{CODESYS Forge talk (Post)}
I now tried to install 4.17.0.0 on a fully clean installations: A brand new RPi 4B Install latest Raspberry Pi OS Lite, Release date 13 May 2025, 64bit run sudo apt update && sudo apt full-upgrade When asked - Select to install the updated version of '/etc/initramfs-tools/initramfs.conf' Install CODESYS Control for Raspberry Pi SL. version 4.17.0.0 Log output: [INFORMATION] Connected successfully! [INFORMATION] Successfully connected to target (192.168.0.197) [WARNING] No supported container engine found on device. You have to install a supported container engine to use Virtual Control. Please contact the Administrator of the device. [WARNING] Error detecting container architecture [INFORMATION] Finished reading device information [ERROR] Error output: /var/lib/dpkg/info/codesyscontrol.postinst: 88: check_legacy_extensionapi_folder: not found [INFORMATION] Standard output: Selecting previously unselected package codesyscontrol. [INFORMATION] Standard output: (Reading database ... 76772 files and directories currently installed.) [INFORMATION] Standard output: Preparing to unpack .../codesyscontrol_raspberry_4.17.0.0_all.deb ... [INFORMATION] Standard output: Unpacking codesyscontrol (4.17.0.0) ... [INFORMATION] Standard output: Setting up codesyscontrol (4.17.0.0) ... [INFORMATION] Standard output: make config rw [INFORMATION] Standard output: set folder permissions [INFORMATION] Standard output: prepare permissions [INFORMATION] Standard output: check legacy extension api folder [INFORMATION] Standard output: create and install daemon [INFORMATION] Standard output: codesyscontrol started [WARNING] Unable to detect Raspberry Pi Architecture. Setting armv6l as default, you can change this through the settings panel. [INFORMATION] Standard output: codesyscontrol stopped [ERROR] Expected exit value of command failed: expected 0, received 1 [WARNING] Error setting the Raspberry Pi Architecture [ERROR] Error installing codesyscontrol If I read the log correctly the control is actually installed but cannot start. I'm running out of ideas how to proceeed now, any suggestions are welcome.
Last updated: 2025-09-03

Post by mikek10 on Ethernet/IP 4.6.0 causing exceptions? ^{CODESYS Forge talk (Post)}
Hi, I have a project currently in development, it has a number of Ethernet/IP devices (18 adapter devices with Codesys as scanner, another scanner device with codesys as adapter). This has been stable whilst on factory floor for several months (though prior to that I did have some Ethernet/IP issues which were resolved by adjusting RPI rates). Today I tried updating to Ethernet /IP 4.6.0 from 4.5.1, subsequent to this I had 2 exceptions in a 2 hour period, I reverted to 4.5.1 and have had no further exceptions. Note I do have a device (Zebra printer) that frequently times out and reconnects, this does not seem to cause any issues in operation and does not cause any exceptions with 4.5.1. I believe the root cause of this is on the Zebra side, however there does not seem to be any adjustment I can make to prevent the time outs. Information from device log is in screenshot attached.
Last updated: 2024-06-27

Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Post by yannickasselin on codesys VLAN tagging ^{CODESYS Forge talk (Post)}
Hi, I am looking for exactly the same thing. I would think that using a layer 2/3 managed switch should work but I am not convinced. I would like to test it in order to see if it would be possible to run many Codesys Docker instances on a server and run only 1 ethernet cable from the server to a managed switch closer to the machines beeing controlled instead of having to run multiple long ethernet cables. I was going to buy a managed switch in order to test it but I want to first make sure it is possible and I want to figure out exactly what kind of switch I would need. Is this even possible? I think this is a feature that would be very useful paired with "Codesys Virtual Control SL". Thank you
Last updated: 2024-09-07

Post by dkugler on Webvisu Combined Authentication ^{CODESYS Forge talk (Post)}
you are able to do this all in one screen. It is possible to set the rights of every element to visible but not editable for the user "none". so everyone is able to see this elements, but can't do any changes. At the login button you set the rights to editable for the user "none" to be able to go to the login. Every element that should be hidden before logging in, set the rights visible and editable only for "higher" users. Hint: to change rights you are able to select more then one element and edit rights for all at the same time. Saves a lot of time! Good luck!
Last updated: 2025-09-03

Post by niallel on Continuous MC_PositionProfile ^{CODESYS Forge talk (Post)}
Hi, Is it possible to have a MC_PositionProfile that runs continuously again and again without stopping the motor and starting again. I have a profile that contains about 50 steps that I want to repeat. At the end of each run the motor comes to a stop before the next one starts. My code checks for Done, then resets the Execute to False before setting Execute to True to run again, and I think this is causing the motor to go to standstill before starting again. There doesn't seem to be a BufferMode option like with MC_MoveAbsolute. Is it possible to do this? Many thanks,
Last updated: 2024-04-11

Post by ac-spr on Runtime variable that indicates a user is online to the code ^{CODESYS Forge talk (Post)}
Looking to access a variable at runtime that indicates a user is online to the code. essentially want to use this value to feedback to the user on the HMI. we use turck and bosch rexroth devices if this information helps. I was hoping there was a variable at the application level, or a library that could be used but I was unable to find anything. I know there's a pop up when you try to login/ go online to the code when a user is already logged in, so the system does provide an indication that it knows already online, but has no access to a value from what I can see. Any help is appreciated
Last updated: 2024-04-22

Post by jinlee on Camera Feed (CCTV) ^{CODESYS Forge talk (Post)}
Hi, Thanks for the information. However, I can't download the associated project.
Last updated: 2024-09-12

Post by ballen on I have errors while building the project ^{CODESYS Forge talk (Post)}
Any luck at solving this issue?
Last updated: 2024-10-14

Post by jeroenaero on CodeSys Raspberry pi I2C driver not found ^{CODESYS Forge talk (Post)}
I included a project archive in the attachments
Last updated: 2024-11-09

Post by pernockham on PHOENIX CONTACT Axioline PLCnext project in CodeSys SodftPLC ^{CODESYS Forge talk (Post)}
Pretty much my configuration, see attached.
Last updated: 2025-09-09

Post by ph0010421 on Add device greyed out ^{CODESYS Forge talk (Post)}
Click on NET in the project tree and add it there.
Last updated: 2023-12-19

Post by yann2021 on Errors by Code Generate ^{CODESYS Forge talk (Post)}
Maybe could the project file help....
Last updated: 2024-02-17

Post by chir on SMC_REGULATOR_OR_START_NOT_SET issue ^{CODESYS Forge talk (Post)}
Drive: Inovance MD520 In a project I add SoftMotion CiA402 Axis
Last updated: 2024-04-22

Post by eschwellinger on 3.5 P20 hangs - no response ^{CODESYS Forge talk (Post)}
In which situation does this happen? With a special project?
Last updated: 2024-04-22

Post by installwhat on Camera Feed (CCTV) ^{CODESYS Forge talk (Post)}
https://www.youtube.com/watch?v=y_l2siXY7dA check the project from this video
Last updated: 2024-06-23

Post by vtec35 on search runtime 4.9.0.0 for pi 3 ^{CODESYS Forge talk (Post)}
if you prefer i can share the project directly
Last updated: 2025-10-26

Post by ryandmg on Web Client (HMI) Disconnects from Webvisu (Weidmuller u-OS) ^{CODESYS Forge talk (Post)}
Thanks So Much for the reply! Were using the Weidmuller UV66-ADV-10-CAP-W The HMI is pointed to the URL which is assigned through u-OS. Basically when you log into the controller's webserver via browser you can view the installed apps. One of which is the Codesys runtime. When you click on that it takes you to the visualization. That corresponding url is what the HMI is looking for. I apologize I don't have that on hand as I'm in the office right now. I don't think I tried connecting using the port you mentioned and https in lieu of the u_OS URL. I can certainly try. Out of the box the u-OS is set for HTTP. Since we're isolated I havent changed that yet. When this has happened while logged on via chrome on my laptop, simply refreshing brings the visualization right back. In the case of the HMI in kiosk mode, we power cycle the HMI to force a reconnect, log back in u-OS and the visualization is back.
Last updated: 2023-09-06

Post by gmau on RS232 Communication in CODESYS Control RTE V3 ^{CODESYS Forge talk (Post)}
Hello, I would like to implement RS232 communication into CODESYS Control RTE V3. I was writing the program testing it on CODESYS Control Win V3, where it worked fine. When I changed it to RTE, the communication was on, but I cannot send the data between PLC and scale - there is no or little response from scale - mostly one time receive and that is it. On Win V3 it was working fine. I read that I am supposed to configure CODESYSControl file for a proper communication using RTE, but even after that I can not get a stable and working communication. I am attaching my CODESYSControl and CODESYSControlUser data below, as well as I am sending the code from communication function. The communication should be through COM1 port of PC. CODESYS Version: CODESYS V3.5 SP21 + (64-bit) Runtime + Version: CODESYS Control RTE V3 Version 3.5.21.0 / CODESYS Gateway V3 - x64 Version 2.5.21.0 I would be much gratefull for any help. Sincerely,
Last updated: 2025-07-16

Sort by relevance or date