Post by rossanoparis on How to configure CODESYSControl_User.cfg in order to use a specific network card for OPCUA Server ^{CODESYS Forge talk (Post)}
Thank you @eschwellinger Even tough I think the content of the link you provided is a bit messy. To bind OPCUA server to a specific adapter, I should have had insert the following section. [CmpOPCUA] NetworkAdapter=eth0 But it doesn't work, I had to insert the following section instead to get the right configuration. [CmpOPCUAServer] NetworkAdapter=eth0 Regards Rossano
Last updated: 2023-08-29

Post by andrax on Mux I2C ^{CODESYS Forge talk (Post)}
the TCA9548a does not work in Codesys. In Pyton this is only queried once and in Codesys cyclically. Of course you can also insert a terminating resistor in each port, then you should have no problems. I use this one: https://botland.de/8-bit-multiplexer/12723-qwiic-mux-breakout-8-kanal-modul-mit-i2c-multiplexer-tca9548a-sparkfun-bob-16784-5904422341428.html You can simply set the library to the latest version. You do not need Oscat. Do you need an example project for the BMP280?
Last updated: 2024-01-02

Post by andrax on Mux I2C ^{CODESYS Forge talk (Post)}
the TCA9548a does not work in Codesys. In Pyton this is only queried once and in Codesys cyclically. Of course you can also insert a terminating resistor in each port, then you should have no problems. I use this one: https://botland.de/8-bit-multiplexer/12723-qwiic-mux-breakout-8-kanal-modul-mit-i2c-multiplexer-tca9548a-sparkfun-bob-16784-5904422341428.html You can simply set the library to the latest version. You do not need Oscat. Do you need an example project for the BMP280?
Last updated: 2024-01-02

Post by tvm on multiply gives negatives ^{CODESYS Forge talk (Post)}
It's probably because you have an INT in the input to the MUL function, which will then try to output an INT as well. INT variables can only handle values of -32768 to 32767. Your value of 523000 won't fit in an INT, so it turns into an invalid number. Use a DINT. This is usually better for working with time values anyway, because time values are all 32 bit. Or if you can't, use INT_TO_DINT(gvlp.detectie_nalooptijd_s) in the input to the MUL function.
Last updated: 2024-01-04

Post by matt-s on HMI Pushbutton/Move Instruction ^{CODESYS Forge talk (Post)}
I have not gotten to the bottom of this yet no. I have double check that the variables are correct linked. When online with the program I can see the button and rung going true for the move instruction, yet it does not change. Forcing the bit in the program does change the value in Groov View. I am kind of at a loss here, especially since the other POU(For the pumps) does the same thing fine.
Last updated: 2024-02-02

Post by thomasrohnerch on Color Change for Symbols not working ^{CODESYS Forge talk (Post)}
I have some Symbols from the Visualization Toolbox on my Target Visu on the Computer. I tried many Symbols, mainly Arrows. I'm able to control the visibility with condition e.g. "GVL.actual_testvalues.speed <= 0" But I can't do "Toggle color" with boolean GVL.b_toggle_color. Neither "TRUE" nor "FALSE" does change anything. Is this a known issue? I'm using CODESYS V3.5 SP19 Patch 5 + (64-bit). See attached file with more Version-Info. I'm currently using Style 6, Gradient axial 2, 3.5.12.0. I had the same issue with Default 3.5.16.0.
Last updated: 2024-02-08

Post by bschraud on Zielsystem stimmt nicht mit dem verbundenen Gerät überein ^{CODESYS Forge talk (Post)}
Der Eintrag in /etc/CODESYSControl.Usr.cfg war schon vorhanden. Bisher habe ich das Gerät Pi MC SL verwendet. Laut H. Zenker ist das die "Produktionsversion“ der Raspberry-Laufzeitumgebung. Gibt es kein MC SL Runtime Package mehr? Ist dieses in der Standardinstallation nicht mehr vorhanden und muss manuell installiert werden? Beim Wechsel auf Pi 64 kann ich nicht mehr kompilieren wegen folgender Fehlermeldung: "cmperrors interfaces, 3.5.5.0 (system): C0338: Die Bibliothek 'cmperrors interfaces, 3.5.5.0 (system)' wird nur in 32-Bit-Applikationen unterstützt" Vielen Dank für die Hilfe
Last updated: 2024-03-11

Post by timvh on Device logon problem following fresh install ^{CODESYS Forge talk (Post)}
In your project you selected the "CODESYS Control Win V3" as device, but the device you want to connect to is a "CODESYS Control Win V3 x64". Those are not the same. If you double click on the device during the network scan, you will get information that these are not the same, but that you can change the type in your project to the x64 bit type. Another option is to "right-click" on the device in the device tree of your project and select "update device" then select the x64 type.
Last updated: 2024-03-19

Post by superjojo2002 on Licensing info not available. ^{CODESYS Forge talk (Post)}
I checked it using the very same docker container version like colleague moon and the command returned root@nt0001c02c5533:/# cmu -x cmu - CodeMeter Universal Support Tool. Version 7.60c of 2023-Aug-09 (Build 5625) for Linux/ARMHF 64-Bit Copyright (C) 2007-2023 by WIBU-SYSTEMS AG. All rights reserved. Result: 0 CmContainer(s) listed. (CodeMeter not running) Please consider that we intend to license a codesys ARM64 SL in a docker container.
Last updated: 2024-03-20

Post by dkugler on Alarm State Icon ^{CODESYS Forge talk (Post)}
thank you for pointing me to this "bug"!! I haven't recognized, the bit is reset after the first alarm is gone. I use this only for warnings, so it's not a drama, but was not correct in the past. I solved it now simply stupid by counting up a variable every time an alarm appears and decreasing it if an alarm is gone. The "warning lamp" is activated by checking the counter is > 0 The nice side effect, i'm able to show the number of active alarms in the state line now.
Last updated: 2024-04-24

Post by miodusy on CODESYS Control Standard S and Beaglebone ^{CODESYS Forge talk (Post)}
Hi, CODESYS Control Standard S + CODESYS Visualization L, CODESYS Control for Beaglebone 4.11.0.0, CODESYS V3.5 SP20 + (64-bit) I have problem that license manager say that this device is not supported when i try active whole license. When I select only runtime and communication it is go next step, but then I no have license on in Visualistion section, all of rest of software metric licese is ok(IO, Istances of com et, code size etc.). Thanks!
Last updated: 2024-05-11

Post by ndzied2 on Rounding error in simple addition ^{CODESYS Forge talk (Post)}
This is a consequence of how computers store floating point numbers. 0.1 cannot be exactly represented in a computer. This is not a CoDeSys thing. Here is a link to a converter to show you the exact value that is represented when you use a REAL data type (which is a 32 bit float). https://baseconvert.com/ieee-754-floating-point If you really need to keep track of 0.1 increments. use INT OR DINT and then add 1 each time and assume that there is one decimal place.
Last updated: 2024-05-24

Post by liamb on Converting CANbus to Decimal from signed 2's complement ^{CODESYS Forge talk (Post)}
I need to combine two 8 bit CANbus messages to 16 bits signed int then convert to decimal Decimal from signed 2's complement. I've been using the below code to read for new messages, combine them then assign them to a variable What is the best way to do this for from signed 2's complement? fbRxMessage351(Data := RxMessage351Data); IF fbRxMessage351.NewMessage THEN ChargeVoltage := (WORD_TO_REAL((RxMessage351Data[0]) + ((RxMessage351Data[1]) * 256))) * 0.1; END_IF
Last updated: 2024-08-16

Post by pietrobalint on Retain / Persistent Variables in Codesys for Raspberry Pi ^{CODESYS Forge talk (Post)}
Hi micik, I am not sure I am using well the code, because I checked the directory and there is no retains.ret file. Now I deleted the code from my project and the values are still works as persistant variables after ssh reboot it seems to me they retain as their previous value. So I am a bit confused, maybe 4.12.0.0 Raspberry Pi SL solved the persitent variable problem...
Last updated: 2024-08-20

Post by s1ack on PFC200 Will soft-container & IIoT license survive a firmware update? ^{CODESYS Forge talk (Post)}
I have an IIoT License activated on a PFC200 with older firmware 2.08.32 (11). If I flash it to the latest available 4.05.10 (27) does the license get destroyed? I have a back up file '3SLicenseInfo.tar'. But this looks quite a bit different form the backup I got from more modern firmware... 'CMLicenseNew.WibuCmRaU'. Can the new license manager restore it from the old .tar?
Last updated: 5 days ago

Post by garrian on How to write multiple coils (Modbus FC15) ^{CODESYS Forge talk (Post)}
Thanks! As far as I can see, the client can only send words. And on the server side there are an array for each of the functions: bool for coil and discrete, word for holding and input registers. I assume I can use holding register, then use bit mapping on the words instead of coils. But I really want to use the FC15/coils.
Last updated: 14 hours ago

Post by arnaud on eCockpit - unable to start simulation ^{CODESYS Forge talk (Post)}
Hi there! I'm using eCockpit WAGO software to develop HMI's for multiple projects. As I recently starting this, my knowledge on the software is somewhat limited (so maybe my question is a simple one). For most of my projects I can simulate the application and start it to test the code and HMI. However for two projects, I can initiate the "simulation activation" but I cannot start it. Nothing happens when I press start and the visualization shows "The online visualization is waiting for connection. please start the application". - I don't see any errors in the messages - Initially the project are made by a colleague, which moved on. I guess I'm forgetting something, like missing a setting. I appreciate any help I can get. If you need more information to help me out, let me know. Thanks!
Last updated: 2023-08-25

Post by riccardo on Management of a PLC network from a remote station ^{CODESYS Forge talk (Post)}
Goodmorning, I would need to set a control station that can manage a PLC network. In short I need to access to all visu programmed in any PLC of the network (LAN). I was thinking to use a PLC with buttons that call, by mean an IP address, the visu of any PLC. I don't know if it is possible but I saw that there is a RemoteVisuTarget that run CODESYS Control Win V3. Can someone suggest me how to create a remote main control station from a normal PC? Thanks, Riccardo
Last updated: 2023-11-27

Post by sawicpx on CANbus Remapping PDOs During Runtime ^{CODESYS Forge talk (Post)}
Hello, I am working on an application where I need to remap PDOs to a different CANopen object during runtime depending on what value is at a specific register. I have gotten to the point where I put the device into Preoperational State using the CIA405.NMT function. I then reconfigure the PDO 180x and 1a0x obejcts usings SDOs to point to a new canopen object on the device however when I go to restart the Device from PREOP to OP using the CIA405.NMT function the device is reset back to the original configuration as per the initial setup. I am wondering is there any way to change the PDOs at runtime is there some more functionaility I can access to do this. Any direction is appreciated!
Last updated: 2023-12-22

Post by joanm on Programmatically change the IP addresses of the Modbus TCP slave devices ^{CODESYS Forge talk (Post)}
Hello all, I am working in a project in which there are multiple Modbus TCP slaves. I need to be able to change the IP addresses of those devices from the HMI and I was planning to use the process depicted here: https://faq.codesys.com/display/CDSFAQ/Modbus+TCP+Slave%3A+Dynamic+Setting+of+the+IP+Address I can see the port number is what is used to specify which slave device we want to modify the IP address of. This said, can I freely set arbitrary port numbers to each device? I mean, can I set the first device to be at port 502, the second one at port 503... Any drawback or restriction? Is there any other way to reference to the device without having to change the port numbers? Thank you all in advance.
Last updated: 2024-01-04

Post by toby on Ethercat Servo Setup ^{CODESYS Forge talk (Post)}
Hi everyone, so a little update to this, I've come back to this project in the new year, and got it working. Yeah!, However, now with the new licensing setup, I need a new SoftMotion license, but it doesn't seem to be compatible with the previous Raspberry Pi SL license. Has anyone had any luck with Raspberry Pi and SoftMotion_Lite? Specifically the licensing of such? My customers new installation needs to be rebooted every 30min which is causing headaches! Another option is to not use the SoftMotion function blocks, and control the EtherCat amplifier directly, but I'm not sure how to do so. Does anyone have a specific example project of how to control a servo without the use of the SoftMotion function blocks? Thanks everyone for any assistance rendered. It's very much appreciated! Toby
Last updated: 2024-01-10

Post by ewi04 on How to upload application file to remote controller (offline) ? ^{CODESYS Forge talk (Post)}
Thank you very much for your time and replay! Sounds like a good idea. Unfortunately, I have no other option to run the code from the running plc. So, I can’t stop any services. If anyone has the same problem, I've gotten a little closer to understanding it: Sometimes the copied files are empty after the restart. The update code checks if there are any empty files. Before I turn off the device, everything is okay. But after starting, some files are suddenly empty and that cause the problems. I don't know why this happens.
Last updated: 2024-02-16

Post by amy123 on codesys mqtt publish serialization ^{CODESYS Forge talk (Post)}
Hello, I am using the CODESYS IIoT Libraries SL MQTT Publish. Does this publish block only support publishing STRINGS as a readable format? I can publish ENUM, STRUCT, BOOL; however, MQTT Explorer will only display strings. When I use Wireshark, I can see that it is publishing something, but it looks to be publishing a serialized version which is a bunch of 0s or random text. If so, is there any way to deserialize this information back into a readable format? See pictures, where I have a BOOL TRUE that gets published as 001. Then see where I publish a STRUCT and it's an incomprehensible combination of 0s - only the string variable is displayed. Or, is it expected that you convert everything to a string before publishing? Any help is greatly appreciated! :)
Last updated: 2024-02-16

Post by nmcc on Viewing PDF in WebBrowser Visual Element ^{CODESYS Forge talk (Post)}
I am trying to show a PDF in a WebBrowser element. I have the file saved to the drive of the HMI/PLC. I am linking it in the URL parameter of the WebBrowser using the following directory link. 'http://localhost:8080/$$sdcard$$/FileName.pdf'. This allows for the program to download without any errors. When I navigate to that screen it is just a white box and nothing shows. I attempted putting the same link in the show parameter and I get a loading icon on my cursor when monitoring the HMI with my PC. Any help is appreciated. Thank you.
Last updated: 2024-02-29

Post by francescoc on Logger in ms ^{CODESYS Forge talk (Post)}
Hi, I cannot find any documentation regarding the codesys configuration file. I modified this part to have log files saved to disk: [CmpLog] Logger.0.Name=LOGS/PlcLog Logger.0.Filter=0xFFFFFFFF Logger.0.Enable=1 Logger.0.MaxEntries=20000 Logger.0.MaxFileSize=5000 Logger.0.MaxFiles=10 Logger.0.Backend.0.ClassId=0x0000010B ;sends logger messages to SysOut Logger.0.Backend.1.ClassId=0x00000104 ;writes logger messages in a file Logger.0.Backend.2.ClassId=0x00000135 ;sends logger messages as UDP syslog Logger.0.Type=0x314;Set the timestamp to RTC ;Logger.1.Name=/tmp/CommLog ;Logger.1.Enable=1 I need to have milliseconds in the timestamp as well. What value should I use instead of 0x314? Is there any documentation regarding this file? Thank you
Last updated: 2024-03-16

Sort by relevance or date