Post by yannickasselin on MQTT QoS 1 & 2 ^{CODESYS Forge talk (Post)}
Using Wireshark, I can see that the broker sends the QoS 1 or 2 messages when Codesys MQTT client reconnects but they are just discarded and not acknowledged by Codesys MQTT Client. So the broker holds on to them and tries to send them back to Codesys every time the client reconnects but they are always discarded by Codesys. There really seems to be an issue with QoS 1 & 2 in Codesys. It really does not behaves like it should.
Last updated: 2024-10-31

Post by scoob on ModbusFB - Slow Response Time ^{CODESYS Forge talk (Post)}
Hello, I have been trying to use the ModbusFB functions so I can put some code into libraries, but it seems to be very slow for me. I have a Modbus device with 100ms registers. I previously setup 10 channels in the 'traditional' Modbus Slave with channels and mappings - and set a cyclic trigger at 100ms - this worked fine. I then tried the ModbusFB example, and setup reading the same 10 blocks of modbus addresses, copying the example and putting all of the requests into an array and triggering the requests sequentially. I timed how long the requests are taking to get round to each one, and it is around 1s 450ms. How do I speed this up to match the cyclic time? IF NOT(init) THEN init := TRUE; // Set the required IP address: ipAddress[0] := 192; ipAddress[1] := 168; ipAddress[2] := 1; ipAddress[3] := 10; // Pass the required IP address to the clinet FB: client_NetworkSwitch.aIPaddr := ipAddress; client_NetworkSwitch.udiLogOptions := (ModbusFB.LoggingOptions.ClientConnectDisconnect OR ModbusFB.LoggingOptions.ClientReceivedValidReplies); // Try to connect the client client_NetworkSwitch(xConnect:=TRUE); // Configure all the channels to read connecting them to the client: portStatus_Request(rClient := client_NetworkSwitch, uiStartItem := 4096, uiQuantity := 32, pData := ADR(portStatus), udiReplyTimeout := udiReplyTimeout); portSpeed_Request(rClient := client_NetworkSwitch, uiStartItem := 4352, uiQuantity := 32, pData := ADR(portSpeed)); flowControl_Request(rClient := client_NetworkSwitch, uiStartItem := 4608, uiQuantity := 32, pData := ADR(flowControl)); linkUpCounter_Request(rClient := client_NetworkSwitch, uiStartItem := 5888, uiQuantity := 32, pData := ADR(linkUpCounter)); txPacketCounter1_Request(rClient := client_NetworkSwitch, uiStartItem := 8192, uiQuantity := 100, pData := ADR(txPacketCounter1)); txPacketCounter2_Request(rClient := client_NetworkSwitch, uiStartItem := 8292, uiQuantity := 28, pData := ADR(txPacketCounter2)); rxPacketCounter1_Request(rClient := client_NetworkSwitch, uiStartItem := 8448, uiQuantity := 100, pData := ADR(rxPacketCounter1)); rxPacketCounter2_Request(rClient := client_NetworkSwitch, uiStartItem := 8548, uiQuantity := 28, pData := ADR(rxPacketCounter2)); txErrors_Request(rClient := client_NetworkSwitch, uiStartItem := 8704, uiQuantity := 64, pData := ADR(txErrors)); rxErrors_Request(rClient := client_NetworkSwitch, uiStartItem := 8960, uiQuantity := 64, pData := ADR(rxErrors)); // Trigger all client requests initially FOR clientRequestsCnt := 0 TO (SIZEOF(clientRequests)/SIZEOF(clientRequests[0]))-1 DO pClientRequest := clientRequests[clientRequestsCnt]; pClientRequest^.xExecute := TRUE; END_FOR // Prepare sequential trigger / control of client requests. clientRequestsCnt := 0; pClientRequest := clientRequests[clientRequestsCnt]; END_IF // Call the client to do request processing: client_NetworkSwitch(); // Now we trigger client request sequentially ... IF NOT pClientRequest^.xExecute AND NOT pClientRequest^.xDone AND run AND client_NetworkSwitch.xConnected THEN pClientRequest^.xExecute := TRUE; END_IF // .. and check result/error IF pClientRequest^.xExecute AND run AND client_NetworkSwitch.xConnected THEN IF pClientRequest^.xDone THEN // Prepare next trigger of client request (a rising edge of xExecute) pClientRequest^.xExecute := FALSE; IF clientRequestsCnt < SIZEOF(clientRequests)/SIZEOF(clientRequests[0])-1 THEN // next client request clientRequestsCnt := clientRequestsCnt + 1; ELSE clientRequestsIterationCounter := clientRequestsIterationCounter + 1; clientRequestsCnt := 0; END_IF pClientRequest := clientRequests[clientRequestsCnt]; END_IF END_IF I did try a semi-coded way using the IoDrvModbusTCP library, and setting the slave com settings, then 10 commands and 10 requests, then using a TP on xDone as a pause, before triggering another request - this is time the delay is around 120ms - so the device is fine with the speed, just something I am doing wrong in the ModbusFB method I am sure.
Last updated: 2024-04-26

Post by timvh on Stack overflow with really simple function ^{CODESYS Forge talk (Post)}
You have declared the function block in a function and call the instance also from a function. This is not correct, because a function is initialised with every call. The http client function block should be declared as Global Variable if you want to cal it from a Function, but probably it is better to declare it in a Program and also call the instance of the http function block from the same Program.... The variables of a Program are not initialised with each call.
Last updated: 2024-09-20

Post by garrian on How to write multiple coils (Modbus FC15) ^{CODESYS Forge talk (Post)}
Thanks for your reply. I belive it is contiguous, I'm writing to adress 0 to 4. Or, do you mean something else? Well, something is happening. If I on the client set adress 1,2,3 to true, only 1 is set to true on the server side. On the client side, the data is array of word. But on the server side, the coils are array of bool. Holding register is array of word on server side. Can this be a problem? Attached screenshot of how it looks at the server side.
Last updated: 2024-11-17

Post by dekelec on Codesys 2.3 & Peak PCAN ^{CODESYS Forge talk (Post)}
IF you have an USB interface type in "Peak_USB" for CAN card driver (Name of CAN card driver). No need to add libraries for communication via CoDeSys Gateway. For other card types contact PEAK support and they will help you. Regards,
Last updated: 2024-07-08

Post by hclai on Table Content with Multilanguage ^{CODESYS Forge talk (Post)}
I have an data structure which intend to list in a table and let user to add the content to the table. How can we able to support for displaying different language in the content of the table? which is dynamic to the user input.
Last updated: 2024-01-10

Post by timvh on Error: C0138: No matching 'FB_Init' method found for instantiation of VisuClientObjectMgr ^{CODESYS Forge talk (Post)}
Maybe check: - The library manager, are you maybe missing some libraries - Tools - CODESYS installer: update the CODESYS Visualization and Visualization support - Project - Project environment: maybe you need to update the visualization profile
Last updated: 2025-11-27

Post by r-niedermayer on Collapse all ^{CODESYS Forge talk (Post)}
Basically, Codesys does support the Windows shortcuts: such as the " * " and " / " as well as the " + " and " - " Numpad keys to expand or collapse folders and subfolders or the element. This affects both, the objects in the device tree and the folding structures in f.e. the ST editor.
Last updated: 2024-11-21

Problem with FBD/LD and "Go to the definition" of a Method ^{CODESYS Forge talk (Thread)}
Problem with FBD/LD and "Go to the definition" of a Method
Last updated: 2012-02-10

SM3_Robotics, time and distance remaining until the end of a group motion. ^{CODESYS Forge talk (Thread)}
SM3_Robotics, time and distance remaining until the end of a group motion.
Last updated: 2021-07-09

Buyer guide for first robot arm and need of general tips for beginner. ^{CODESYS Forge talk (Thread)}
Buyer guide for first robot arm and need of general tips for beginner.
Last updated: 2021-01-25

read SVN-revisions of project and library insinde a library function ^{CODESYS Forge talk (Thread)}
read SVN-revisions of project and library insinde a library function
Last updated: 2018-05-16

Access to a GVL and seraching for a variable inside of it (Pyhton) ^{CODESYS Forge talk (Thread)}
Access to a GVL and seraching for a variable inside of it (Pyhton)
Last updated: 2022-07-25

Bug found? Weird behaviour of Combobox (Array and Integer) in CodeSys 3.5SP16 Patch 2 (64bit) Visu ^{CODESYS Forge talk (Thread)}
Bug found? Weird behaviour of Combobox (Array and Integer) in CodeSys 3.5SP16 Patch 2 (64bit) Visu
Last updated: 2021-11-02

Is it possible to send SDOs and sync manually independend of the manager status? ^{CODESYS Forge talk (Thread)}
Is it possible to send SDOs and sync manually independend of the manager status?
Last updated: 2022-04-01

SM3_Robotics, time and distance remaining until the end of a group motion. ^{CODESYS Forge talk (Thread)}
SM3_Robotics, time and distance remaining until the end of a group motion.
Last updated: 2021-07-09

Codesys for linux SL AMD64 and last update of UBUNTU 22.04 ^{CODESYS Forge talk (Thread)}
Codesys for linux SL AMD64 and last update of UBUNTU 22.04
Last updated: 2023-02-06

Using a raspberry pi and NVLs to log variables outside of Codesys ^{CODESYS Forge talk (Thread)}
Using a raspberry pi and NVLs to log variables outside of Codesys
Last updated: 2025-11-21

Trend legend naming and access/config to/of trend/legend-variables ^{CODESYS Forge talk (Thread)}
Trend legend naming and access/config to/of trend/legend-variables
Last updated: 2025-12-22

Post by tjacks on Opc UA Data Source Client Browse Error in Codesys HMI ^{CODESYS Forge talk (Post)}
Codesys V3.5 SP21 Patch 3 Codesys HMI 3.5.21.30 I'm trying to connect to an OPC UA server on a Kuka robot controller using Codesys HMI's data source manager. I get through the login phase and the client browses most of the data structure on the server but errors out toward the end with a generic: Error while browsing the client, Failed with service result: BadUnexpectedError. If I complete the data source setup and try to update variables, I get the attached stack trace for the error. I've tried several different endpoint and security options. Most get me through the login but all error out while browsing. UA Expert happily connects and browses with the same configuration. I've connected this same version of Codesys to TwinCAT OPC UA servers and Siemens PLC OPC UA servers. Any ideas on what may be causing the generic BadUnexpectedError during OPC UA server browse?
Last updated: 2025-11-17

Post by tcarlbom on codesys sp20 opcua not working ^{CODESYS Forge talk (Post)}
hi, anyone else having trouble with opc ua in codesys sp20? i get Error 'BadIdentityTokenInvalid' was returned during ActivateSession i have tried both windows x64 runtime and linux runtime. i have created a completely new codesys project for this. in each of them i have only added the symbol configuration and selected one tag. i have tried several opc ua client, like ua expert, nodejs and python. all return Error 'BadIdentityTokenInvalid' was returned during ActivateSession so the problem must be the opc ua server.
Last updated: 2024-07-03

Post by fmon on Modbus : dis- / re-connect cable: modbus does not re-start ^{CODESYS Forge talk (Post)}
Hello, I am using codesys Modbus TCP client (4.4.0.0) to communicate with a python modbus server (package pyModbusTCP). I first start my python server on the distant machine. After a fresh codesys compilation, a plc connection/transfer and a PLC run, the modbus connection is OK. Every time in this context the connection is created correctly. When I shut down the server, the modbus connection falls, that is normal. When I restart the python server, impossible to recreate the modbus connexion. With the client autoreconnection, I see on my server that the client tries to connect but unsuccesfully. I have the following message : DEBUG:pyModbusTCP.server:accept new connection from ClientInfo(address='192.168.1.20', port=33476) DEBUG:pyModbusTCP.server:Exception during request handling: NetworkError('recv return null') I tried to stop the codesys client and to restart it with these commands : Modbus_TCP_Client.xStop := True; // Or False Modbus_TCP_Client.Enable := True; // Or False Modbus_TCP_Server.Enable := True; // Or False I tried to confirm the error manually to force reconnection with: Modbus_TCP_Server_Motors.xConfirmError := TRUE; I tried also this command to STOP/RESET/START client and server (codesys side) but nothing happens : status_client := Modbus_TCP_Client.SetCommunicationState(eRequestedState := DED.DEVICE_TRANSITION_STATE.STOP); // .RESET & .START The answer of this function when executed is "status_client = NOT_SUPPORTED" It seems that is a socket problem, but I do not understand if it is on the client or server side. I tried a modbus simulator called "ananas.exe" and the result is the same. Impossible to get a modbus reconnection. What is different at the first connection and at a reconnection attempt ? Thanks for your help
Last updated: 2025-03-14

Post by konstantin on Lenze i950 Servo and WAGO PFC200 ^{CODESYS Forge talk (Post)}
Hello, basically the i950 drive support CiA402 Basic and CiA402 Advanced modes. I attached pictures of both mode supported functions. It also support CSP, VL, CSV and CST modes. It seems the homing mode is in CiA402 Advanced mode but how can you not have the homing mode in both modes? It is a vital part of any servo system. If I use the SoftMotion standard demo mode, I can move the servo absolute and relative but cannot home it. But in SoftMotion Light mode, I cannot execute any motion function. Here is the official manual for i950 servo drive - i950 Documentation Best Regards Konstantin Kolev
Last updated: 2026-02-13

Post by ofey on OPC server crash ^{CODESYS Forge talk (Post)}
Hi! I repeatly encounter a crash of the OPC server, which forces a reboot of the controller with frequent connect/disconnect to the server. Have any of you encountered this before? And is it a workaround? ie. deny that particular client connection by timeout or similar instead of crashing the PLC? This is during a development phase of the user interface. Up to 3 others connect/disconnect frequently to test their code. It is a bit troublesome of the PLC crashes several times a day because of this :( I greatly appreciate all comments. I hope it exists a fix for this, or something that hinders the crash. I attached the logfile for the crash
Last updated: 2024-11-26

Forge 🇬🇧 ^{CODESYS Forge talk (Discussion)}
Discussions about CODESYS Forge projects and features of the CODESYS Forge website
Last updated: 2026-02-14

Sort by relevance or date