Post by esave on Stepper Drive with Ethercat ^{CODESYS Forge talk (Post)}
I bought and installed SoftMotion Light now. When I try to add a SoftMotion Light Axis to my stepper drive and I go online it shows: "The license is missing or invalid". See picture What am I doing wrong? This is the right way right? First add your EtherCat XML-File from your stepper driver and then add the SoftMotion Light axis right? Thanks for your help esave
Last updated: 2024-04-25

Post by wiresplus on Display minutes as hours & minutes ^{CODESYS Forge talk (Post)}
Hello, I have a counter that increments an INT value once per minute I want to display this value in Minutes until 60, then Hours/Minutes thereafter on the HMI Codesys V3.5 SP16 I can divide the minutes by 60 to get hours, but then the minutes is still more than 60. Example: a process has run for 350 Minutes. I need to display "5 Hours 50 Minutes" But if it's only been 45 Minutes, I don't want "0 Hours 45 Minutes" , just "45 Minutes"
Last updated: 2024-05-25

Post by yofi on Configuring an Encoder ^{CODESYS Forge talk (Post)}
I have a raspberry pi trying to add encoder to it using that free encoder node. I simply dont understand where the encoder channel A/B suppoded to be mapped when i got to I/O mapping on encoder I get nothing to where to set the channels for the encoder or is there any blocks from a library or how is it that you use an encoder with Codesys it doesn't seem clear at all
Last updated: 2024-05-25

Post by kris-samoy on Get Alarm status in Codesys ^{CODESYS Forge talk (Post)}
I am rather new to Codesys and I'm trying to figure out how to get the status of an alarm. This to interlock the start of a device until the alarm has been acknowledged... I am not sure if IAlarm.GetState (METH) can be used for this purpose. If yes then could someone please briefly explain how to use this? https://content.helpme-codesys.com/en/libs/AlarmManager/4.1.0.0/Interfaces/pou-IAlarm/GetState.html Thx & grtz, Kris
Last updated: 2024-06-03

Post by installwhat on C0077 on one machine but not another ^{CODESYS Forge talk (Post)}
https://forge.codesys.com/forge/talk/Engineering/thread/92c913bf7c/ Solved by changing the ethercat master version after reading the thread linked above. I think I need to read up on why this happened. I understand that placeholders should point to a particular version for obvious reasons however what has occurred in this instance is different. The example project was released as a "project archive" but it seems to load differently based on what I've got installed in my repositories. I'm going to dig into that tomorrow but any advice is welcome.
Last updated: 2024-06-11

Post by ranadheer on Request to share documents about SoftPLC Extension SL ^{CODESYS Forge talk (Post)}
Hello Everyone Our team is planning to begin an industrial automation project and we are currently evaluating the use of SoftPLC Extension SL as a potential solution. As we are in the early stages and have yet to start the implementation, we kindly request access to official reference documents, technical manuals, and datasheets relating to SoftPLC Extension SL. Thank you very much for your assistance. We look forward to your response.
Last updated: 2025-10-18

Post by scrollman on Attribute FB for comment ^{CODESYS Forge talk (Post)}
Masters, I need your help. I can explain in different way. I can get the name and comment of parameter if i use "VARINFO", but right now I want to get name and comment of FB from inside one. I can get the name to use the "{attribute 'reflection'}" but I don't understand how to get comment? Do you have any idea how to do it? Thanks
Last updated: 2026-01-08

Post by antonz on OSCAT Scale_r function not working in LD 4.60 works in LAD2 on 3.5.21sp3 ^{CODESYS Forge talk (Post)}
That's what I found as well Shaun. I have seen it at least in versions 3.5.21.1 and 3.5.21.3. There seems to be an issue with the FBD/LD package v4.6.0.0. The workaround proposed by Tim works but needs to be done manually on every code change/addition. For now we manually downgrade the FBD/LD package from v4.6.0.0 down to v4.5.0.0 after installation of CoDeSys. Same as you did. I hope this gets fixed on a next patch.
Last updated: 2025-11-21

Post by winki on Error in licence activation ^{CODESYS Forge talk (Post)}
Hello, Despite receiving an activation message after entering the license number, I don’t have any license installed on my gateway. I went to check in /var/opt/codesys/ and there is no License file. I searched the entire gateway for a .lic file and found no license. I’m really stuck—how can I fix this, please? When I am using the licence tools I got this picture: But nothing that have been activated. Loic,
Last updated: 2026-02-03

Post by winki on Error in licence activation ^{CODESYS Forge talk (Post)}
Hello, Despite receiving an activation message after entering the license number, I don’t have any license installed on my gateway. I went to check in /var/opt/codesys/ and there is no License file. I searched the entire gateway for a .lic file and found no license. I’m really stuck—how can I fix this, please? When I am using the licence tools I got this picture: But nothing that have been activated. Loic,
Last updated: 2026-02-03

Post by sahin6033 on DSE M840-001-02: DSEServiceTool transfers CodesysApp.pkg successfully, but device shows “No application loaded ^{CODESYS Forge talk (Post)}
Hi, I am trying to load a test application into a DSE M840-001-02 display, but after reboot the device still shows: “No application loaded” I would like to understand whether the problem is in my project, the package creation process, or firmware/runtime compatibility. Hardware Device: DSE M840-001-02 Firmware used: M840 MKII Firmware File v4.1.2 Software CODESYS V3.5 SP12 (32-bit) DSE CODESYS Package v1.5.44 DSEServiceTool What I did Created a new empty Standard Project Selected target/template: M840-02 V4.1 Used a minimal ST program only: PROGRAM PLC_PRG VAR xAlive : BOOL := TRUE; END_VAR Confirmed: project builds PLC_PRG is assigned to MainTask created Boot Application Generated CodesysApp.pkg Put the M840 into bootloader mode Sent the package using DSEServiceTool DSEServiceTool result Transfer completes successfully and I get: connection accepted 100% download package ACK <status>OK</status> ** Example log:** Searching for controllers.... sendPackageToController: waiting for incoming data connection... sendPackageToController: connection accepted... <status>Downloading</status> <percent>20</percent> <percent>40</percent> <percent>90</percent> <percent>100</percent> sendPackageToController: sent 112cb8 bytes OK Package ...\CodesysApp.pkg transferred to controller c0a80101 OK sendPackageToController: package ACK <status>OK</status> Actual result After reboot, the display still shows: “No application loaded” Additional issue I also saw earlier At one stage I also had these fatal errors in CODESYS: [FATAL ERROR] Unresolved reference: 'IOMGRLOCKENTER' [FATAL ERROR] Unresolved reference: 'IOMGRLOCKLEAVE' I checked library versions and adjusted them to: IoDrvBase = 3.5.5.0 IoStandard = 3.5.10.0 Also, I am using CODESYS SP12, which I understand is the correct version for DSE M840. My questions If DSEServiceTool shows Status OK and package ACK, but the device still says “No application loaded”, does that mean: the .pkg was transferred but not accepted as a valid application? the package was built incorrectly? the boot application / runtime / firmware versions are still mismatched? What is the correct procedure to generate CodesysApp.pkg for M840-02 V4.1? Is there any known compatibility issue between: DSE CODESYS Package 1.5.44 M840 MKII Firmware 4.1.2 CODESYS 3.5 SP12 Has anyone successfully loaded even a minimal empty test project into M840-001-02, and if so, what exact versions/process did you use? Any help would be appreciated.
Last updated: 2026-03-17

Post by tommyk-mar on Smooth path is not working with SMC_NCInterpreter ^{CODESYS Forge talk (Post)}
Hello, Im using SMC_NCInterpreter and SMC_NCReadFile2 to read gcode program for CNC machine and what I have observed is that G51 and G52 is not smoothing the path. Machine stops in every point, what could I do to make machine pass through the points without stopping or what could allow me to use smooth path corretly if I use NCInterpreter. Im using it because I want to add variables to my gcode and its not possible directly from the CNC editor thats why I do use external file. Any ideas?
Last updated: 2026-03-26

Post by darwin03 on Mismatch between coordinate monitor and actual motion using SMC_GroupJog2, MC_MoveLinearAbsolute (6DOF) ^{CODESYS Forge talk (Post)}
Hi Guys!!! I am experiencing an issue when trying to move 6DOF using SMC_GroupJog2 and MC_MoveLinearAbsolute, but I don't understand why, when I jog only X or Y, the coordinate I monitor just changes the X or Y value. It's true, but in reality, Joint6 is still running like the video. Am I wrong somewhere? Many thanks for considering my request.! Video: https://drive.google.com/drive/folders/1vRHQ3AtTO3mijptqZgn5OcP9pyi527Jm?usp=sharing
Last updated: 2026-04-06

Post by kreisfilho on Stop raspberry from executing a plc program ^{CODESYS Forge talk (Post)}
Hi guys, Can someone inform where in a raspberry pi are stored the codesys programs? I´ve been training the use of a RPI as PLC, which works pretty well, however while both the RPI and PC (running codesys) remain connected to the same network. The question is: how to run the codesys program downloaded to the RPI as a stand alone device (disconnected from the PC)? Thanks! Kreis
Last updated: 2023-08-23

new feature: list/view plclogs from the plcs ^{CODESYS Forge talk (Thread)}
new feature: list/view plclogs from the plcs
Last updated: 2023-08-30

Post by aott33 on Webvisu NO load ^{CODESYS Forge talk (Post)}
Thanks, I will check the PLC Log when the PLC is connected again. I will update my findings here. Since I don't have access to the Linux Panel PC at the moment, I tested inside my development VM with the same Linux OS. I have no issues or delays connecting to the WebVisu using my Linux VM. Two main differences: 1. My host Computer has a faster processor compared to the panel PC. 2. There are no devices connected in my dev environment. I will continue testing when I have connection to the panel PC.
Last updated: 2023-09-23

Add Commands in the menu to call specific PY script ^{CODESYS Forge talk (Thread)}
Add Commands in the menu to call specific PY script
Last updated: 2016-06-22

Need help before losing control over myself with the BK1150 ;-) ^{CODESYS Forge talk (Thread)}
Need help before losing control over myself with the BK1150 ;-)
Last updated: 2017-05-31

Compiling CoDeSys project using the command line interface ^{CODESYS Forge talk (Thread)}
Compiling CoDeSys project using the command line interface
Last updated: 2021-01-27

How to control the Amp2 from HifiBerry ? ^{CODESYS Forge talk (Thread)}
How to control the Amp2 from HifiBerry ?
Last updated: 2023-07-04

Where do I find documentation on the libaries in V3.3 ? ^{CODESYS Forge talk (Thread)}
Where do I find documentation on the libaries in V3.3 ?
Last updated: 2010-02-08

Altering default text/fomt size in the IDE? ^{CODESYS Forge talk (Thread)}
Altering default text/fomt size in the IDE?
Last updated: 2014-05-02

The intent of two Library Managers in a Project ^{CODESYS Forge talk (Thread)}
The intent of two Library Managers in a Project
Last updated: 2016-08-22

Post by eschwellinger on Official MQTT-Client: MAX_RECEIVE_BUFFER_SIZE_EXCEEDED ^{CODESYS Forge talk (Post)}
...and reduce the load of the plc
Last updated: 2023-09-26

The required device description is not installed.. ^{CODESYS Forge talk (Thread)}
The required device description is not installed..
Last updated: 2023-10-03

Sort by relevance or date