Post by arnog on Two drives on one axis, Gantry Robot ^{CODESYS Forge talk (Post)}
Hi TK_Jenssen did you found a solution I am setting up the samelike gantry only with two z-axes which are mounted on fix position with an X axes between the two z-axes. The movement and position of both z-axes must be very well aligned and calibrated. Maybe also to be adjusted by programming. Can you sent an example of your solution?
Last updated: 2023-08-25

Post by john-ronald on Communication error (#0), logout performed,please check if plc is connected ^{CODESYS Forge talk (Post)}
Hi, I have the same problem. However I am using ethernet connection not USB. I can ping the PLC and also connect to it via Wago ethernet settings, but I cannot upload using the Codesys 2.3. My PLC is Wago 750-862. The detailed error is - " connect: Connection refused Write attempt from invalid socket. " Any help would be appreciated.
Last updated: 2023-09-11

Post by transmin01 on PCAN serial "No CAN driver found" ^{CODESYS Forge talk (Post)}
Hi, I am using a PCAN mini CAN board which has the Windows drivers installed on the target PLC. PCAN board can be seen in device manager. However, I am getting "No CAN driver found" error. I have read the post https://forge.codesys.com/forge/talk/CODESYS-V2/thread/44aae19318/ and have uncommented the CmpPCANBasicDrv driver in the CodesysControl.cfg file in development PC and have copied it to the target PC. Current CodesysControl.cfg file attached. Is there anything else I am missing? Regards
Last updated: 2023-09-14

Post by manuknecht on Detect "Cancel" Press in FileOpenSave Dialog ^{CODESYS Forge talk (Post)}
When using the FileOpenSave dialog and using the Visu_FbFileListProvider FB as an In/Output I could not manage to detect the difference of pressing the "Load" button on the dialog vs. pressing the "Cancel" button. In both cases, the selected file is updated if the dialog is closed when checking using the Visu_FbFileListProvider.GetSelectedFileName() command. How can I prevent reading or writing of a file when the "Cancel" button was pressed?
Last updated: 2023-09-19

Post by damian177 on Codesys and SMS in RPi ^{CODESYS Forge talk (Post)}
Hi, I try use IIoT library to send and receive SMS by Raspbery PI and Codesys. I installed IIoT package and added the SMS library, But something is wrong, when I init communication it doesn't work, When I sniffer my communication (AT commands) beetwen RS232 RaspberryPi and my GSM modem I have only below commands: AT+CMEE=1 OK AT+CPIN? +CPIN: READY Anyone have idea what can be wrong ?
Last updated: 2023-09-28

Post by sukrit on What licenses are required for runtime on raspberry pi cm4 ^{CODESYS Forge talk (Post)}
We have developed a project for 2 servo motors using raspberry pi computemodule 4 on ethercat master. we are using web visualization for display different screens. project is running well in demo. we want to implement it in production envoirment. being new still wondering which licences i need. Can We get this information in codesys devlopment software. code size is approx 5 mb, 1 instance of etharcat master and aproox 100 variables in visaualization.
Last updated: 2023-10-17

Post by mondinmr on Jitter problems on imx8 ^{CODESYS Forge talk (Post)}
SOLVED!!! In this imx8 max_cstate=1 in kernel boot parameters is not working! We found a workaround: #include <stdio.h> #include <fcntl.h> #include <unistd.h> #include <stdint.h> int main(void) { int fd; uint32_t value = 0; fd = open("/dev/cpu_dma_latency", O_WRONLY); if (fd < 0) { perror("Error opening /dev/cpu_dma_latency"); return 1; } if (write(fd, &value, sizeof(value)) != sizeof(value)) { perror("Error writing to /dev/cpu_dma_latency"); close(fd); return 1; } while (1) { pause(); } } This simple code launched before CODESYS do the same work! Now jitter is identical as measured by cyclictest!
Last updated: 2023-10-19

Post by simotion on Online view : code is scanned ^{CODESYS Forge talk (Post)}
If I do online monitoring of code in f.i. a function block, I cannot see if the function block is called or not. In software from other vendors you normally have an indication if the online code you are looking on is scanned at that moment or not. Is there a way in Codesys to determine in the online view if (parts) of the code are scanned or not? Thanks
Last updated: 2023-10-23

Post by ekristoffe on Beispieldateien finden / Inhalt der Packages ^{CODESYS Forge talk (Post)}
Hello @eschwellinger, Why not using one of those 2 folders: C:\ProgramData\CODESYS C:\Users\Public\Documents\CODESYS The main reason is depending on the company and the user right, the end user may not have the access to use those folders. Also having a non version dependent folder may help if the end user uninstall a previous version and forgot all its sample project where in this previous version installation. Thanks.
Last updated: 2023-11-24

Post by simotion on Inheritance of axis ^{CODESYS Forge talk (Post)}
I have developped a function block 'Axis' the inherits from 'AXIS_REF_SM3' -> FUNCTION_BLOCK Axis EXTENDS AXIS_REF_SM3 In my global variable list I define a variable MasterDrive of type Axis and assign Axis1. Axis1 is a virtual drive (AXIS_REF_VIRTUAL_SM3). This type should inherit from AXIS_REF_VIRTUAL. VAR_GLOBAL MasterDrive : Axis := Axis1; However I get the error 'Cannot convert type'. What is the way to obtain what I want : function block inheriting AXIS_REF_SM3 and initialising this function block with a Softmotion virtual or real axis?
Last updated: 2023-12-07

Post by zatalian on Codesys Control for Raspberry Pi 4.10.0.0 - Raspberry Pi OS > 2023-12-05 ^{CODESYS Forge talk (Post)}
There seem to be problems with the latest version of raspberry pi os 64bit (I used the lite version). The codesys control runtime crashes after a few seconds. The same runtime works on the raspberry pi image from 2023-10-10 When starting the runtime from the commandline, i get the following error: ooops... this runtime was build for RASPBERRYPI. Hardware version or firmware version not supported! (and yes, I'm running this on a raspberry pi :-)
Last updated: 2023-12-11

Post by mg0815 on Codesys Control log "eventbuffer full" ^{CODESYS Forge talk (Post)}
Device: RPI 3b or 3B+ System: Wheezy Codesys: 3.5.16.2 I got the Log: 2023-12-13T00:38:43Z, 0x00000054, 2,6,11, !!!! Warning: Eventbuffer full for app=<app>Application</app>; an inputevent with the tag <tag>128</tag> has been dropped This log happens aroud 10 times a second. Sometimes the controller stopped working any more. What is the reason for this? I will update this controller soon (I hope so, but in the meantime I should at least know hoe to prevent this issue) Mario
Last updated: 2023-12-14

Post by mputaggio on Recipe Manager - RecipeManCommands, load & write wrong values, Bug? ^{CODESYS Forge talk (Post)}
Hello, We encountered the same issues on both recipe library versions 4.2.0.0 and the newest 4.3.0.0. The Arrays of structs get saved correctly but loading them restores only some indexes, while others get lost or completely wrong. We have been using the same recipes for the last two years on recipe manager vers. 3.5.17 withoud issues. There also seems to be a different behaviour in vers. 4.3.0.0 but it's still incorrectly loading the recipes. Did you find any workaround or solution? Codesys version used: 3.5.19.50
Last updated: 2023-12-15

Post by andrax on Mux I2C ^{CODESYS Forge talk (Post)}
the TCA9548a does not work in Codesys. In Pyton this is only queried once and in Codesys cyclically. Of course you can also insert a terminating resistor in each port, then you should have no problems. I use this one: https://botland.de/8-bit-multiplexer/12723-qwiic-mux-breakout-8-kanal-modul-mit-i2c-multiplexer-tca9548a-sparkfun-bob-16784-5904422341428.html You can simply set the library to the latest version. You do not need Oscat. Do you need an example project for the BMP280?
Last updated: 2024-01-02

Post by andrax on Mux I2C ^{CODESYS Forge talk (Post)}
the TCA9548a does not work in Codesys. In Pyton this is only queried once and in Codesys cyclically. Of course you can also insert a terminating resistor in each port, then you should have no problems. I use this one: https://botland.de/8-bit-multiplexer/12723-qwiic-mux-breakout-8-kanal-modul-mit-i2c-multiplexer-tca9548a-sparkfun-bob-16784-5904422341428.html You can simply set the library to the latest version. You do not need Oscat. Do you need an example project for the BMP280?
Last updated: 2024-01-02

Post by eschwellinger on Edge Gateway online, but PLC is not online ^{CODESYS Forge talk (Post)}
we need some logfiles from the edge gateway /etc/Gateway.cfg [CmpLog] CmpEdgeGateway.Filter=0xFFFFFFFF Logger.0.Name=/tmp/codesysedge.log Logger.0.Filter=0x0000000F Logger.0.Enable=1 Logger.0.MaxEntries=100000 Logger.0.MaxFileSize=5000000 Logger.0.MaxFiles=1 Logger.0.Backend.0.ClassId=0x00000104 ;writes logger messages in a file Logger.0.Type=0x314 ;Set the timestamp to RTC and does the scan via Automation Server show the plc?
Last updated: 2024-01-09

Post by felipemsgarcia on Edge Gateway online, but PLC is not online ^{CODESYS Forge talk (Post)}
Hello, I couldn't figure what/where the issue was, so I deleted everything from automation server and reinstalled the edge gateway and did the process again. It worked for about a month and then it stopped working again. It presents the same symptom, edge gateway is online but I can't connect to the PLC. Any idea of what could be the issue? Thank you!
Last updated: 2024-01-09

Post by felipemsgarcia on Edge Gateway online, but PLC is not online ^{CODESYS Forge talk (Post)}
Hi Edwin, The PLC is already in the automation server so nothing happens when I scan the network, however the PLC show offline (not connected). Please see logs below. [CmpLog] Logger.0.Name=codesysedge.log Logger.0.Filter=0x0000000F Logger.0.Enable=1 Logger.0.MaxEntries=100000 Logger.0.MaxFileSize=1000000 Logger.0.MaxFiles=1 Logger.0.Backend.0.ClassId=0x00000104 ;writes logger messages in a file Logger.0.Type=0x314 ;Set the timestamp to RTC Thank you!
Last updated: 2024-01-09

Post by sturmghost on Visualization using methods and cyclic ST-calls ^{CODESYS Forge talk (Post)}
I found a way to do it: You can use, for example, the text variable property of any visualization element and call a function in it. Example: Write a test POU as a function (FUN), like MyTestFun which need a boolean Variable as an input value. Now write into the text variable property: MyTestFun(bBooleanValue) Thats it. The function is called at each visu_task cycle.
Last updated: 2024-01-22

Post by wiresplus on Cannot get INT_TO_TIME working ^{CODESYS Forge talk (Post)}
Hello, I have a simple TON timer. It is watching prime loss for a pump. The operator can set the delay via the HMI, it is an integer (seconds) As the TON uses milliseconds, we then multiply the entry by 1000 to get seconds. Seems simple, but... VAR PrimeTimer : TON; primetime : INT; END_VAR PrimeTimer(in:=State>0 AND FlowRate<MinimumFlow,pt:=INT_TO_TIME(primetime *1000)); For an entered 15 seconds (VAR primetime:=15;) the timer reads 49d17h2m26s760ms !!!! What am I doing wrong?
Last updated: 2024-01-26

Post by thomas-moba on "sudo"-Befehle über die Funktion "SysProcessExecuteCommand2" ^{CODESYS Forge talk (Post)}
Hello, I need to execute "sudo" commands via CoDeSys 3.5 SP 19 P5 using the "SysProcessExecuteCommand2" function. Commands without sudo are no problem, but as soon as sudo is used in a .sh or a single command, it does not work. Command=AllowAll is entered under "SysProcess" in CODESYSControl.cfg. Nevertheless it does not work. Does anyone know what the problem could be? Greetings, Thomas
Last updated: 2024-02-01

Post by matt-s on HMI Pushbutton/Move Instruction ^{CODESYS Forge talk (Post)}
I have not gotten to the bottom of this yet no. I have double check that the variables are correct linked. When online with the program I can see the button and rung going true for the move instruction, yet it does not change. Forcing the bit in the program does change the value in Groov View. I am kind of at a loss here, especially since the other POU(For the pumps) does the same thing fine.
Last updated: 2024-02-02

Post by tvm on VisuFbFrameBase.SetInputPositionData: The element id for the input position cannot be determined ^{CODESYS Forge talk (Post)}
I'm getting this error on one of my projects. Searching for it I came across this https://www.codesys.com/fileadmin/data/Images/System/Releaseinformation/Patch-Note-CODESYS-Visualization-4300.html which says it was a bug VIS-1394, fixed in Visualization 4.3.0.0. I'm using a previous visu version, what is the cause of this error, and what can be done to work around it?
Last updated: 2024-02-08

Post by goki on WAGO RS485 (753-652) on a 750-362 ^{CODESYS Forge talk (Post)}
hi guys Maybe someone can help me in this case. Im working with codesys 3.5 with an PFC200 (750-8212) with a Modbus TCP conection to the 750-362. On the 750-362 i have a 4DO, 8DI and a RS485 interface card. the 4DO and 8DI cards a working fine but im strugling with the rs485 card. Does someone have a example for this?
Last updated: 2024-02-08

Post by thomasrohnerch on Color Change for Symbols not working ^{CODESYS Forge talk (Post)}
I have some Symbols from the Visualization Toolbox on my Target Visu on the Computer. I tried many Symbols, mainly Arrows. I'm able to control the visibility with condition e.g. "GVL.actual_testvalues.speed <= 0" But I can't do "Toggle color" with boolean GVL.b_toggle_color. Neither "TRUE" nor "FALSE" does change anything. Is this a known issue? I'm using CODESYS V3.5 SP19 Patch 5 + (64-bit). See attached file with more Version-Info. I'm currently using Style 6, Gradient axial 2, 3.5.12.0. I had the same issue with Default 3.5.16.0.
Last updated: 2024-02-08

Sort by relevance or date