Post by aliazzz on Runtime licenses not detected => DEMO Mode 2hour ^{CODESYS Forge talk (Post)}
Hi! After upgrading all my licensed runtimes to V4.14.0.0 (= RaspberryPi SL, LinuxSL and ControlWin x64 SL) I found out via the logfiles they all defaulted back into DEMO mode while all runtimes have a USB dongle inserted. So, my main question is how I can get the Dongle license detected? I use License Server 4.14.0.0 and Edge Gateway 4.14.0.0 on all platforms Any suggestions are welcome.
Last updated: 2024-12-15

Post by bruno-roth on Read "Homed" status from EtherCAT drive ^{CODESYS Forge talk (Post)}
Hello, the information if your axis is already homed you could only find out direct from your Slave. In DS402 status there is no Bit defined. But some manufacturer of Drives use some optional bits or status. E.g. if you have Schneider Electric LXM32 Servo you will find this information in Bit 15. You have to check the manual of your used Servo-Drive f this information is provided in any object and then read it out with SDO.
Last updated: 2025-01-08

Post by teichhei on The selected container ... does not fit your ticket ^{CODESYS Forge talk (Post)}
Update, installed 3.5.19.70 with the same result. The error message is as useful as a chocolate fire guard. The container SN is in the 130-xxx range which should work. The Version, Chip, Rev number don't mean anything to me. There is no SD Card installed. I've also reinstalled a fresh Wago FW22 image, Deployed PFC200 SL and Edge for Linux, still the same result.
Last updated: 2025-01-09

Post by askic on PLC error log help ^{CODESYS Forge talk (Post)}
Hello, I'm using Codesys 3.5.20.0 version and I noticed that even with the most basic standard project create, there are error messages like shown in the acttached picture. The similar questions are already asked here on the CODESYS Forge Talk, but remained unanswered. Exact screenshot is attached, but essentially I would like to know which component in the Codesys has CmpID = 0x00000019 and what this Timeout means?
Last updated: 2025-01-10

Post by paulpotat on Can't find the safety manual in the documentation ^{CODESYS Forge talk (Post)}
Hello, I was browsing the "CODESYS Virtual Safe Control for Linux SL" documentation page, and it says the following : For more information about the development of safety-critical applications with CODESYS, see: * Safety Manual H1 – SafetyManual.pdf, which is stored in the directory ../<user>/CODESYS Virtual Safe Control Linux SL/Delivery/Manuals</user> What does this path refers to ? I can't find it in CODESYS installation directories. Best regards
Last updated: 2025-01-23

Post by andre-luis on Device diagnosis ( EtherCAT IO card ) ^{CODESYS Forge talk (Post)}
Hi @TimvH, In the meantime, I did some experiments and could find a way to achieve similar result. I made some tests, removing the last card from the array, seeing the change on status. PROGRAM P_IOS_STATUSES VAR devStateInput : DEVICE_STATE; devStateOutput : DEVICE_STATE; devStateEncoder : DEVICE_STATE; END_VAR devStateInput := IoConfig_Globals.EL1819.GetDeviceState(); devStateOutput := IoConfig_Globals.EL2809.GetDeviceState(); devStateEncoder := IoConfig_Globals.EL5151.GetDeviceState(); GVL.bInputCardOK := ( devStateInput = DEVICE_STATE.RUNNING ); GVL.bOutputCardOK := ( devStateOutput = DEVICE_STATE.RUNNING ); GVL.bEncoderCardOK := ( devStateEncoder = DEVICE_STATE.RUNNING ); Many thanks for your quick and extensive reply.
Last updated: 2025-02-06

Post by timvh on Codesys Runtime Devie Password ^{CODESYS Forge talk (Post)}
This has been moved because of security reasons. But it depends on how you start CODESYS where the project files are located (at least for Control Win from SP20). 1) If you start it through the sys tray icon, you start it as a service and the files will be located in: C:\Windows*System32\config\systemprofile\AppData\Roaming\CODESYS... (or C:\Windows*SysWOW64**\config...) 2) If you start it as a user, e.g. with a shortcut to the runtime, you can find it in: C:\Users\<your user="" name="">\AppData\Roaming\CODESYS...</your>
Last updated: 2025-02-11

Post by rmaas on TCP Server ^{CODESYS Forge talk (Post)}
Hi George, I do not know what the problem is with the syssocket implementation, but when i read the forums it seems the Net Base Services library is the recommended way to go. There is another more extensive example here: https://forge.codesys.com/prj/codesys-example/plc-chat-nbs/home/Home/ I have just tested this example and it works very well, also with closing and opening the connection from hercules... good luck!
Last updated: 2025-02-20

Post by pernockham on Inheritence of struct, ^{CODESYS Forge talk (Post)}
Interesting, thanks! Didnt know about ANY before, and will sure find a use-case for it. Im not sure it will help me here though, it seems to me that an ANY will not accept a string assignment? I actually think that the "ALIAS" should work, that was a hard found error. I had a fair bit of scratching my head looking for misdirected pointers before I understood what was (not) happening. I will use the work-around of individual structs instead.
Last updated: 2025-03-08

Post by patrik on windows runtime crashes. ^{CODESYS Forge talk (Post)}
Faulting application name: CODESYSControlService.exe, version: 3.5.20.30, time stamp: 0x66ebc91d Faulting module name: unknown, version: 0.0.0.0, time stamp: 0x00000000 Exception code: 0xc0000005 Fault offset: 0x0000028010670e31 Faulting process id: 0x0x1F50 Faulting application start time: 0x0x1DB1BA284347B9C Faulting application path: C:\Program Files\CODESYS 3.5.20.30\GatewayPLC\CODESYSControlService.exe Faulting module path: unknown Report Id: d3ac6a03-667a-4d61-ab36-d2ae703fc252 Faulting package full name: Faulting package-relative application ID: My runtime crashes from time to time. I'm not getting anything in the PLC logs. This is from the windows logs. Can anyone help me understand why this is happening?
Last updated: 2025-03-19

Post by lamine97 on Issue with Timer-Based Increment Function in CoDeSys Ladder Logic (LD) ^{CODESYS Forge talk (Post)}
I am trying to implement a Ladder Logic (LD) function block in CoDeSys that increments a value A by B every T time interval. My Structured Text (ST) version works perfectly in simulation, but when I implement it in LD, it does not work. The ST code: PROGRAM ADDITION VAR_INPUT A : LREAL ; B : LREAL ; T : TIME ; END_VAR VAR Timer : TON ; END_VAR Timer (IN:=TRUE, PT := T); IF Timer.Q THEN A := A + B ; Timer(IN := FALSE ) ; END_IF;
Last updated: 2025-03-25

Post by kuegerls on OpC UA server on Raspberry Pi MC SL - Certificate Issue ^{CODESYS Forge talk (Post)}
Hello, I have set up an OPC UA server following several guides, including this one: https://revolutionpi.com/documentation/tutorials/opc-ua-codesys-nodered/. The license for the runtime is installed on the device. However, I am unable to create a certificate for the OPC UA server in the security screen. I always get the error message: "The certificate has not been created by the device." Does anyone have an idea what might be causing this issue? Any help would be greatly appreciated! Thanks in advance! Best regards, Stefan
Last updated: 2025-04-02

Post by installwhat on Ethercat and profinet on together ^{CODESYS Forge talk (Post)}
I'm curious about the impact of having profinet and Ethercat (specifically softmotion so frame at start of task?) running together. Since it's advised to access the data from the bus task should have both profinet io and ethercat on the same task? Are there any implications around this one should be aware of especially since the frame at task start is just, so far as I'm aware, an ethercat thing? Thanks
Last updated: 2025-04-08

Post by imdatatas on Import from XML problem ^{CODESYS Forge talk (Post)}
Hello Everyone, When I try to import some POUs that were previously exported from another project as an XML file, I get an error like in attached image and the process does not complete. "There are no objects in the export file..." I am using SP21 Codesys IDE and I do not know which version this XML (*.export) file was previously exported with. Has anyone encountered the same problem? Regards, imdatatas
Last updated: 2025-04-26

Post by wbj0t on Update project from SP20 to SP21 ^{CODESYS Forge talk (Post)}
Hello everyone. I have a problem: I installed new version of codesys IDE. When I try open project in this new version, I have many errors about Visu: rectalnge/button/frame/etc does not exist. How update properly project? 20+ pages of visu pages from 100+ frames and all visu elems looks like "Error image". It is not problem of SP20->SP21. Any update has problems from visu side.
Last updated: 2025-06-09

Post by josul on Web Client HTTPS Communication Issue ^{CODESYS Forge talk (Post)}
Thank you for the suggestion. There is a certificate created in the quarantine directory relating to the URL used for the webclient FB. This certificate should have been valid as it was created only the week before this problem was encountered. I investigated a separate location using the same https URL and it has 2 certificates in the same quarantine directory, 1 is created almost 200 days ago, the other over 100 days ago. There have been no similar problems encountered with these certs or https at all.
Last updated: 2025-06-09

Post by berkdan on SMC_ReadNCFile2 is always busy ^{CODESYS Forge talk (Post)}
Hey tk96 Thank you for your help. I have found the reason why fbreader stuck. It was not the program but it was the gcode itself. G21 command blocks the reader. And multiple G codes in a line also blocks the reader. My code was: N010 G21 G17 G90 -> Blocked the reader When i change it to: N010 G90 N020 G17 Then it worked. The only thing i did not get is why the reader did not thwor error. ErrorId was SMC_NO_ERROR. Anyway, it is now working. Thanks again.
Last updated: 2025-06-17

Post by nguyenkhoi on Omron R88D-KN08H-ETC with a raspberry on top... (over ethercat) ^{CODESYS Forge talk (Post)}
hi everyone, continuing the part about omron g5 axis and nx-ecc201 omron, but i have a problem with not being able to scan with "model with Z code suffix of omron china", it seems that the available softmotion file is not fully compatible mapping, often causing ethercat communication error DC distributed clock after every 10-12 hours of continuous running! omron driver: R88D-KN08H-ECT-Z
Last updated: 2025-07-01

Post by jari-koivuluoma on Finding out exception code position ^{CODESYS Forge talk (Post)}
Is it possible to find out the code position from where the exception originated using information from this log entry? 2025-07-02T13:56:19Z, 0x00000011, 8, 81, 3, #### Exception: *EXCEPTION* [<excpt>AccessViolation</excpt>] occurred: App=[<app>Application</app>], Task=[<task>Task</task>] 2025-07-02T13:56:19Z, 0x00000011, 8, 81, 3, #### Exception: *SOURCEPOSITION* App=[<app>Application</app>] area=<area>2</area>, offset=<off>13349868</off>
Last updated: 2025-07-02

Post by adamrobotic on llcallback() iec exception caught cmpid=0x00000002, eventid=0x00010008 ^{CODESYS Forge talk (Post)}
Hi All, Recently I have been experiencing a issue in CodeSys SP16 Patch 3, with a exception which comes up after I have made several online changes. callcallback() iec exception caught cmpid=0x00000002, eventid=0x00010008, after I experience this fault then I receive a error message for any subsequent online change "online change failed, no task gap within 10000ms". To recover either the controller needs a orgin reset, which will allow online edits thereafter until falling back into the loop. I am using a TURCK TX707 product which is controlling robot trajectory, We have hard coded the coordinate data rather than using persistence variables so hence the need to do online changes consistently. I have read on the forum other people have experienced similar issue with the online task gap, but I have no task which have same priority and also monitored the CPU usage and have not seen it go above 13%. Anyones help would be much appreciated, thankyou.
Last updated: 2023-08-18

Post by timvh on Detect "Cancel" Press in FileOpenSave Dialog ^{CODESYS Forge talk (Post)}
Maybe there is a better way, but a long time ago I created a test application that worked like this: With a button I opened the dialog and I added a "Input configuration - OnDialogClosed" "Execute ST-Code" action to this same button which called the following Function when the dialog was closed: F_OnFileDialogClosed(pClientData); Below this Function which handled the result: // This function is called from the visualization when the dialog is closed. FUNCTION F_OnFileDialogClosed : BOOL VAR_INPUT pClientData : POINTER TO VisuElems.VisuStructClientData; END_VAR VAR dialogMan : VisuElems.IDialogManager; FileOpenCloseDialog : VisuElems.IVisualisationDialog; result : VisuElems.Visu_DialogResult; _sFileName : STRING(255); END_VAR // the DialogManager is provided via the implicitly available VisuManager dialogMan := VisuElems.g_VisuManager.GetDialogManager(); IF dialogMan <> 0 AND pClientData <> 0 THEN FileOpenCloseDialog := dialogMan.GetDialog('VisuDialogs.FileOpenSave'); // gets the FileOpenSave dialog IF FileOpenCloseDialog <> 0 THEN result := FileOpenCloseDialog.GetResult(); // gets the result (OK, Cancel) of the dialog IF result = VisuElems.Visu_DialogResult.OK THEN // Original code gvlFile.FileListProvider(); _sFileName := CONCAT(gvlFile.FileListProvider._stDirectory, gvlFile.FileListProvider.stFile); // do something with this file name... END_IF END_IF END_IF
Last updated: 2023-09-19

Post by ewi04 on Git with visu ^{CODESYS Forge talk (Post)}
Hi, I have several problems with the git extension. Situation: I am working with Codesys v3.5 SP19 Patch 1 and Git V1.2.1.0. The remote repository is GitLab Community Edition v16.1.2. I am working on a project with one other person. Problems: 1: After each start of Codesys all of the visu pages are marked as modified. So we have to discard all changes first. Otherwise the history is not clean and the merge request becomes more complex. I tested it with a new project and only local. I made the observation, that a page is not marked as modified when it is committed a second time (after a restart of codesys). But this is necessary after every change of a page. However, since we are working in a team, it seems we are playing ping-pong and so all pages are marked as modified on each startup. 2: Each image pool causes a parent child conflict. Also in my local project. The only solution that I have found, is to ignore the issue. Does anyone have the same problems? I think it looks more like bugs. Thanks ewi04
Last updated: 2023-11-22

Post by ph0010421 on How to create a stopwatch? ^{CODESYS Forge talk (Post)}
Do you need an 'hours-run' counter? And 1 second resolution is ok? I think you're over-thinking it. (The task time needs to be < 1second) Have a look at the LAD... Then, the time in seconds can be made into hh:mm:ss with this FUNction Declarations: FUNCTION funSecondsToStringTime: string VAR_INPUT InSeconds: UDINT; END_VAR VAR AsString: STRING; Minutes: UDINT; Hours: UDINT; Seconds: UDINT; MinutesAsString: STRING(2); HoursAsString: STRING(2); SecondsAsString: STRING(2); END_VAR and the code: Hours := InSeconds / 60 / 60; //Derive hours Minutes := (InSeconds - (Hours * 60 * 60)) / 60; //Derive minutes Seconds := InSeconds - ((Hours * 60 * 60) + (Minutes * 60));//Derive seconds HoursAsString := UDINT_TO_STRING(Hours); MinutesAsString := UDINT_TO_STRING(Minutes); SecondsAsString := UDINT_TO_STRING(Seconds); IF LEN(HoursAsString) = 1 THEN HoursAsString := CONCAT('0',HoursAsString); END_IF; IF LEN(MinutesAsString) = 1 THEN MinutesAsString := CONCAT('0',MinutesAsString); END_IF; IF LEN(SecondsAsString) = 1 THEN SecondsAsString := CONCAT('0',SecondsAsString); END_IF; AsString := CONCAT(HoursAsString, ':'); //assemble string AsString := CONCAT(AsString,MinutesAsString); AsString := CONCAT(AsString,':'); AsString := CONCAT(AsString, SecondsAsString); funSecondsToStringTime := AsString;
Last updated: 2023-12-08

Post by aseitzinger on CODESYS Control for Linux SL on virtual machine? ^{CODESYS Forge talk (Post)}
Hello, there in different information available regarding the possibility to run CODESYS Control for Linux SL on a virtual machine. https://forge.codesys.com/trg/linux-sl/home/Home/ says CODESYS Control for Linux SL is a runtime system, which can run on any Debian based X86 PC, VM or Cloud container... https://store.codesys.com/media/n98_media_assets/files/2302000005/3/CODESYS%20Control%20for%20Linux%20SL_de.pdf says CODESYS Control for Linux SL can not be used on virtual hardware Currently I run the package mentioned on a virtualized debian machine running in PROXMOX Virtual Environment 7.4-17 and apart from huge jitter it runs without problems. The CODESYS key is passed as a USB defice to the VM. I wonder why there are different statements regarding the suitability in virtual machines and if the jitter would be reduced by installing CODESYS runtime on the host installing CDS runtime on the host and using a preemptive kernel (if available for the PROXMOX installation leaving CDS runtime where it is (on the virtualized debian machine) and install a preemptive kernel on the host and on the guest... Any advice is appreciated. Greets Arno
Last updated: 2024-01-08

Post by anlebr on Codesys Communication Manger - Required information model version exists in the model repository but is not found ^{CODESYS Forge talk (Post)}
Hi I am trying use the Codesys Communication Manager to set up an Opc ua server with a custom information model. As a start I am using the Boiler model available on Opc foundations github page. I am testing with a Wago CC100 and using Codesys V3.5 SP19 Patch 6. I get the following error: Communication Manager [Device: PLC Logic: Application]: The information model http://opcfoundation.org/UA/ is required by http://opcfoundation.org/UA/Boiler/ with a minimal publication date from 15/12/2023 but the device has only a model from 15/09/2021 installed. Probably the information model from 15/09/2021 is missing in the information model repository. The error message does not make sense to me. Should it not be “Probably the information model from 15/12/2023 is missing in the information model repository”? Anyway, both versions are available in the repository. How can I solve this?
Last updated: 2024-03-13

Sort by relevance or date