Post by olehmann03 on PFC200 - WAGO 750-8202 - MODBUS RTU ^{CODESYS Forge talk (Post)}
Hello, I’m working on implementing Modbus RTU communication with a Carel controller (CPCO). I want to use the front RS485 interface through the DB9 connector. The issue is that I can’t get the communication working correctly. Below are the steps I’ve done so far: Connected pins 3 and 8 from the DB9 connector to the +/- RX/TX terminals on the Carel side. In the PLC shell, I set serialmode to RS485. In WBM under Administration > Serial Interface > Assign owner of serial interface, I set the port to unassigned. In the device tree, I created Modbus_COM with the following settings: COM port: 1 Baud rate: 19200 Parity: None Stop bits: 1 Created a Modbus client on this COM interface in RTU mode. Under the status tab, I can see it is in running state. On the client, I created a Modbus server and set the Modbus address of my unit to 1. Defined a few channels as FC03 to read holding registers according to the Carel register map. I checked the communication with the Carel controller using a USB-to-RS485 converter connected to my PC, and communication works correctly there. In the status tab, I can see that the Modbus server is polling, but there is no response from the controller. I also tried multiple times swapping A/B lines on the Carel side, but it did not help. Do you have any suggestions on what else I should check?
Last updated: 2026-05-22

Post by olehmann03 on PFC200 - WAGO 750-8202 - MODBUS RTU ^{CODESYS Forge talk (Post)}
Hello, I’m working on implementing Modbus RTU communication with a Carel controller (CPCO). I want to use the front RS485 interface through the DB9 connector. The issue is that I can’t get the communication working correctly. Below are the steps I’ve done so far: Connected pins 3 and 8 from the DB9 connector to the +/- RX/TX terminals on the Carel side. In the PLC shell, I set serialmode to RS485. In WBM under Administration > Serial Interface > Assign owner of serial interface, I set the port to unassigned. In the device tree, I created Modbus_COM with the following settings: COM port: 1 Baud rate: 19200 Parity: None Stop bits: 1 Created a Modbus client on this COM interface in RTU mode. Under the status tab, I can see it is in running state. On the client, I created a Modbus server and set the Modbus address of my unit to 1. Defined a few channels as FC03 to read holding registers according to the Carel register map. I checked the communication with the Carel controller using a USB-to-RS485 converter connected to my PC, and communication works correctly there. In the status tab, I can see that the Modbus server is polling, but there is no response from the controller. I also tried multiple times swapping A/B lines on the Carel side, but it did not help. Do you have any suggestions on what else I should check?
Last updated: 2026-05-22

Post by marekxc on Error C0521 - unknow compiler ^{CODESYS Forge talk (Post)}
Select in tree "DEVICE", right-click and select "Update Device" Select "Library manager" and Change the version of the Library (down manualy). Samoetimes "Try reload Library". If you open a project version 3.5.19 in version 3.5.16, there are difficulties.
Last updated: 2023-09-02

Post by nyee on Project compiling error in Simulation mode ^{CODESYS Forge talk (Post)}
Hi, I have a similar issue - we have been using codesys V3.5.16.20 Do you have any suggestions or confirmation that this will work with a different version of codesys and Pi extension
Last updated: 2023-09-07

Post by necatibilgin on Communication betwee 2 codesys devices with PROFINET ^{CODESYS Forge talk (Post)}
Hi everybody, Is there any sample project that communicates 2 devices with profinet using Codesys platform on the devices? BR, Necati.
Last updated: 2023-11-03

Post by baldeep on Codesys Raspberry Runtime 4.10.0.0 and RSM Utility 3.5.19.0 ^{CODESYS Forge talk (Post)}
I had been using Codesys Raspberry 4.9.0.0 Runtime for a Project with CAA File 3.5.19.0. But now with Update 4.10.0.0 and Raspberry pi 64 Bit.....i cannot compile my code as RSM Utility 3.5.19.0 is not recognised. Any help? Regards
Last updated: 2023-11-20

Post by jeroenaero on CodeSys Raspberry pi I2C driver not found ^{CODESYS Forge talk (Post)}
I tested your project but with same results i am still not seeing analog values. I also included the library list, the mainprogram.
Last updated: 2024-11-08

Post by s1ack on Undertanding Application Based Licenses ^{CODESYS Forge talk (Post)}
Can anyone confirm my thinking here that this project will require Control Standard M because of the I/O channel count under the fieldbus?
Last updated: 2024-11-08

Post by simone on Collapse all ^{CODESYS Forge talk (Post)}
Thank you so much r-niedermayer, it really helps me. Sorry for the late response but I have worked on a different project rather than the codesys one
Last updated: 2024-12-03

Post by rmaas on TCP Server ^{CODESYS Forge talk (Post)}
Hi George, I am no expert but recently tried and got it working using this example project: https://forge.codesys.com/prj/codesys-example/nbs/home/Home/#example-for-tcp-server-tcp-client BR, Rinie
Last updated: 2025-02-20

Post by fil on Using Latch Variable in Alarm as input from text list ^{CODESYS Forge talk (Post)}
Good morning, I am currently working on a project where this would be of enormous value. Any input would be very welcome - thanks in advance. Best regards Fil
Last updated: 2025-03-06

Post by bernardchen on Modbustcp.lib missing codesys v2.3 ^{CODESYS Forge talk (Post)}
a codesys project V2.3.9 opened with error of libuary missing. Modbustcp.lib and Modbustcpsrv.lib where can I download these two libs . I am a beginner of codesys. this codesys v2.3 is running in virtualbox XP system without internet access.
Last updated: 2025-03-12

Post by programmer on 3.5 P20 hangs - no response ^{CODESYS Forge talk (Post)}
Hi, Is there a solution found for the problem described in first post? Any version above Codesys 3.5 P19 hangs during start up. It makes no difference whether I simply start Codesys or open a project directly. I'm using Windows 10 Home edition. Thanks!
Last updated: 2025-06-23

Post by gseidel on MC_MoveAbsolute: C0138: No matching 'FB_Init' method found for instantiation of SMC_MoveAbsRelPerformerImpl [ERROR] ^{CODESYS Forge talk (Post)}
Hi Imdat, can you please provide the exact version of CODESYS and the compiler version in the project settings? Thanks, Georg
Last updated: 2025-09-08

Post by pernockham on PHOENIX CONTACT Axioline PLCnext project in CodeSys SodftPLC ^{CODESYS Forge talk (Post)}
The structure should be the same independent of which runtime version. Im using Codesys control for linux SL. Ie, add an ethernet device, then profinet controler then phoenix PN bus coupler.
Last updated: 2025-09-09

Post by ranadheer on PHOENIX CONTACT Axioline PLCnext project in CodeSys SodftPLC ^{CODESYS Forge talk (Post)}
Thankyou TimvH ,while searching in every device about the component it is same like above screenshot,and i crosscheck with the device repository but devices are available here.
Last updated: 2025-09-09

Post by pernockham on PHOENIX CONTACT Axioline PLCnext project in CodeSys SodftPLC ^{CODESYS Forge talk (Post)}
You should use PLCnext if your device-hw is a PLCnext-un it. As I understand it you are using "CODESYS Control Win V3 x64".
Last updated: 2025-09-09

Post by liai on can not new a cam table in codesys V3.5 SP20 ^{CODESYS Forge talk (Post)}
I am using a new project, with nothing, but when add a simple cam table, and compile, there will be errors. It seems some add-on or library was missing, but there is not any hint. Could you help, please.
Last updated: 2025-09-18

Post by lipton on Safety Cross-communication with network variables ^{CODESYS Forge talk (Post)}
I am currently engaged in research for a Codesys project that involves the establishment of communication between two or more Codesys safety controllers using safe communication protocols, would it be possibole ? /Best Regards
Last updated: 2023-12-29

Post by yann2021 on SysProcessExecuteCommand ^{CODESYS Forge talk (Post)}
Hello, I have this code who worked fine in an other project with a previous SP. Why do I have now errors when I generate this code...? Who can help me pls? Many thanks for your help.
Last updated: 2024-02-04

Post by thewizard8 on Raspberry PI4 Serial Port ^{CODESYS Forge talk (Post)}
Hi eschwellinger, Thanks for replying, but I'm not shure if I got it right. Do you mean that I have bad configuration on my CODESYS config file? Or in my project? Thanks in advance!
Last updated: 2024-03-19

Post by vincentger on v3.5 SP19 - Modbus TCP Devices - Channel Limit? ^{CODESYS Forge talk (Post)}
Any resolution on this? I have currently 75 channels in my project that i brought up from SP18, which means i am 65 Channels above the new limitation?
Last updated: 2024-04-09

Post by gseidel on CNC / G01 Speed is very slow (or go-stop motion) in Continuous short segment . ^{CODESYS Forge talk (Post)}
Hi k2saki, 1.SMC_ReadNCFile2 2.SMC_Interpreter 3.SMC_SmoothMerge 4.SMC_SmoothPath 5.SMC_CheckVelocities I attached a simple example project. Best regards, Georg
Last updated: 2024-04-30

Post by gseidel on Warning C0564 when compiling CNC project with variables program ^{CODESYS Forge talk (Post)}
Hi Fless, thanks for your report! We created an issue in our bug tracker (SM-5109) and will have a look at this issue. Best regards, Georg
Last updated: 2024-04-30

Post by rabaggett on CODESYS control for Raspberry Pi 64 SL errors ^{CODESYS Forge talk (Post)}
It is either my installation is bad, or there is a bug. I re-created the project in 3.5 SP19 and there are no errors or warnings. Compiles with no errors or warnings. The original was done in 3.5 SP20. Thoughts?
Last updated: 2024-05-03

Sort by relevance or date