Post by andrax on Meine Gerätesammlung basierend auf TCA9548 ^{CODESYS Forge talk (Post)}
Hallo zusammen, ich programmiere öfters mal kleinere Messgeräte und Datenlogger. Je nach Einsatzzweck musste ich mir ein paar Gerätetreiber selber schreiben. Da es eine recht große Sammlung ist, stelle ich die hier einfach mal ein. Die Sammlung basiert auf den Gerätetreiber TCA9548 Multiplexer von Steffen Dreyer. Codesysversion: V3.5 SP18 Patch 4 Inhalt: -4channel Dimmer (Stefan Dreyer) -BMA456 (Andre Klien) -BME280 (Stefan Dreyer) -BMP280 (Stefan Dreyer) -EEPROM_24C512 (Stefan Dreyer) -ADS1115 (Andre Klien) -ICP10125 (Andre Klien) -PCA9555 (Stefan Dreyer) -PCA9685 (Stefan Dreyer) -PCF8575 (Stefan Dreyer) -SDP810 (Andre klien) -SSD1306 (Stefan Dreyer) -TCA9548 (Stefan Dreyer) -TSL2561 (Stefan Dreyer) Alle Gerätetreiber laufen über den Multiplexer, können aber auch ohne betrieben werden. Einschränkung: BMA456: Die Konfigurationsdaten werden erfolgreich in den Chip geschrieben, dieser meldet aber config wrong. Warum auch immer, der Sensor funktioniert und bringt hochempfindlich Beschleunigungsdaten. ADS1115: Hie habe ich nur die wichtigsten funktionen implementiert. 1-4 Kanäle, PGA, kontinuierlicher Modus, Datenrate. Alle anderen Funktionen (single-shot, komparator,alm) sind nicht implementiert. Das macht auch keinen Sinn, da diese Funktionen besser über die Steuerung realisiert werden können. Achtung beim ADS1115 ist zwingend ein Levelshifter notwendig, wenn ihr diesen mit 5V betreiben wollt. Ihr grillt sonst euren Raspi (SDA, SCL sind dann 5V) Gruß Andre
Last updated: 2023-12-18

Post by dhumphries on Minimum system requirements for codesys control standard S ^{CODESYS Forge talk (Post)}
I'm working on a low cost project and I'm considering installing the Codesys runtime on a PC running Linux Debian instead of buying a PLC with a pre-installed runtime. For my needs the Control Standard S license should be capable of running some IO over ethernet/ip, and a webvisu. The PC I am considering has a AMD GX-424CC 2.4GHz processor (4 core/4 thread) and 4GB RAM. This may compare to a raspberry pi4, but I know an X86 processor doesn't directly compare to an ARM processor, and a processor can have a high clock speed but other factors like L2/L3 cache can influence the overall performance. I can't find any published specs for the processor and RAM requirements to run the Codesys Control runtime, does anybody have a link to the minimum system requirements or experience using devices that are at or below the minimum system requirements. A raspberry pi with the control for raspberry pi SL runtime license would be the lowest cost option, but the license is not for commerical use. This restriction is somewhat vague, can anybody clarify if this means I can use a raspberry Pi runtime for in-house automation, what about if I am selling an integrated system that uses a raspberry Pi as a controller?
Last updated: 2023-12-25

Post by zoronoa on J1939.ReceiveWatchdog & J1939.ReceiveParameterGroup ^{CODESYS Forge talk (Post)}
Hi, I'm trying to monitor a specific PGN which I have it sending a pulse every 500mS Problem: Using the Watchdog for the ECU does not really help me as I have multiple instances with separate PGNs, if a PGN goes ghost, the ECU watchdog won't be flagged as the others will be running. I found the J1939.ReceiveWatchdog & J1939.ReceiveParameterGroup function blocks and they seem like a good solution for my problem, I just can't get them to work from my understanding you just build the J1939.ReceiveParameterGroup once and then connect it's output to the J1939.ReceiveWatchdog, here's my CODE for the setup HEARTBEAT_TIMER(IN:= TRUE, PT:= T#1000MS); //turn-on delay because of initialization race IF HEARTBEAT_TIMER.Q= TRUE THEN Glob_Var.DisplayReceive.xExecute:= TRUE; Glob_Var.DisplayReceive.itfECU:= Valve_X; Glob_Var.DisplayReceive.dwPGN:= 65511; Glob_Var.DisplayWatchdog.xEnable:= TRUE; Glob_Var.DisplayWatchdog.itfParameterGroup:= Glob_Var.DisplayReceive.itfParameterGroup; Glob_Var.DisplayWatchdog.tTimeout:= T#1500MS; END_IF Notes: Glob_Var.DisplayReceive is of type J1939.ReceiveParameterGroup Glob_Var.DisplayWatchdog is of type J1939.ReceiveWatchdog The above code is done once and not cyclically I'm monitoring Glob_Var.DisplayWatchdog.xError cyclically
Last updated: 2024-03-13

Post by alexgooi on Modbus writing on value change ^{CODESYS Forge talk (Post)}
Hi Duvan, You could make this in 1 single object (FB), Indeed don't use a function for this beacuse you need some memory to keep the old value. For i := 0 TO 200 BY 1 DO //Check if the value has been changed IF Old_Value[i] <> Value[i] THEN //Set the trigger to TRUE Trigger[i] := TRUE; Old_Value[i] := Value[i]; END_IF END_FOR If you define the Value array as an In_Out and the Trigger as an In_Out you arn't claiming any aditional memory to your system. You ofcourse then need to add some code arround it that does something with the trigger and writes it back to FALSE again. If you want more flexability you also could use pointers instead of using the IN_OUT FOR i := 0 TO 200 BY 1 DO address := address_Input + i * SIZEOF(*Put type here); IF Address^ <> Old_Value[i] THEN Trigger[i] := TRUE; Old_Value[i] := Address^; END_IF END_FOR
Last updated: 2024-04-02

Post by tim-roelant on Problem mit control runtime V3 und profinet ^{CODESYS Forge talk (Post)}
Hallo Edwin, meinst du das der control-win nicht wie SPS verwendet werden kann? Das program ist klein, und realtime brauch ich gar nicht, Es gibt im bus einem Turck inselstation mit 16 ein und ausgange, und ein MTS linearencoder, womit wir teile messen und abschneiden. Die cycluszeit reist auch nicht aus. Processorleisung bleibt unter 20%. Es geht mir darum das der profinet master in fehler geht, und nicht mehr seine telnehmer erkannen kann. Es kan passieren nach 10 minuten, aber auch nach 5 tage. Nur ein kaltstart bringt die bus wieder am laufen. (kein reconnect mochlich, auch die bus scannen functioniert nicht mehr) Wann ich aber ein ipscan durchfure mit Angryip auf der rechner sind alle telnehmer da. Ich habe noch eine andere application mit die gleiche anwendung, aber wo ein raspberry pi die SPS rolle spielt, und das functioniert einwandfrei. Soll ich fielleicht das OS von Rechenr nach linux umrusten? Der operator ist im moment sehr unzufrieden mit die "upgrade" von maschine... :-( lg Tim
Last updated: 2024-04-11

Post by tim-roelant on Problem mit control runtime V3 und profinet ^{CODESYS Forge talk (Post)}
Hallo Edwin, meinst du das der control-win nicht wie SPS verwendet werden kann? Das program ist klein, und realtime brauch ich gar nicht, Es gibt im bus einem Turck inselstation mit 16 ein und ausgange, und ein MTS linearencoder, womit wir teile messen und abschneiden. Die cycluszeit reist auch nicht aus. Processorleisung bleibt unter 20%. Es geht mir darum das der profinet master in fehler geht, und nicht mehr seine telnehmer erkannen kann. Es kan passieren nach 10 minuten, aber auch nach 5 tage. Nur ein kaltstart bringt die bus wieder am laufen. (kein reconnect mochlich, auch die bus scannen functioniert nicht mehr) Wann ich aber ein ipscan durchfure mit Angryip auf der rechner sind alle telnehmer da. Ich habe noch eine andere application mit die gleiche anwendung, aber wo ein raspberry pi die SPS rolle spielt, und das functioniert einwandfrei. Soll ich fielleicht das OS von Rechenr nach linux umrusten? Der operator ist im moment sehr unzufrieden mit die "upgrade" von maschine... :-( lg Tim
Last updated: 2024-04-11

Post by jose-coro on Trouble installing codesys 64 3.5.19.0 ^{CODESYS Forge talk (Post)}
I tried to intalling codesys 64 3.5.19.0, during the installation process I get the following messages: "One or more problems have appeared with the current version profile. please consult with the supplier to solve the problem. -The plugin '{ee08241a-dd43-445a-b0a1-de9f717d92e0}(exactly 3.5.19.0)' is required for the current version profile but is not installed. The plug-in '{c7880c90-68c0-4cf8-a726-f0ee72b11f86}(exactly 3.5.19.0)' is required for the current version profile but is not installed. The add-on '{973a3934-1ec6-4770-83a4-59677803015a}(exactly 3.5.19.0)' is required for the current version profile but is not installed. It is recommended to terminate the application." Then the following message appears: "This package could not be installed: CODESYS Compatibility Package 3.5.17.20”. After that the instalation continue and the folling message appears: "It is possible that packages from this path could not be installed: C:\Users...\Appdata\Local\Temp{EFE2F~1}\Packages"
Last updated: 2024-04-23

Post by jose-coro on Trouble installing codesys 64 3.5.19.0 ^{CODESYS Forge talk (Post)}
I tried to intalling codesys 64 3.5.19.0, during the installation process I get the following messages: "One or more problems have appeared with the current version profile. please consult with the supplier to solve the problem. -The plugin '{ee08241a-dd43-445a-b0a1-de9f717d92e0}(exactly 3.5.19.0)' is required for the current version profile but is not installed. The plug-in '{c7880c90-68c0-4cf8-a726-f0ee72b11f86}(exactly 3.5.19.0)' is required for the current version profile but is not installed. The add-on '{973a3934-1ec6-4770-83a4-59677803015a}(exactly 3.5.19.0)' is required for the current version profile but is not installed. It is recommended to terminate the application." Then the following message appears: "This package could not be installed: CODESYS Compatibility Package 3.5.17.20”. After that the instalation continue and the folling message appears: "It is possible that packages from this path could not be installed: C:\Users...\Appdata\Local\Temp{EFE2F~1}\Packages"
Last updated: 2024-04-23

Post by mxj262 on FB having single input but initialized with Array ^{CODESYS Forge talk (Post)}
I am adding elements of an ARRAY using pointer to access each element inside a FOR loop and the FOR loop does not stop! What is the right way to use pointers in such case?? I have another loop that is not using pointer and it stops but the loop using pointer keep on adding. METHOD FB_Init: BOOL VAR_INPUT bInitRetains: BOOL; // TRUE: the retain variables are initialized (reset warm / reset cold) bInCopyCode: BOOL; // TRUE: the instance will be copied to the copy code afterward (online change) END_VAR VAR_IN_OUT // basically REFERENCE TO window_buffer: ARRAY [*] OF INT; // array of any size END_VAR THIS^.windowPtr := ADR(window_buffer[0]); THIS^.windowSize := UPPER_BOUND(window_buffer, 1) - LOWER_BOUND(window_buffer, 1) + 1; FUNCTION_BLOCK FB500 VAR_INPUT END_VAR VAR_OUTPUT END_VAR VAR windowPtr: POINTER TO INT; windowSize: DINT; currentIndex: UINT; element1:INT; element2:INT; i:INT; j:INT; sum:DINT:=0; END_VAR element1:=windowPtr[0]; // read the first element of the Array dynamic memorry element2:=windowPtr[1]; FOR i:=0 TO (TO_INT(windowSize-1)) BY 1 DO // this loop does not stop Sum:=sum + windowPtr[i]; END_FOR FOR j:=0 TO 5 BY 1 DO // this loop stops j:=j+1; END_FOR https://ibb.co/k3DhkZT
Last updated: 2024-05-06

Post by paro on Modbus Client Request Not Processed ^{CODESYS Forge talk (Post)}
Hi, Problem in your code is that you are not calling the ClientFb cyclic. Please look at the Example from CODESYS: https://forge.codesys.com/prj/codesys-example/modbus/home/Home/ Your code works if the client fb is called cyclic! IF NOT initDone THEN initDone := TRUE; // configure clientTcp clientTcp(aIPaddr:=Ethernet.IPAddress, uiPort:=502); // configure clientSerial clientSerial(iPort:=SysCom.SYS_COMPORT2, dwBaudRate:=SysCom.SYS_BR_115200, byDataBits:=8, eParity:=SysCom.SYS_EVENPARITY, eStopBits:=SysCom.SYS_ONESTOPBIT, eRtuAscii:=ModbusFB.RtuAscii.RTU); // configure clientRequestReadCoils_1 clientRequestReadCoils_1(rClient:=clientTcp, uiUnitId:=42, udiTimeout:=TO_UDINT(T#10MS)); // configure clientRequestWriteSingleRegister clientRequestWriteSingleRegister(rClient:=clientTcp, uiUnitId:=43, udiTimeout:=TO_UDINT(T#10MS)); // configure clientRequestReadCoils_2 clientRequestReadCoils_2(rClient:=clientTcp, uiUnitId:=44, udiTimeout:=TO_UDINT(T#10MS)); // configure clientRequestReadInputRegisters clientRequestReadInputRegisters(rClient:=clientTcp, uiUnitId:=44, udiTimeout:=TO_UDINT(T#10MS)); END_IF // call the client FB's clientTcp(); clientSerial(); // call client request FB's clientRequestReadCoils_1(rClient:=clientTcp, xExecute:=TRUE, uiStartItem:=2, uiQuantity:=3, pData:=ADR(aDataCoils_1[0])); // for more details see Example_TCP, especially ClientRequest control (xExecute, xDone, xError). IF clientRequestReadCoils_1.xDone THEN // get data from aDataCoils_1 ... END_IF clientRequestWriteSingleRegister(rClient:=clientTcp, xExecute:=TRUE, uiItem:=3, uiValue:=123); clientRequestReadCoils_2(rClient:=clientTcp, xExecute:=TRUE, uiStartItem:=2, uiQuantity:=3, pData:=ADR(aDataCoils_2[0])); clientRequestReadInputRegisters(rClient:=clientTcp, xExecute:=TRUE, uiStartItem:=16, uiQuantity:=3, pData:=ADR(aDataInputRegisters[0]));
Last updated: 2024-05-29

Post by caprez95 on Trace Restart Visuelement ^{CODESYS Forge talk (Post)}
Hallo zusammen. Ich habe schon länger mit dem Problem zu kämpfen, dass ich einen Trend (Visuelement) nicht resetten (neustarten) kann. Ich habe es jetzt mit dem Beispiel hinbekommen, die Trace-Aufzeichnung über die CmpTraceMgr Bibliothek zu steuern. Aber wie bekomme ich diese Trace-Aufzeichnung in ein Visuelement? Der Code sieht wie folgt aus: // Configure trace IF xInit THEN // Create a trace packet PacketConfig.pszName := ADR('IECTraceConfiguration.Trace1'); // Name of trace PacketConfig.pszApplicationName := ADR('IECTraceConfiguration'); // Name of the application PacketConfig.pszIecTaskName := ADR('Task'); // Name of the task PacketConfig.pszComment := ADR('Demo packet'); PacketConfig.ulEveryNCycles := 1; PacketConfig.ulBufferEntries := 1000; PacketConfig.ulFlags := TRACE_PACKET_FLAGS.TRACE_PACKET_FLAGS_TIMESTAMP_MS AND TRACE_PACKET_FLAGS.TRACE_PACKET_FLAGS_AUTOSTART; IF (NOT fbTraceManager.CreatePacket(PacketConfig := PacketConfig, hPacket=>hPacket1)) THEN xError := TRUE; END_IF // Create a trace record RecordConfig.pszVariable := ADR('iSignal'); // This is the name of variable to record RecordConfig.tcClass := INT_TO_UDINT(TypeClass.TYPE_INT); // Type of the recording variable RecordConfig.ulSize := SIZEOF(iSignal); // Size of the recording variable pApp := AppFindApplicationByName('IECTraceConfiguration', 0); AppGetAreaOffsetByAddress(pApp, ADR(iSignal), ADR(RecordConfig.tvaAddress.taAddress.Area.usArea), ADR(RecordConfig.tvaAddress.taAddress.Area.ulOffset)); // Get and set area offsets RecordConfig.tvaAddress.ulAddressFlags := TRACE_VAR_ADDRESS_FLAGS_IEC OR TRACE_VAR_ADDRESS_FLAGS_AREA_OFFSET; RecordConfig.ulGraphColor := 16#FF00FF00; // green RecordConfig.ulGraphType := 1; // Line with points IF (NOT fbTraceManager.AddRecord(RecordConfig := RecordConfig, hPacket := hPacket1, hRecord => hRecord1)) THEN xError := TRUE; END_IF xInit := FALSE; END_IF // Starts the recording IF xStart THEN IF (NOT fbTraceManager.StartPacket(hPacket := hPacket1)) THEN xError := TRUE; END_IF xStart := FALSE; END_IF // Stop the recording IF xStop THEN IF (NOT fbTraceManager.StopPacket(hPacket := hPacket1)) THEN xError := TRUE; END_IF xStop := FALSE; END_IF // Reset the recording IF xReset THEN IF (NOT fbTraceManager.ResetPacket(hPacket := hPacket1)) THEN xError := TRUE; END_IF xReset := FALSE; END_IF
Last updated: 2024-06-04

Post by xnoop on MBTCP Slave configuration ^{CODESYS Forge talk (Post)}
Hello, I use Codesys 3.5 SP18 Patch 4 (64 bit) My Codesys project is composed of several dozen of Modbus TCP Slaves. I want to configure each of them by define : - Modbus TCP Slave Configuration : Name, IPAddress, port - Channels - Mapping I can't afford to configure manually and I need to find automatic way What possibilities does the Codesys offer? 1. I know it possible to use python script to create Modbus TCP Master and Slave. But I don't find anyway to create Channels and Mapping through the API 2. I 've tested to set mapping with file.csv on a Modbus Tcp Slave, but no way to import channels definition from file 3. I 've tried to use PLCOpenXml file. For example I 've create a project with an Ethernet device. I've exported it in PlcOpenXml file. After delete the Ethernet device, I've imported the PlcOpenXml file without success. I've tried the same by creating Modbus TCP Slave. Could you help me to find to good way ? Thanks
Last updated: 2024-06-19

Post by kaotic2499 on Upgraded Raspberry 2b to Raspberry 5, Trends Broken? ^{CODESYS Forge talk (Post)}
Hello! Raspberry pi 2b just is getting a bit slow so decided to go for a Raspberry 5. Project is now upgraded to suit Pi 64 SL... so, now although everything runs perfectly... for some reason my trends will not save! its driving me nuts... ^Tried merging tasks with main program & trends ^tried re-prioritizing tasks (shifting 1 - 31 etc) ^Recreated the Trend Recording manager from scratch ^Tried swapping persisitant vars to GVL Retains then non-retains... (Project attached is as per before trial&error) Raspberry Pi 2b still runs "perfectly" though its very chuggy (Still saves the trends, note this is of an pretty much identical project minus the device compatibility) Does anyone have any advice to offer? project attached.... I feel it could be outside of Codesys itself causing the issues, but cant see/find anything on the internet to assist (or anyone else with the same problem as me...) Can attach project in another format (non archive) any assistance is much appreciated!
Last updated: 2025-10-19

Post by timvh on Toradex and CODESYS and licensing ^{CODESYS Forge talk (Post)}
For the Virtual Control you need to use a "Network license". The Virtual Control has parameters of which one is the reference to the license server. This can be the device itself, but you need to activate the license on the host system (not in the container). For this, CODESYS has a Network License server with WBM (web based management). See for the Network License configuration: https://content.helpme-codesys.com/en/CODESYS%20Control/_rtsl_license_controller_linux.html If it is only for evaluation, I would advise to use a CODESYS (USB) key and activate the license on the key. Then you still have to install the CODESYS Network License server on the host, but you don't have to activate the license as soft license on the device. The benefit is that you can easily move your license to another device when needed. Off course your device must have a free USB port available to be able to do this.
Last updated: 2025-10-20

Post by valenting on License problem with Raspberry Pi ^{CODESYS Forge talk (Post)}
Hello, I have a raspberry pi with a license installed, but Codesys stops after 2 hours, and when I start it manually I have the following message: pszInfo=!!!! no runtime license - running in demo mode(~2 hours) I tried using License Manager, and got the following message: Licensing info not available. There is no dongle attached to the device. I have this message frequently, and usually removing the content of /var/opt/codesys/.cmact_license makes it work. After doing it and restarting Codesys, I have an empty Softcontainer without my License. I tried using "Install license" using the .WibuCmRau file for the corresponding license and got the following message: Licensing info not available. The device does not support this service. I also tried using Additional Functions > Restore Licenses with the Ticket ID and got the following message: This device does not support automatic license backup. How can I reinstall the license to this Raspberry Pi?
Last updated: 2025-11-28

Post by dhumphries on codesys installer deletes itself instead of updating ^{CODESYS Forge talk (Post)}
I've installed multiple versions of codesys from a download, both the .exe and .zip, the installation goes okay but when I open the codesys installer with admin privelages it immediately starts downloading an update, then starts to install the update, but it doesn't complete the installation, it just deletes the installer files in c:\program files (x86)\codesys\apinstaller and never installs a new version. I've ran a repair from the downloaded installer and I can get it to work as long as I don't give admin permissions. I've done this on my workstation, I've also setup 2 different virtual machines thinking maybe there is some lingering config file, it does it no matter how sanitized the OS is. I've tried running with security software disabled and enabled, it's the same no matter what. It's been probably 4 months since I used the codesys installer, but it didn't do this back then. Is there a way to set the installer to a certain version and disable updates, or something I can do so the update does what it should?
Last updated: 2026-08-10

Post by tjacks on Opc UA Data Source Client Browse Error in Codesys HMI ^{CODESYS Forge talk (Post)}
Codesys V3.5 SP21 Patch 3 Codesys HMI 3.5.21.30 I'm trying to connect to an OPC UA server on a Kuka robot controller using Codesys HMI's data source manager. I get through the login phase and the client browses most of the data structure on the server but errors out toward the end with a generic: Error while browsing the client, Failed with service result: BadUnexpectedError. If I complete the data source setup and try to update variables, I get the attached stack trace for the error. I've tried several different endpoint and security options. Most get me through the login but all error out while browsing. UA Expert happily connects and browses with the same configuration. I've connected this same version of Codesys to TwinCAT OPC UA servers and Siemens PLC OPC UA servers. Any ideas on what may be causing the generic BadUnexpectedError during OPC UA server browse?
Last updated: 2025-11-17

Post by fredashbolt on Dynamically Update JSON Payload ^{CODESYS Forge talk (Post)}
I am trying to generate a JSON payload populated with a value that updates for use with a telemetry system, the payload is to be published by MQTT. I have established the MQTT client and can publish a working JSON payload but I can't get the payload to update as the value (iValue) changes. I am using a timer to trigger the .SetValue function periodically, but the JSON will only give the value as it is when it is first initialized using xFirst IF statement. Any suggestions? Thanks VAR pJsonData : POINTER TO JSON.JSONData := factory.Create(); fb_JBuilder : JSON.JSONBuilder; diRootIndex, diObject1Index : DINT; iValue : INT := 10 ; jsonArrayWriter : JSON.JSONByteArrayWriter; wsJsonData : WSTRING(1000); xFirst : BOOL := TRUE; utf8JsonData : STRING(2000); diTempVal : DINT ; PublishTimer : TON ; END_VAR IF xFirst = TRUE THEN fb_JBuilder ( pJsonData := pJsonData , diRootObj => diRootIndex ) ; diObject1Index := fb_Jbuilder.SetKeyWithObject ( "Device" , diParentIndex := diRootIndex ) ; diTempVal := fb_Jbuilder.SetKeyWithValue ( "Temp" , iValue , diParentIndex := diObject1Index ) ; xFirst := FALSE ; END_IF PublishTimer ( IN := PublishTimer.Q = 0 , PT := T#5S ) ; IF PublishTimer.Q THEN fb_JBuilder.SetValue ( iValue , diTempVal ) ; END_IF jsonArrayWriter( xExecute := PublishTimer.Q , pwData := ADR(wsJsonData), udiSize := SIZEOF(wsJsonData), jsonData := pJsonData^, xAsyncMode := FALSE ) ; JSON.Stu.ConvertUTF16toUTF8( ADR ( wsJsonData ) , ADR ( utf8JsonData ) , SIZEOF ( utf8JsonData ) , bStrictConversion := TRUE ) ;
Last updated: 2026-03-10

Post by chaylak on MC_ReadActualPosition with ST code ^{CODESYS Forge talk (Post)}
hi everyone, i am trying use MC_ReadActualPosition module in ST but i cant do it,( if i use CFC yes i read it) my axis is SoftMotion General Axis Pool->VirtAxisZ [Device: SoftMotion General Axis Pool] codesys V3.5 SP20 program: PROGRAM PLC_PRG VAR VirtAxisZ : AXIS_REF_VIRTUAL_SM3; fbPowerZ : MC_Power; fbReadPos : MC_ReadActualPosition; bEnable : BOOL := TRUE; lrActPos : LREAL; bValid : BOOL; bError : BOOL; fbResetZ : MC_Reset; xZ_Valid : BOOL; xZ_Busy : BOOL; xGlobalPower : BOOL; xGlobalReset : BOOL; xBtnTeachingMode : BOOL; lrGrvZ_OffsetTorque : LREAL := 0.5; lrPulseMmZ : LREAL; rPosFromBlock : LREAL; xZ_IsPowered : BOOL; xZ_PowerError : BOOL; iZ_PowerErrorID : LREAL; rZ_ActualPos : LREAL; lrTargetTorque : LREAL; sZ_ErrorString : STRING; //********** jog fbJogZ : MC_Jog; xJogForward : BOOL; xJogBackward : BOOL; rZ_ActVelocity : REAL; END_VAR fbResetZ( Axis:= VirtAxisZ, Execute:= xGlobalReset); fbPowerZ( Axis:= VirtAxisZ, Enable:= xGlobalPower, bRegulatorOn:= xGlobalPower, bDriveStart:=xGlobalPower , Status=> xZ_IsPowered, Busy=> xZ_Busy, Error=> xZ_PowerError, ErrorID=> iZ_PowerErrorID ); IF xGlobalPower THEN fbJogZ( Axis:= VirtAxisZ, JogForward:= xJogForward, JogBackward:= xJogBackward, Velocity:= 100, Acceleration:= 100, Deceleration:= 100, Jerk:= 1000); END_IF fbReadPos( Axis := VirtAxisZ, Enable := TRUE, Valid => bValid, Position => lrActPos, Error => bError ); IF VirtAxisZ.bError THEN sZ_ErrorString := 'Z Ex err'; ELSIF NOT xZ_IsPowered THEN sZ_ErrorString := 'Z Ex (Power Off)'; ELSE sZ_ErrorString := 'Z Ex Ready'; END_IF IF xBtnTeachingMode THEN lrTargetTorque := lrGrvZ_OffsetTorque; ELSE lrTargetTorque := 0; END_IF VAR_INPUT CFC_Motion: INT; END_VAR
Last updated: 2026-05-15

Post by timvh on JSONByteArrayWriter string result incorrect order ^{CODESYS Forge talk (Post)}
See the example below. You can insert key/value pairs as required At first the JSON string will be filled with: "{$"Key1$": $"Value0$", $"Key2$": [{$"Key3$": 1, $"Key4$": 2}]}" With xAdd, you can insert items, which will result in: "{$"Key1$": $"Value0$", $"Key2$": [{$"Key3$": 1, $"Key4$": 2},{$"Key3$": 3, $"Key4$": 4}]}" VAR factory : JSON.JSONDataFactory; eDataFactoryError : FBF.ERROR; pJsonData : POINTER TO JSON.JSONData := factory.Create(eError => eDataFactoryError); fb_JBuilder : JSON.JSONBuilder; wsValue : WSTRING; diRootIndex, diObjectIndex1, diObjectIndex2, diObjectIndex3 : DINT; iValue : INT; jsonArrayWriter : JSON.JSONByteArrayWriter; wsJsonData : WSTRING(1000); xFirst : BOOL := TRUE; xWrite: BOOL; xAdd: BOOL; END_VAR IF xFirst THEN fb_JBuilder.Reset(); fb_JBuilder(pJsonData := pJsonData, diRootObj => diRootIndex); wsValue := "Value0"; fb_JBuilder.SetKeyWithValue("Key1", wsValue, diParentIndex := diRootIndex); diObjectIndex1 := fb_JBuilder.SetKeyWithArray(wsKey := "Key2", diParentIndex := diRootIndex); diObjectIndex2 := fb_JBuilder.SetObject(diParentIndex := diObjectIndex1); iValue := 1; fb_JBuilder.SetKeyWithValue("Key3", iValue, diParentIndex := diObjectIndex2); iValue := 2; fb_JBuilder.SetKeyWithValue("Key4", iValue, diParentIndex := diObjectIndex2); xFirst := FALSE; xWrite := TRUE; END_IF IF xAdd THEN xAdd := FALSE; diObjectIndex3 := fb_JBuilder.SetObject(diParentIndex := diObjectIndex1); iValue := 3; fb_JBuilder.SetKeyWithValue("Key3", iValue, diParentIndex := diObjectIndex3); iValue := 4; fb_JBuilder.SetKeyWithValue("Key4", iValue, diParentIndex := diObjectIndex3); xWrite := TRUE; END_IF IF xWrite THEN xWrite := FALSE; jsonArrayWriter( xExecute := TRUE, wsLinebreak := "", pwData := ADR(wsJsonData), udiSize := SIZEOF(wsJsonData), jsonData := pJsonData^, xAsyncMode := FALSE ); END_IF IF jsonArrayWriter.xDone OR jsonArrayWriter.xError THEN jsonArrayWriter(xExecute := FALSE, pwData := ADR(wsJsonData), udiSize := SIZEOF(wsJsonData), jsonData := pJsonData^, xAsyncMode := FALSE); END_IF
Last updated: 2026-06-14

Post by megasilver on Cannot download program to CR1074 – Version mismatch error ^{CODESYS Forge talk (Post)}
Hello, I am having a problem downloading my application to an ifm CR1074 using CODESYS. When I try to download the program to the controller, I get the following errors: [FATAL ERROR] Version mismatch at: 'KEYBOARD_SET_MAPPING' Requested version: 2.0.0.12 Implemented version: 3.4.0.0 [FATAL ERROR] Version mismatch at: 'SYSCFG_SPLASH_SET_SPLASH_SCREEN_VISIBLE' Requested version: 2.0.0.12 Implemented version: 3.4.0.0 [FATAL ERROR] Version mismatch at: 'SYSTEM_IO_BACKLIGHT_SET_CURRENT_BACKLIGHT_BLOCKING' Requested version: 2.0.0.12 Implemented version: 3.4.0.0 [FATAL ERROR] Version mismatch at: 'SYSTEM_IO_BACKLIGHT_SET_CURRENT_BACKLIGHT' Requested version: 2.0.0.12 Implemented version: 3.4.0.0 [FATAL ERROR] Version mismatch at: 'KEYBOARD_RESET_LEDS_BLOCKING' Requested version: 2.0.0.12 Implemented version: 3.4.0.0 [FATAL ERROR] Version mismatch at: 'KEYBOARD_SET_LED_COLOR' Requested version: 2.0.0.12 Implemented version: 3.4.0.0 [FATAL ERROR] Version mismatch at: 'SYSCFG_DEVINFO_GET_KEYBOARDS_INFO' Requested version: 2.0.0.12 Implemented version: 3.4.0.0 The controller is running an OS version that should be compatible with CODESYS 3.5 SP16, and I am using the latest available ifm/ecomatDisplay package for this OS version. Therefore, I do not think this is simply a CODESYS or OS compatibility issue. It looks like the application expects system functions with version 2.0.0.12, while the controller implements version 3.4.0.0. Could this be caused by an incorrect or outdated library, device description, package installation, or a mismatch between the libraries used in the project and the libraries installed on the CR1074? What would be the correct way to identify which component is requesting version 2.0.0.12 and how can I resolve this version mismatch? Thank you for your help.
Last updated: 2026-08-21

Post by nickpoon on SysProcessCreate stopped working after SP21? ^{CODESYS Forge talk (Post)}
I'm going through the process of updating the CODESYS Project a machine to 3.5 SP21 (old version was 3.5 SP20). One function that stopped working when upgrading was SysProcessCreate. I need to run a .exe file that is located in C:\Program Files\MQTTStream. Some initial searching suggested that there are new security rules that prevent the SoftPLC from reading/writing files to outside of its Device folder (located here - C:\Windows\System32\config\systemprofile\AppData\Roaming\CODESYS\CODESYSControlWinV3x64\24FD6770) Relocating files helped fix my JSON file reader/writer functions (which were failing previously), but not the case for SysProcessCreate. I've even attempted to just run window's cmd.exe and with: pszCommandLine = 'cd /d C:\Windows\System32\config\systemprofile\AppData\Roaming\CODESYS\CODESYSControlWinV3x64\24FD6770\PlcLogic\MQTTStream & sift-proxy.exe --grpc_uri="https://grpc-api.siftstack.com" --api_key="xxxxxxxxxxxxxxxxxxx" mqtt-client --broker_ip=10.0.10.101 --broker_port=1883 --config_file="mqtt_telemetry_config.json" --username Plantd --password 1234 --stream_metrics --storage_path="sift-proxy-logs"' I have not been able to find a lot of documentation on this, and I suspect the new update may have created a bug for SysProcessCreate. Any help would be greatly appreciated
Last updated: 2026-02-02

Post by konstantin on CAM Motion Recover after STO ^{CODESYS Forge talk (Post)}
Hello Mr. Seidel, both the master and the slave axis are modulo. Basically the situation is as follows: One master cycle is 100 units. Slave's modulo length is 2000 units. In the CAM table I defined 10 master cycles on X axis - 1000 units and on the Y axis is the slave - 2000 units. Then depending on the master position 0 to 1000 units the slave's position is plotted on the Y axis - 0 to 2000 units. For example, while the master is executing the 3rd cycle i.e. above 200 units, I trigger the STO function of the slave and it stops. The master executed his cycle but the slave was stopped during the execution. How can I set the slave to continue the CAM sequence from the point where it stopped i.e. third cycle of the master? When I reset the slave error and sync again, everyrhing starts from master's 0 position. Best Regards Konstantin Kolev
Last updated: 2026-02-13

Post by kunal-pinetics on USB Communication for IP Configuration & Application Update – STM32H Series PLC ^{CODESYS Forge talk (Post)}
Hello everyone, I am currently working on a PLC device based on the STM32H series MCU, running CODESYS. At the moment, I can: Change the Ethernet IP address Update/download the PLC application via Ethernet without any issues. However, I would like to implement the same functionality over USB (or Serial via USB) instead of Ethernet. My goals are: Change the device’s Ethernet IP address via USB Download/update the PLC application via USB communication Possibly use USB as a service/programming interface The hardware platform is based on STM32H series, and I am looking for guidance on: Whether CODESYS supports USB device communication for runtime download If a custom USB CDC (Virtual COM Port) implementation is required Whether a specific CODESYS runtime configuration is needed If a bootloader approach is recommended for application updates via USB If anyone has experience implementing USB communication for runtime download or device configuration on an STM32-based PLC, I would really appreciate your guidance. Thank you in advance for your help.
Last updated: 2026-02-26

Post by yannickasselin on CloseTargetVisu ^{CODESYS Forge talk (Post)}
To shutdown the TargetVisu: Add the VisuElemBase library to your project then call VisuElemBase.Visu_PRG.RemoveAllTargetVisuClients(); Exemple: PROGRAM PLC_PRG VAR xShutdownTargetVisu: BOOL; END_VAR ---------------------------------- IF xShutdownTargetVisu THEN xShutdownTargetVisu := FALSE; VisuElemBase.Visu_PRG.RemoveAllTargetVisuClients(); END_IF I tried calling RemoveAllTargetVisuClients() directly from a button mouse click event but it makes the Visu crash. So better using the code above and just set xShutdownTargetVisu to TRUE from the button. Works fine for me. To start the TargetVisu: From a cmd prompt. This will start the TargetVisu C:\Program Files\CODESYS\CODESYS Control RTE3>VisualClientController.exe --application=Application --flags=1 You can then place a .bat file on the desktop and put this inside: CD "C:\Program Files\CODESYS\CODESYS Control RTE3" VisualClientController.exe --application=Application --flags=1 exit Double clicking the .bat file will start the TargetVisu. You may need to replace the Application name by your own application name. Good to know: In the cmd above, if you replace --flags=1 by --flags=2, it will shutdown the TargetVisu.
Last updated: 2026-03-11

Sort by relevance or date