Post by pmanuele on Beckhoff AS1060 and EL7041 configuration ^{CODESYS Forge talk (Post)}
Hello everyone, i'm having some problems commanding AS1060 step motor with EL7041 (rev22) drive. With motor i've also the incremental encoder (05.2420.1230.0200.5009). I can correctly move the motor in "Position controller" operating mode with the internal counter. The problems start when i set the Encoder in feedback type or i change the operating mode. Does anyone have experience with these two terminals and can give me some advice of main parameters to check or change? Thanks everyone
Last updated: 2024-12-11

Post by aliazzz on Runtime licenses not detected => DEMO Mode 2hour ^{CODESYS Forge talk (Post)}
Hi! After upgrading all my licensed runtimes to V4.14.0.0 (= RaspberryPi SL, LinuxSL and ControlWin x64 SL) I found out via the logfiles they all defaulted back into DEMO mode while all runtimes have a USB dongle inserted. So, my main question is how I can get the Dongle license detected? I use License Server 4.14.0.0 and Edge Gateway 4.14.0.0 on all platforms Any suggestions are welcome.
Last updated: 2024-12-15

Post by bruno-roth on Read "Homed" status from EtherCAT drive ^{CODESYS Forge talk (Post)}
Hello, the information if your axis is already homed you could only find out direct from your Slave. In DS402 status there is no Bit defined. But some manufacturer of Drives use some optional bits or status. E.g. if you have Schneider Electric LXM32 Servo you will find this information in Bit 15. You have to check the manual of your used Servo-Drive f this information is provided in any object and then read it out with SDO.
Last updated: 2025-01-08

Post by teichhei on The selected container ... does not fit your ticket ^{CODESYS Forge talk (Post)}
Update, installed 3.5.19.70 with the same result. The error message is as useful as a chocolate fire guard. The container SN is in the 130-xxx range which should work. The Version, Chip, Rev number don't mean anything to me. There is no SD Card installed. I've also reinstalled a fresh Wago FW22 image, Deployed PFC200 SL and Edge for Linux, still the same result.
Last updated: 2025-01-09

Post by askic on PLC error log help ^{CODESYS Forge talk (Post)}
Hello, I'm using Codesys 3.5.20.0 version and I noticed that even with the most basic standard project create, there are error messages like shown in the acttached picture. The similar questions are already asked here on the CODESYS Forge Talk, but remained unanswered. Exact screenshot is attached, but essentially I would like to know which component in the Codesys has CmpID = 0x00000019 and what this Timeout means?
Last updated: 2025-01-10

Post by paulpotat on Can't find the safety manual in the documentation ^{CODESYS Forge talk (Post)}
Hello, I was browsing the "CODESYS Virtual Safe Control for Linux SL" documentation page, and it says the following : For more information about the development of safety-critical applications with CODESYS, see: * Safety Manual H1 – SafetyManual.pdf, which is stored in the directory ../<user>/CODESYS Virtual Safe Control Linux SL/Delivery/Manuals</user> What does this path refers to ? I can't find it in CODESYS installation directories. Best regards
Last updated: 2025-01-23

Post by timvh on Codesys Runtime Devie Password ^{CODESYS Forge talk (Post)}
This has been moved because of security reasons. But it depends on how you start CODESYS where the project files are located (at least for Control Win from SP20). 1) If you start it through the sys tray icon, you start it as a service and the files will be located in: C:\Windows*System32\config\systemprofile\AppData\Roaming\CODESYS... (or C:\Windows*SysWOW64**\config...) 2) If you start it as a user, e.g. with a shortcut to the runtime, you can find it in: C:\Users\<your user="" name="">\AppData\Roaming\CODESYS...</your>
Last updated: 2025-02-11

Post by pernockham on Inheritence of struct, ^{CODESYS Forge talk (Post)}
Interesting, thanks! Didnt know about ANY before, and will sure find a use-case for it. Im not sure it will help me here though, it seems to me that an ANY will not accept a string assignment? I actually think that the "ALIAS" should work, that was a hard found error. I had a fair bit of scratching my head looking for misdirected pointers before I understood what was (not) happening. I will use the work-around of individual structs instead.
Last updated: 2025-03-08

Post by patrik on windows runtime crashes. ^{CODESYS Forge talk (Post)}
Faulting application name: CODESYSControlService.exe, version: 3.5.20.30, time stamp: 0x66ebc91d Faulting module name: unknown, version: 0.0.0.0, time stamp: 0x00000000 Exception code: 0xc0000005 Fault offset: 0x0000028010670e31 Faulting process id: 0x0x1F50 Faulting application start time: 0x0x1DB1BA284347B9C Faulting application path: C:\Program Files\CODESYS 3.5.20.30\GatewayPLC\CODESYSControlService.exe Faulting module path: unknown Report Id: d3ac6a03-667a-4d61-ab36-d2ae703fc252 Faulting package full name: Faulting package-relative application ID: My runtime crashes from time to time. I'm not getting anything in the PLC logs. This is from the windows logs. Can anyone help me understand why this is happening?
Last updated: 2025-03-19

Post by lamine97 on Issue with Timer-Based Increment Function in CoDeSys Ladder Logic (LD) ^{CODESYS Forge talk (Post)}
I am trying to implement a Ladder Logic (LD) function block in CoDeSys that increments a value A by B every T time interval. My Structured Text (ST) version works perfectly in simulation, but when I implement it in LD, it does not work. The ST code: PROGRAM ADDITION VAR_INPUT A : LREAL ; B : LREAL ; T : TIME ; END_VAR VAR Timer : TON ; END_VAR Timer (IN:=TRUE, PT := T); IF Timer.Q THEN A := A + B ; Timer(IN := FALSE ) ; END_IF;
Last updated: 2025-03-25

Post by wbj0t on Update project from SP20 to SP21 ^{CODESYS Forge talk (Post)}
Hello everyone. I have a problem: I installed new version of codesys IDE. When I try open project in this new version, I have many errors about Visu: rectalnge/button/frame/etc does not exist. How update properly project? 20+ pages of visu pages from 100+ frames and all visu elems looks like "Error image". It is not problem of SP20->SP21. Any update has problems from visu side.
Last updated: 2025-06-09

Post by josul on Web Client HTTPS Communication Issue ^{CODESYS Forge talk (Post)}
Thank you for the suggestion. There is a certificate created in the quarantine directory relating to the URL used for the webclient FB. This certificate should have been valid as it was created only the week before this problem was encountered. I investigated a separate location using the same https URL and it has 2 certificates in the same quarantine directory, 1 is created almost 200 days ago, the other over 100 days ago. There have been no similar problems encountered with these certs or https at all.
Last updated: 2025-06-09

Post by berkdan on SMC_ReadNCFile2 is always busy ^{CODESYS Forge talk (Post)}
Hey tk96 Thank you for your help. I have found the reason why fbreader stuck. It was not the program but it was the gcode itself. G21 command blocks the reader. And multiple G codes in a line also blocks the reader. My code was: N010 G21 G17 G90 -> Blocked the reader When i change it to: N010 G90 N020 G17 Then it worked. The only thing i did not get is why the reader did not thwor error. ErrorId was SMC_NO_ERROR. Anyway, it is now working. Thanks again.
Last updated: 2025-06-17

Post by nguyenkhoi on Omron R88D-KN08H-ETC with a raspberry on top... (over ethercat) ^{CODESYS Forge talk (Post)}
hi everyone, continuing the part about omron g5 axis and nx-ecc201 omron, but i have a problem with not being able to scan with "model with Z code suffix of omron china", it seems that the available softmotion file is not fully compatible mapping, often causing ethercat communication error DC distributed clock after every 10-12 hours of continuous running! omron driver: R88D-KN08H-ECT-Z
Last updated: 2025-07-01

Post by jari-koivuluoma on Finding out exception code position ^{CODESYS Forge talk (Post)}
Is it possible to find out the code position from where the exception originated using information from this log entry? 2025-07-02T13:56:19Z, 0x00000011, 8, 81, 3, #### Exception: *EXCEPTION* [<excpt>AccessViolation</excpt>] occurred: App=[<app>Application</app>], Task=[<task>Task</task>] 2025-07-02T13:56:19Z, 0x00000011, 8, 81, 3, #### Exception: *SOURCEPOSITION* App=[<app>Application</app>] area=<area>2</area>, offset=<off>13349868</off>
Last updated: 2025-07-02

Post by yuan on Seeking a Code-Based Solution for EtherCAT Slave Dropout or Master Errors in Production (Beyond Software Hot Reset) ^{CODESYS Forge talk (Post)}
I need official assistance with the following issue: During EtherCAT communication, if a slave station drops off the network or the master station encounters an error, the problem can currently only be resolved by performing a software-based hot reset. In actual production environments, this approach is unacceptable. Is there a method to resolve these issues programmatically, through code?
Last updated: 2025-07-18

Post by imdatatas on MC_MoveAbsolute: C0138: No matching 'FB_Init' method found for instantiation of SMC_MoveAbsRelPerformerImpl [ERROR] ^{CODESYS Forge talk (Post)}
Hello everyone, Updating and converting an existing working Codesys Softmotion axis control project to the latest Codesys IDE and Softmotion version always gives the following error message during compilation. " [ERROR] sm3_basic, 4.18.0.0 (codesys): MC_MoveAbsolute: C0138: No matching 'FB_Init' method found for instantiation of SMC_MoveAbsRelPerformerImpl " -- Previously working version: Codesys IDE SP18.50, Softmotion 4.10.0.0 -- Later updated version with the error: Codesys IDE SP21.10, Softmotion 4.18.0.0 Has anyone encountered a similar issue? How can this be resolved? Regards, Imdat
Last updated: 2025-07-24

Post by jeroenaero on Autostart Targetvisualization 4.16.0.0 doesn't work on Linux device ^{CODESYS Forge talk (Post)}
Hi, How can we configure autostart of TargetVisualization on the remote device? The device is a Raspberry PI CM4 with PIXEL Desktop on display. I installed Targetvisu for Linux SL 4.16.0.0 on it. After each restart of the Raspberry PI CM4, we have to start Targetvisu fot Linux SL manually. i tried the step on this page: https://content.helpme-codesys.com/en/CODESYS%20Control/_rtsl_target_visu_for_linux.html but i don't get it working
Last updated: 2025-07-24

Post by eschwellinger on Changed Device of Rapberry Pi to MC SL instead of standard SL and cannot connect anymore ^{CODESYS Forge talk (Post)}
1) https://store.codesys.com/en/codesys-control-for-raspberry-pi-sl.html -> SL: Restrictions The combination of Raspberry Pi and a CODESYS Runtime is for private use, test and teaching purposes. Commercial use is not permitted. 2) you could switch between them by /etc/codesyscontrol/CODESYSControl_User.cfg [CmpRasPi] Architecture=armv7l for MC: armv7l for SC: armv6l for 64Bit: aarch64 or in the Deploytool:
Last updated: 2025-08-06

Post by yannickasselin on Dynamically enabling/disabling Modbus slave devices in runtime (performance issue with timeouts) ^{CODESYS Forge talk (Post)}
I would definitely try using the "Reconfigure" function block from "CAA Device Diagnosis@ library. https://content.helpme-codesys.com/en/libs/CAA%20Device%20Diagnosis/3.5.17.0/CAA-Device-Diagnosis/Function-Blocks/Reconfigure/Reconfigure.html#:~:text=This%20function%20block%20reads%20and,take%20effect. Although I have not tried it with Modbus, I had great success with EtherNet/IP, Profinet and EtherCAT. You can also have a look at the other functions in this library. There are useful functions to help iterate through all the nodes under a master node.
Last updated: 2025-08-12

Post by monw on Unable to Re-Import Native XML Exported Using CODESYS Script API ^{CODESYS Forge talk (Post)}
When exporting a Logical Device or Logical Exchange GVL using the native XML export functionality of the CODESYS Script API, I encounter the following error upon re-import: "Error in IEnumeratorOfTWrapper. Current. Could not cast: System.String in System.Char" I am using CODESYS V3.5 SP21 Patch 2. Is there a known solution or workaround for this issue? Notably, importing the same XML file through the CODESYS Engineering IDE's menu import works without error.
Last updated: 2025-09-12

Post by gunstr on CODESYS control on RPi starts, shortly runs, then exits ^{CODESYS Forge talk (Post)}
The problem has been resolved. Two findings are described below for future reference. The new RPi hw delivered during August 2025 has a MAC address from a new vendor series that is not supported by old runtimes. 4.17.0.0 or above is required. 4.17.0.0 does not pick up the correct architecture during installation and aarch64 has to be manually configured either in the GUI under operations or in /etc/codesyscontrol/CODESYSControl_User.cfg under the [CmpRasPi] section.
Last updated: 2025-09-16

Post by nchau on Requesting ESI Files for Estun Pronet Servo Drives (EtherCAT) ^{CODESYS Forge talk (Post)}
Hi everyone, I'm currently working on a project using Estun Pronet servo drives with EtherCAT communication, and I need the appropriate ESI (EtherCAT Slave Information) files to set up the network. The specific models I'm using are: Pronet-04AEG-EC Pronet-02AEG-EC-R1 Pronet-10AEG-EC-R1 Pronet-20AEG-EC-R1 Pronet-50DEA-EC-R1 If anyone has the ESI files for these models or knows where I can download them, I would greatly appreciate your help. Thank you in advance!
Last updated: 2025-09-26

Post by nchau on Estun servo with codesys ^{CODESYS Forge talk (Post)}
Hi everyone, I'm currently working on a project using Estun Pronet servo drives with EtherCAT communication, and I need the appropriate ESI (EtherCAT Slave Information) files to set up the network. The specific models I'm using are: Pronet-04AEG-EC Pronet-02AEG-EC-R1 Pronet-10AEG-EC-R1 Pronet-20AEG-EC-R1 Pronet-50DEA-EC-R1 If anyone has the ESI files for these models or knows where I can download them, I would greatly appreciate your help. Thank you in advance!
Last updated: 2025-09-26

Post by alexgooi on Licensing info not available. ^{CODESYS Forge talk (Post)}
Dear Eschwellinger, Thank you for the response. Does that mean that the license-manager inside the Codesys-IDE does not work with this setup anymore? Because when I use this I get the notification that there is no dongle attached to the device (see picture). And If I insert the license by the deploy tool, can I then redeploy the Codesys virtual control container, or does this erase the license completely?
Last updated: 2025-09-30

Sort by relevance or date