Post by sumit on Remote Ethernet/ip Adapter communication with scanner running on codesys ^{CODESYS Forge talk (Post)}
Hello there, I have my ethernet/ip adapter (from Texas Instrument) running on Texas Instrument Board and I have configured the scanner on codesys. I have mapped the I/Os and I can see (on wireshark) the frames coming from adapter but I don't see my input variables in scanner get updated, they just stay at 0. I wanted to see the real data that has been sent from adapter to scanner on codesys. I am not sure if the problem is in I/O mapping or there is a step/s that I have missed. I have attached the screenshot of my project for your ref. Thank you, Sumit
Last updated: 2023-12-15

Post by dhumphries on Codesys device configuration ^{CODESYS Forge talk (Post)}
First make sure the programming laptop and HMI are both on the same subnet. For example if the IP address of the HMI is 192.168.1.125 with a subnet mask 255.255.255.0 set your laptop IP to 192.168.1.120 with a subnet mask of 255.255.255.0. Make sure the cables are fully connected (the ethernet port on my programming laptop will click once but the cable is not fully seated.) Make sure the HMI is powered on, try pinging the device from a command prompt, if you can't ping the HMI there is a network issue that has to be resolved first.
Last updated: 2023-12-30

Post by arundara on OPC UA Server Stops after 5 consecutive disconnections of ethernet port ^{CODESYS Forge talk (Post)}
Hello Every one, During testing of OPC UA communication between UA Expert software and the CODESYS SoftPLC on a Linux environment, an observation was made. When the Ethernet cable was disconnected and reconnected with 2-minute intervals, on the 5th attempt, the OPC UA connection failed to establish in UA Expert software. At this juncture, restarting the CODESYS SoftPLC enabled the reestablishment of OPC UA communication. The same result was obtained when testing on a Raspberry Pi SoftPLC. What is the reason behind this phenomenon? and whether there are settings to stop this behavior? Please help. Thanks & Regards.
Last updated: 2024-02-13

Post by hafizapik99 on Webvisu not showing Codesys V3.5 SP13 Patch 2. ^{CODESYS Forge talk (Post)}
Hello, I am using a Hitachi Micro EHV+ for a small project, and I wanted to have a Web visu, done with Codesys V3.5 SP13 Patch 2. I test the Visu screen and it works well in Codesys, but I get a blank page when i enter the web visu in a browser. Here is the setting under web visualization: Update rate (ms): 5000 Default communication size: 100000 Under Visu_Task tab: Priority: 3 The Visu_Task interval is set to 2500ms I'm using Google chrome with the latest update, the Javascript is enabled with HTML5. Any advice?
Last updated: 2024-04-06

Post by saugat10 on Cannot install Codesys control Multicore in raspberry pi 4 ^{CODESYS Forge talk (Post)}
I have raspberry pi 4 with Raspbian 12 (bookworm). I want to install the latest version of codesys control 4.11.0.0 multicore for 32 bit. I cannot install multicore and it only gives me the option to install Standard. Here are some outputs from the pi pi@saugat:/usr $ uname -a Linux saugat 6.6.20+rpt-rpi-v7l #1 SMP Raspbian 1:6.6.20-1+rpt1 (2024-03-07) armv7l GNU/Linux pi@saugat:~ $ cat /etc/os-release PRETTY_NAME="Raspbian GNU/Linux 12 (bookworm)" NAME="Raspbian GNU/Linux" VERSION_ID="12" VERSION="12 (bookworm)" VERSION_CODENAME=bookworm ID=raspbian ID_LIKE=debian HOME_URL="http://www.raspbian.org/" SUPPORT_URL="http://www.raspbian.org/RaspbianForums" BUG_REPORT_URL="http://www.raspbian.org/RaspbianBugs" A
Last updated: 2024-04-22

Post by reinier-geers on License problem gateway ^{CODESYS Forge talk (Post)}
Epis doesnt want Softmotion. I thought it was about the price. If it was possible it would be working already and i dont need an extra licence. Thats the problem of codesys. The software is running but hangs on its license. Epis made it posible to see the stick. I can see the license. Softmotion is there from 3.5.14.Xx Like is said And Motion control is alrady posible 15 year ago. And i only need a Sync of 2 drives. I want a good solution not a refund. Dont point to the manufacturer. The software is made by 3s not by epis .
Last updated: 2024-04-29

Post by dhumphries on Rounding error in simple addition ^{CODESYS Forge talk (Post)}
Thanks for the response, as I've thought about this problem over the last month I began to suspect this was a problem with not being able to exactly represent .1 as a 32 bit binary number. I think I've found a work around by making the number an integer, then dividing it by 10 and storing that value as a floating point number. There is still an issue with the value not being exact somewhere in the 8th or 9th decimal place, but because I'm incrementing an integer value then dividing it, the error doesn't compound.
Last updated: 2024-05-25

Post by jaspergain on Non-existing identifiers ^{CODESYS Forge talk (Post)}
Hello, I got a bit of a weird issue going on which is kind of annoying. So recently we switched a lot of Modbus IO to EtherCAT, as we were having issues with stability. All works fine, which is great. But sometimes when I change the program I get errors claiming that identifiers are not defined. Meaning I can't go online. See the picture below. I believe this is because some of these identifiers were used with Modbus, and they weren't properly removed/deleted? A clean all temporary fixes the issue, but it comes back again after a while of changing the code, and building. Any way to fix these non-existing required identifiers, or even find out where they are required? Thanks for the help in advance. Jasper.
Last updated: 2024-05-29

Post by kuegerls on SysProcessExecuteCommand2 and CANopen Device ^{CODESYS Forge talk (Post)}
Hello, CODESYS Control is running on my RevPi, and my system communicates over a CANbus with a master using the ConnectCan module (Slave - CANopen Device). The communication works perfectly fine so far. However, as soon as I call a Python script with "SysProcessExecuteCommand2" that creates a CSV file and executes without errors, the master does not adopt any changes to the Transmission Process Data Objects (TPDOs). I don't quite understand what one has to do with the other, and perhaps someone can help me with this. Here is my script call: SysProcess.SysProcessExecuteCommand2(pszCommand:='python /home/pi/test.py', pszStdOut:=sCMDOutput, udiStdOutLen:= SIZEOF(sCMDOutput), pResult := ADR(eResult)); Thank you in advance! Best regards, Stefan
Last updated: 2024-06-20

Post by imdatatas on Codesys IDE initialization error from a new Sandbox image ^{CODESYS Forge talk (Post)}
Hello everyone, I created a new sandbox image on the D drive with Codesys Installer. However, when I launch the IDE from this image, it gives the error shown in the attached image. -- Codesys V3.5 SP19 Patch7. -- The installer is the latest (2.5.0). -- All packages in the installer were updated to the latest version as of today when creating the sandbox. -- The originally installed IDE on the C drive does not give this error when launched. -- I last upgraded it to Softmotion 4.20.1.0 through the installer. Has anyone encountered the same or a similar issue? Will this issue be fixed in the next update? Best regards, Imdat
Last updated: 2025-12-05

Post by aleksahin6824 on SysEthernet error ^{CODESYS Forge talk (Post)}
Good afternoon Please help with localizing the error. Periodically, but on the same time grid, the error SysEthernet: packet could not be sent occurs. PLC and motors from XINJE. PLC — XSA-330L, rev. 1.2, drivers — DC5C2 (rev.5) In the task configurator, all tasks are set to simple numbers (11, 13, 41 ms) for convenience. The jitter for EtherCat and SoftMotion tasks is less than the task cycle (2 ms jitter for a 6 ms task). The power supply is sufficient for both the PLC and the motors. The cables are in good condition. Please suggest where to look for the problem. P.S. The PLC uses proprietary Linux and there is no SSH access.
Last updated: 2026-08-30

Post by aleksahin6824 on SysEthernet error ^{CODESYS Forge talk (Post)}
Good afternoon Please help with localizing the error. Periodically, but on the same time grid, the error SysEthernet: packet could not be sent occurs. PLC and motors from XINJE. PLC — XSA-330L, rev. 1.2, drivers — DC5C2 (rev.5) In the task configurator, all tasks are set to simple numbers (11, 13, 41 ms) for convenience. The jitter for EtherCat and SoftMotion tasks is less than the task cycle (2 ms jitter for a 6 ms task). The power supply is sufficient for both the PLC and the motors. The cables are in good condition. Please suggest where to look for the problem. P.S. The PLC uses proprietary Linux and there is no SSH access.
Last updated: 2026-08-30

Post by bigwhig on Could not write options file at... ^{CODESYS Forge talk (Post)}
Using Codesys 3.5.21.5. Tried installing both by full .exe file and using codesys installer. Installation requires elevation and completes just fine. However when running Codesys and closing the IDE, options-files are not written: Seems regular users are only given read-access to these files: Running Codesys as admin works as admins have full access. Haven’t been necessary before to run as admin. Don’t think I have the issue on my work-laptop, but have experienced this on a number of other computers. Above screenshots are from my private stationary running Windows 11 Pro: Anyone else experiencing this? Is this by design or a known issue?
Last updated: 2026-09-04

Post by harryc on Soft Container License issue with ARM64 Linux ^{CODESYS Forge talk (Post)}
Hi, We are working to provide our customers with CODESYS operation on our hardware product ( https://elprotech.com/product/el-qe-e-quantum-edge-series/ ). I'm trying to enable a CODESYS license (Soft container) on our product running ARM64 linux. This problem am having looks similar to here: https://forge.codesys.com/forge/talk/Runtime/thread/6d29b6b4de/ and here: https://forge.codesys.com/forge/talk/Runtime/thread/a2d0c63375/; but I am not running docker, and I am not re-installing a license. This is first time install. I have CODESYS Control SL running on my device, as well as CodeMeter. I purchased a license, and installed it to the CODESYS Development system, (Tools >> License Repository) then tried to install to the device (Tools >> License Manager >> o Device >> o Soft container >> Remote [0001] >> OK. This gives me the "License Manager - Overview" dialog, and the message "Licensing info not available. There is no dongle attached to the device." Below shows the running applications, installed packages, and current content of /var/opt/codesys Also attached screenshots of the Development software as I go through the steps to install the license. # # ps | grep -e "code" -e "CodeMeter" 1391 daemon /usr/sbin/CodeMeterLin 1407 root /opt/codesys/bin/codesyscontrol.bin /etc/codesyscontrol/CODESYSControl.cfg 1442 root /opt/codesysedge/bin/codesysedge.bin /etc/codesysedge/Gateway.cfg 29229 root grep -e code -e CodeMeter # dpkg -l Desired=Unknown/Install/Remove/Purge/Hold | Status=Not/Inst/Conf-files/Unpacked/halF-conf/Half-inst/trig-aWait/Trig-pend |/ Err?=(none)/Reinst-required (Status,Err: uppercase=bad) ||/ Name Version Architecture Description +++-==============-=============-============-============================================================================================== ii codemeter-lite 8.20.6539.500 arm64 WIBU CodeMeter minimal runtime ii codesyscontrol 4.14.0.0 arm64 codesyscontrol based on SDK 3.5.20.40 , from Fri Nov 29 08:35:37 CET 2024 [265], Release build ii codesysedge 4.14.0.0 arm64 codesysedge based on SDK 3.5.20.40 , from Fri Nov 29 08:34:19 CET 2024 [265], Release build # ls -la /var/opt/codesys total 208 drwxr-xr-x 6 root root 4096 Nov 7 05:31 . drwxr-xr-x 1 root root 4096 Nov 6 08:33 .. -rw-r--r-- 1 root root 23515 Nov 7 07:26 .Audit.log -rw-r--r-- 1 root root 160 Nov 7 05:31 .GroupDatabase.csv -rw-r--r-- 1 root root 160 Nov 7 04:37 .GroupDatabase.csv_ -rw-r--r-- 1 root root 20736 Nov 29 2024 .SoftContainer_CmRuntime.wbb -rw-r--r-- 1 root root 1982 Nov 29 2024 .UFC_SoftContainer_CmRuntime.WibuCmLif -rw-r--r-- 1 root root 229 Nov 7 04:35 .UserDatabase.csv -rw-r--r-- 1 root root 229 Nov 7 04:35 .UserDatabase.csv_ -rw-r--r-- 1 root root 11807 Nov 7 05:30 .UserMgmtRightsDB.csv drwxr-xr-x 6 root root 4096 Nov 6 08:30 .pki drwxr-xr-x 3 root root 4096 Nov 6 08:30 OPCUAServer drwxr-xr-x 7 root root 4096 Nov 6 08:30 PlcLogic -rw-r--r-- 1 root root 13 Nov 6 08:30 SysFileMap.cfg -rw-r--r-- 1 root root 2640 Nov 29 2024 bacstac.ini drwxr-xr-x 4 root root 4096 Nov 6 08:30 cert -rw-r--r-- 1 root root 94105 Nov 7 07:25 codesyscontrol.log # # uname -a Linux Remote 6.1.22 #5 SMP PREEMPT Tue Nov 18 11:35:46 AEST 2025 aarch64 GNU/Linux #
Last updated: 2025-12-04

Post by reinier-geers on wEBCLIENT Post data api ^{CODESYS Forge talk (Post)}
Ive got the webclient axample. If i put https://reversed.notion.site/Marktprijzen-API-89ce600a88ac4abe8c2ad89d3167a83e example to https://reqbin.com/post-online then i get data. If i do the same in Webclient example i get " not a valid graphql request. Why ? sUrl := 'https://graphql.frankenergie.nl/' Request_type_post Contenttype = 1 (json ) Postvalue := '{"query":{"query":"query MarketPrices {\n marketPrices(date:\"2025-12-25\") {\n electricityPrices {\n from\n till\n marketPrice\n marketPriceTax\n sourcingMarkupPrice\n energyTaxPrice\n perUnit\n }\n gasPrices {\n from\n till\n marketPrice\n marketPriceTax\n sourcingMarkupPrice\n energyTaxPrice\n perUnit\n }\n }\n}' I tranfer the postvalue from String to WSTRING
Last updated: 2025-12-25

Post by julianramirez on Visu 4.9.1 auto-logon/login ^{CODESYS Forge talk (Post)}
Hello everyone, I have been trying to test the auto-login feature that is advertised on the Release Notes since Visu 4.8: *Version: 4.8.0.0 Besides some bug fixes and improvements this version contains the following new functionality: Alarmmanagement: Possibility to raise alarms programmatically Use real time clock of IEC context Automatic login for WebVisu using Chrome "Sign in automatically"* I am using a personalized login Visualization, the User Management works, however, when ticking the checkbox that keeps the credentials stored, after I reload the page I still see that the user and password details are not filled in. I tried with the default Login Visu (Blue one), and still see the same behavior - VisuUserManagement.VUM_LoginVisualization - I've tried with Chrome and Edge. Thanks for your help
Last updated: 2026-01-12

Post by baotthitawat on Why Structured SCADA Documentation Matters in Modern Industrial Systems ^{CODESYS Forge talk (Post)}
Modern SCADA development is no longer limited to monitoring dashboards and PLC communication. Today’s industrial systems often require: Cloud architecture Web & mobile SCADA API integration IIoT communication Alarm management Scalable deployment workflows One challenge in many projects is that deployment knowledge is usually scattered across multiple documents, configuration guides, and troubleshooting references. As systems become more connected, engineers need a more structured learning approach to reduce deployment time and improve maintainability. The ATSCADA Training Book is an interesting example because it organizes the ecosystem into a clearer roadmap covering: SCADA architecture Driver & OPC communication Web visualization Mobile applications Cloud & IIoT systems Troubleshooting & maintenance I think structured technical documentation will become increasingly important as industrial automation systems continue evolving toward larger and more connected environments.
Last updated: 2026-05-27

Post by egerobotics on [New Hardware] EtherCAT Digital & Analog IO Board – CODESYS Compatible, All Channels Isolated ^{CODESYS Forge talk (Post)}
Hi everyone, I'd like to share a new EtherCAT slave I/O board I've developed — the EtherCAT Digital & Analog IO Board by EGEROBOTICS. Key specs: 12x isolated digital outputs (24VDC) 12x isolated digital inputs (24VDC) 4x isolated 0–10V analog outputs (12-bit DAC) 4x isolated 0–10V analog inputs (12-bit ADC) All channels galvanically isolated 24VDC powered EtherCAT CoE protocol Typical use cases: Analog servo drive speed reference (0–10V) via EtherCAT Frequency inverter reference signal Proportional valve control Industrial sensor data acquisition Compatible with CODESYS SoftMotion, Beckhoff TwinCAT 2/3, LinuxCNC + EtherCAT HAL, and SOEM. Here's a quick demo video showing it running under CODESYS: 👉 https://www.youtube.com/watch?v=bUuo9reK29s ESI file, PDF manual and AutoCAD drawings available. Available on Tindie: https://www.tindie.com/products/emresensoy/ethercat-digan-io/ Happy to answer any technical questions!
Last updated: 2026-06-13

Post by timvh on CPU + EtherCAT redundancy ^{CODESYS Forge talk (Post)}
It works well with two Wago 750-8210's. I helped a few customers setting this up. But it should work with any device which can control EtherCAT I/O, is real-time and has sufficient network interfaces. Two network adapters can be used to create a redundant EtherCAT network (you need 2 additional switches for this). The other network adapters can be used to interconnect the 2 PLC's (synchronization). We noticed that if you exchange variable lists that there could be some issues if you have long lists. So what we did is use a SoftPLC on a server that contains all the settings which continuously sends network packages (GVL sender) and which is received by both PLC's (network receiver). Switching over is done in milliseconds. The bus doesn't notice the change-over. EtherCAT communication works flawlessly.
Last updated: 2026-01-30

Post by steven-schalm on Frustration-Fueled Feedback on Project File Management and Git Integration ^{CODESYS Forge talk (Post)}
Yes, it's very tedious, especially since Codesys 4 is a custom web development... At Rex Automatisierungstechnik GmbH, we've invested a lot of time in the Python interface to enable something like CI/CD, but also to export the code and re-import it after making clean modifications. Also, the fact that a class/function block is just a single file containing all the methods, props, etc. Yes, and right now I’m building my own VS Code extension with a clean LSP (Language Server Protocol) for ST, as well as an st-validator, st-formatter, st-linter, codesysPackage.json, and codesys_modules folder... Best regards, Steven Schalm / Sharok6130
Last updated: 2026-06-11

Post by boiwithproblems on branch_copy(checkout=True) liefert ungültigen Projekt-Handle (0) in CODESYS V3.5 SP22 Patch 3 ^{CODESYS Forge talk (Post)}
Since upgrading from V3.5 SP21 P3 to SP22 P3, this previously working scripted call fails: project, current_branch = project.git.branch_copy(current_branch,new_branch_name,checkout=True) Error: _3S.CoDeSys.Core.Objects.InvalidProjectHandleException Standard Error: The project handle 0 is invalid Workaround: When you do branch copy with checkout=False and then checkout the branch in a seperate line everything works. The issue seems to be that Codesys doesn't give back a proper handle when you do branch_copy with checkout=True. This is mainly so that issue gets noted and resolved in a further Patch and that people with the same issue might have an easier time debugging their scripts. With kind regards Matthias Rudigier
Last updated: 6 days ago

Post by mankh on Legacy IFM CANopen I/O modules with CR710S / CODESYS 3.5 ^{CODESYS Forge talk (Post)}
Hi, I am migrating an existing IFM system from CR0020 + CODESYS 2.3 to CR710S + CODESYS 3.5. The existing CANopen I/O modules are: CR9011 CR2042 CR2011 My questions are: Can these legacy IFM CANopen modules be used as slaves with the CR710S CANopen Master? Can their existing EDS files be imported directly into CODESYS 3.5? Are there any known compatibility issues with the old IFM EDS files, PDO mapping, or startup SDO configuration? Has anyone successfully used these modules with a CR710S? If so, could you share the recommended configuration procedure? The goal is to replace the CR0020 with a CR710S while keeping the existing CANopen I/O modules
Last updated: 3 days ago

Post by martinlithlith on CODESYS Control for Raspberry Pi SL on Raspberry Pi 4b ^{CODESYS Forge talk (Post)}
hi! a quick question - is it possible to run CODESYS Control for Raspberry Pi SL license on a raspberry pi 4b? i know it says all models in the data sheet, but im not sure it the data sheet has been updated seince the MC-processors for pi. best, Martin
Last updated: 2023-09-04

Post by transmin01 on EL6751 Canopen_Manager issue ^{CODESYS Forge talk (Post)}
Hi, I have a Beckhoff EL6751 EtherCAT / CANopen gateway which fails on the Canbus when the CANopen_Manager is added. Currently no devices are connected to the EL6751. If I add a device, I get the same issue. If I add a device and connect the bus, I get the same issue. Is there something I am doing wrong? Regards Trevor
Last updated: 2023-09-12

Post by snhatton on Alarm Management - latched variable represented as Text list ^{CODESYS Forge talk (Post)}
Hi There, For my understanding: are you trying to display the contents of a text list in an alarm message based on the id? For example, you could maintain a text list of common alarm messages, and then display based on which message is true?
Last updated: 2023-09-18

Sort by relevance or date