Post by marcolim on Slow modbus digital input response ^{CODESYS Forge talk (Post)}
Hi francoinf, I've the similar problem and similar configuration. I did with an Arduino Board loaded by a ModbusRTUServer application on it. What I've notice is the slowly acquisition when release the digital signal (e.g. pin2) when it gets off. Anyone have suggestion?! Thanks
Last updated: 2024-04-13

Post by marcolim on Slow modbus digital input response ^{CODESYS Forge talk (Post)}
[Update]. My issue's solved, I applied the resistors in Pull-down configuration on each digital input. In thus configuration never happened "floating or delaying" acquisition on SoftPLC/Arduino Board.
Last updated: 2024-04-15

Post by ahuckphin on Issues with Modbus Slave with Raspberry Pi ^{CODESYS Forge talk (Post)}
I have a DFRobot RS485 temperature & humidity sensor (SEN0438) connected to my Raspberry Pi via a USB to RS485 adapter. I am able to connect and read the sensor data when running a python code locally. However in Codesys, I encounter this error "A bus error has occurred." and "There was no response in time". Could this be because of Modbus Server Channel and Modbus Server Init configuration on my part? Admittedly I am new to Codesys. To get to this stage, I: 1. added some lines to CODESYSControl_User.cfg 2. added "Modbus_COM" in Codesys and set "Serial Port Configuration" under "General" 3. added "Modbus_Master_COM_Port" in Codesys and checked transmission mode is set to "RTU" 4. added "Modbus_Slave_COM_Port" in Codesys and checked server address is set to 1 (also set 1 in my sensor) 5. added 1 channel and 1 init for "Modbus_Slave_COM_Port" under "Modbus Server Channel" and "Modbus Server Init"
Last updated: 2024-07-10

Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Post by jp23 on Unable to Connect to Modbus RTU Device ^{CODESYS Forge talk (Post)}
Hi all, I am attempting to use the Control Win V3 soft PLC to control a WAGO 750-315 remote I/O system via modbus RTU communication. I am struggling to connect to the device. I have been following this tutorial: https://www.youtube.com/watch?v=YlRfkESaNds I have setup my devices as shown in the images below. I have verified that my com port settings are correct as I am able to connect/control using modbus simulator software with these settings. I have also connected to a modbus master simulator program as instructed in the video, but the orange triangles will not go away. Additionally, I have updated my settings to 485 using the PLC shell. I have also set "always update variables" to enabled (1). Serial port, PCI-Bus, and modbus serial device status all show as "Not Running."
Last updated: 2024-08-26

Master&Slave Program in 4 Axis CNC Project ^{CODESYS Forge talk (Thread)}
Master&Slave Program in 4 Axis CNC Project
Last updated: 2023-10-01

Failure to set the Ethercat slave in boot mode ^{CODESYS Forge talk (Thread)}
Failure to set the Ethercat slave in boot mode
Last updated: 2020-09-15

Write of address to slave not succesfull ^{CODESYS Forge talk (Thread)}
Write of address to slave not succesfull
Last updated: 2020-02-11

Raspberry PI profinet slave not reachable at TIA Portal ^{CODESYS Forge talk (Thread)}
Raspberry PI profinet slave not reachable at TIA Portal
Last updated: 2021-04-21

Codesys Soft SPS als EtherCAT Slave nutzen ^{CODESYS Forge talk (Thread)}
Codesys Soft SPS als EtherCAT Slave nutzen
Last updated: 2017-11-22

Playing with slave in CAM or Geared Axis ^{CODESYS Forge talk (Thread)}
Playing with slave in CAM or Geared Axis
Last updated: 2022-11-14

SDO Read Causes Slave PLC To Reset ^{CODESYS Forge talk (Thread)}
SDO Read Causes Slave PLC To Reset
Last updated: 2015-02-25

Raspberry Pi Profinet Communication between Master/Slave ^{CODESYS Forge talk (Thread)}
Raspberry Pi Profinet Communication between Master/Slave
Last updated: 2021-10-16

Beckhoff DeviceNet Slave EL6752-0010 via Ethercat Coupler EK1100 ^{CODESYS Forge talk (Thread)}
Beckhoff DeviceNet Slave EL6752-0010 via Ethercat Coupler EK1100
Last updated: 2016-12-23

Codesys Profinet Slave detected but no connection ^{CODESYS Forge talk (Thread)}
Codesys Profinet Slave detected but no connection
Last updated: 2021-09-06

Two Servo Master/Slave, Mechanically linked tunning ^{CODESYS Forge talk (Thread)}
Two Servo Master/Slave, Mechanically linked tunning
Last updated: 2017-02-14

Problem with EtherCAT slave restart or all network restart. ^{CODESYS Forge talk (Thread)}
Problem with EtherCAT slave restart or all network restart.
Last updated: 2017-08-09

cerate and add a submodule for a PN slave ^{CODESYS Forge talk (Thread)}
cerate and add a submodule for a PN slave
Last updated: 2017-03-06

FB for I/O Channel and CANopen Slave ^{CODESYS Forge talk (Thread)}
FB for I/O Channel and CANopen Slave
Last updated: 2020-03-11

How to add/Scan devicenet Master/Slave ^{CODESYS Forge talk (Thread)}
How to add/Scan devicenet Master/Slave
Last updated: 2021-03-18

Sort by relevance or date