Post by struccc on Problem Reading Registers via Modbus from non Codesys device ^{CODESYS Forge talk (Post)}
Hi, Might be a good idea first to try out the connection and the device with some handy software, like Modbus Poll. There you can see better, what's really going on... - Is it really connected? - What error code does it return? - Can it read from the register address? - Maybe try Input registers and Holding Registers - can make a difference - Sometimes register addresses are messed up: shifted +-1 (mixing of 2 standards) - Sometimes register addresses start with offset 30000, 40000 ... - Are you using the right protocol? - Is it RTU or TCP? Maybe ASCII? - Can even have a look at the data packets, etc... All this is easier to figure out first with some modbus utility... and then to set it up in CODESYS should not be an issue. P.
Last updated: 2025-03-09

Post by elsmart on Sequential read and triggering of Modbs RTU channels in application ^{CODESYS Forge talk (Post)}
Hello I need some help understanding how to use Modbus RTU (COM port) in Codesys enviroment. I defined a Modbus Server device (slave) in device tree and added some channels to read from (function 3). Also I set trigering mode to Application. I have a POU in which I want to trigger each channel one after the other something like this (C code for better visualisation): for (int i = 0; i < channelsCount; i++) { triggerChannel(channelsArray[i]); // Start transmission while(channel.xBusy); // Wait for transmission to complete } I have found ModbusChannel function block documentation but examples are scarce. I don't understand how rising edge triggering works. What would be the best solution for achieving sequntial channel triggering? What is the common way to read multiple Modbus channels once every time a specified POU is executed?
Last updated: 2025-05-16

Post by qkkk on Device Scan ^{CODESYS Forge talk (Post)}
Hello all, I have developed a custom I/O driver in CODESYS that communicates via a Unix Domain Socket. In my DeviceDescription.xml, I have set up the following: <scan supported="true"> <scanfbinstance fbname="IOScanDevice"> The goal is to allow the user to scan for connected I/O modules from the CODESYS GUI ("Scan for Devices") and automatically populate the device tree with detected submodules.</scanfbinstance></scan> The function block IOScanDevice is implemented in the driver library and added to the main device's FB instances. However, when I initiate the scan from the GUI, nothing appears to happen the function is not executed. Is there an example project or driver (open source or from CODESYS Forge) that demonstrates a working custom scan implementation?
Last updated: 2025-05-26

Post by timvh on Codesys 3.5.18.60 – Application Loss and Persistent Data Corruption ^{CODESYS Forge talk (Post)}
Which device do you use? Does this have persistent memory (e.g. NVRAM) available? Maybe first ask your PLC vendor about the possibilities and how they advice to use persistent variables? If you have no NVRAM available, CODESYS will store the variables in a file when the device gracefully shuts down. But on an abrupt power failure, this is not possible. If you have no NVRAM and you want to use persistent variables, then consider using a UPS. In this case when the power is lost, the UPS can keep the power on the PLC which then can gracefully shut down. Alternatively use the Persistence Manager to store the variable values in a file e.g. only on change. See: https://content.helpme-codesys.com/en/CODESYS%20Application%20Composer/ac_pm_overview.html
Last updated: 2025-08-26

Post by bruceae on Special Characters ^{CODESYS Forge talk (Post)}
Hello, I am fairly new to the codesys environment. Is there a reference chart that I can look at in order to write special character in a string? The Special characters that I need to inclue inside the string are as follows; Null Bell Carriage Return I have a TCP_Write command that I am sending to an external device. In order for that device to function properly it needs to see the string with the null and bell characters as the header, followed by the desired command, terminated with the carriage return. Any reference sheet or how to write this in the actual string would be greatly appreciated.
Last updated: 2025-08-26

Post by pernockham on Control for linux SL, 4.14.0.0 -> 4.15.0.0 breaks web page access. URL requires authentication ^{CODESYS Forge talk (Post)}
I have a problem which I have identified with a device-update from 4.14.0.0 to (4.15.0.0-4.17.0.0) where the newer versions will stop any local access to the internal web page with the browser responding "The requested URL requires authentication". Setting the device back to 4.14.0.0. the web page will respond. Access to web page through Automation server is possible also for the newer version, but not "local" access. Runtime (Codesys control for linux SL) is on 4.17.0.0. I have tried to manipulate settings for 'Access-Control-Allow-Origin' '*' always; through nginx (normally a proxy_pass to localhost:8080). Also tested bypassing nginx by accessing 8080 directly with the same result.
Last updated: 2025-09-08

Post by valenting on Runtime not working on raspberry pi Bullseye ^{CODESYS Forge talk (Post)}
Hello I have a problem with Codesys on Raspberry pi with Bullseye The device is not recognized as a Raspberry pi, as I get this error : ooops... this runtime was built for RASPBERRYPI. Hardware version or firmware version not supported! (-18, 0x00000BB8, 0xFFFFFFFB) I'm running Codesys on a compute module 4S with Raspbian GNU/Linux 11 (bullseye), my kernel version is Linux 5.10.90-v7l+ Codesys version is the latest, released last week (4.11.0.0, CODESYS Control V3.5.19.61 for ARM-32Bit - build Feb 22 2024) I know it works on the same device if I use Raspbian 10 (Buster) with Linux 5.4.81-v7l+ kernel, but for some other reasons I have to use Bullseye. What can I do ?
Last updated: 2024-03-01

Post by dhumphries on Not able to see input data coming from eip adapter on codesys ^{CODESYS Forge talk (Post)}
Does the device have a green icon next to it when the PLC is running? If not you have some kind of communication problem, wireshark may be picking up some data but the scanner may not be configured correctly to receive the data. Check the T>O and O>T bytes and make sure they match on both the scanner and adapter. I've had very little success loading a .eds file and having the configuration work without some manual configuration. If you have a green icon, have you enabled the device to always update variables?
Last updated: 2024-03-02

Post by timvh on Version management ^{CODESYS Forge talk (Post)}
This depends on what you want to achieve with installing the latest version and how you manage your projects and repositories. Maybe you also want to update your device (right click on it to update) or maybe your device is depending on certain versions of libraries (go to the library manager in your project and download the missing libraries). An option is also to first create a projectarchive of the current project you have before you install a new version of CODESYS. Then you can open this projectarchive in the new CODESYS version. Especially if you install the latest version of CODESYS in a Sandbox.
Last updated: 2025-12-15

Post by wbj0t on connect IDE to plc that uses modem ppp ^{CODESYS Forge talk (Post)}
Hello everyone! I have an PLC device that uses modem ppp connection to the internet with white IP. Device PPP connection with modem operator established, so I can connect to this device via SSH also within Codesys IDE (check version, info, etc...) BUT, I cant establish connection to this device in the device gateway options for application upload and debugging. How can I do this? Im trying set my device remote IP and port 11740, but, as I understand, it is wrong decision, because the next logic in this connection: local W10 service (Codesys Gateway) listen on 1217, then (some how) this service scanning local networks for seeking any local IP which listening on port 11740, and then connects and writes there. OR IM WRONG?:) W10 tool 'Test-NetConnection' with parameters 'ip -Port 11740' succeeded with True. Need some help, please :)
Last updated: 2024-05-21

Post by transmin01 on CANbus issue ^{CODESYS Forge talk (Post)}
Update: This initial issue was when using a Linux target PLC. Since then I have created a Win10 target PC and the Codesys software reported an issue associated with the device version (see attached). I am assuming this is an incompatibility with the xml file from the manufacturer and the firmware version on the module and I am chasing this up with Beckhoff. Question is, why would this not report with a Linux target?
Last updated: 2023-09-14

Post by fred on Rasperry Control Debian 12 ^{CODESYS Forge talk (Post)}
Hi, I have Proxmox running on a Rasperry 4 and have debian 12 ARM installed here. I wanted to install Codesys Control for Raspberry on it. According to the messages, the runtime environment and the gateway were installed successfully, but I can't find a device to downplay a program. The sudo service codesys start command fails. (see image) Does somebody has any idea? Thank you for your help! Greetings Fred
Last updated: 2023-11-22

Post by trprsmn on "Scan Network" doesn't find CR1140 device (ifm) ^{CODESYS Forge talk (Post)}
Hi, I'm watching an ifm tutorial on how to setup an industrial controller in CODESYS. I'm using an 'ecomatDisplay43inch_64bit) controller. CODESYS Gateway and PLC are both runngin (systray). However if I click "Scan Network" I can't find my controller. The only thing it finds is a "desktop" it seems (I'm using a Windows 10 on a Mac Book using VMWare, so maybe it has something to do with that?). How can I fix this? Thanks in advance!
Last updated: 2024-09-11

Post by andre-luis on Device diagnosis ( EtherCAT IO card ) ^{CODESYS Forge talk (Post)}
Hi, In our project, it is not rare to have I/O cards issues. I wanted to have a way to check their statuses ( Eg. INIT, OP, PREOP, etc.. ) I was trying to use the GetDeviceDiagnosisInfo method from the IoConfig_Globals, but there is no info available on the Web with a simple example; does someone have a link to some tutorial or anything else ? Kind Regards, Andre.
Last updated: 2025-02-06

Post by marks on Siemens G120X via Ethernet/IP ^{CODESYS Forge talk (Post)}
The goal is to control a Siemens G120X VFD via Ethernet/IP. The .eds is installed into the device repository. The VFD is added and is using the connection and assemblies from the eds. It appears to reach the VFD but fails to establish a connection. The status message is: Diag String: 'Adapter configured. Open all connections.' The PLC is a raspberry pi 4, running codesys target version 4.13.0.0. The development environment is CODESYS V3.5 SP21 + (64-bit). Anyone have experience with this combination? Alternately, where should I look next? Thank you, Mark
Last updated: 2025-05-06

Post by reinier-geers on CAnopen stack ^{CODESYS Forge talk (Post)}
Ive got a project with 6 devices . Version 3.5.9.2 Now i change one to a other device 3.5.20.40 So i update the project to V3.5.20.4 Now i have a lot off faults in the canopendevices . Somehowe the first has no problem and seems that the canopenstackts stays in V3.5.9.2 the others in V4.2.0.0 But i cant put it back to 3.5.9.2 WHY ? And how can now witch one i can update and witch one not ?
Last updated: 2025-09-22

Post by reinier-geers on CAnopen stack ^{CODESYS Forge talk (Post)}
Ive got a project with 6 devices . Version 3.5.9.2 Now i change one to a other device 3.5.20.40 So i update the project to V3.5.20.4 Now i have a lot off faults in the canopendevices . Somehowe the first has no problem and seems that the canopenstackts stays in V3.5.9.2 the others in V4.2.0.0 But i cant put it back to 3.5.9.2 WHY ? And how can now witch one i can update and witch one not ?
Last updated: 2025-09-22

Post by spiessli on Softmotion axis to CANopen Maxon IDX drive ^{CODESYS Forge talk (Post)}
Thanks for the advise, indeed, this was somewhat, what my intention was. I tried around again with EDSes and DCFs, anyway. It appears that the DCFs end up in a subfolder in the attach device dialog. Astonishingly, when attaching the DCF version I get a device in the device tree, where I can add a SoftMotion axis, whereas when I attach the device not in the subfolder, then I cannot. Further astonishingly, when looking in the CANopen parameters in supported profiles, "402" is listed in the case of the DCF variant, whereas in the EDS variant "0" is shown. Comparing EDS and DCF files I cannot guess, where the difference is coming from. I cannot tell either why I have always attached the EDS variant and apparantly never the DCF variant. As I am not in the lab right now, I cannot test if the connection actually is working. Thanks again, spiessli
Last updated: 2024-01-07

Post by shabroz-gill on Unable to load boot application on ARMv7 device restart ^{CODESYS Forge talk (Post)}
I download an application to an ARMv7 32 bit device. I start the applicatin and it all works fine. But when i restart the device the boot app is not able to start. I have to redownload the application from the development environment to get to run again. I get the following error messages in the log on the restart
Last updated: 2023-11-30

Post by cakar16 on Looking for BL20-PG-EN-V3, V3.5.11.20 Device Driver ^{CODESYS Forge talk (Post)}
Hi Everyone, I am Karnadi I am looking for device driver for the following Turk devices and version: - BL20-PG-EN-V3, V3.5.11.20 (Turk) - BL20-2RFID-S, V1.1.3.0 (Turk) - BL20-1RS485/422, V1.1.3.0 (Turk) - BL20-4DO-24VDC-0.5A-P, V1.1.3.0 (Turk) - Ethernet, 3.5.11.20 (Turk) Appreciate if anyone of you can share the device driver (config package) above Thanks and Regards Karnadi
Last updated: 2024-10-04

Post by martinlithlith on Device User Logon and No device is responding.. Pi4b codesys 3.5 SP19 2 + (64-bit) ^{CODESYS Forge talk (Post)}
Hi! Im slowly starting to loose it and i need som help! After a few night of reading up and testing i´m still stuck as a rock and you guys and girls are my last resort for this project. Basic facts; Win 11 Codesys 3.5 SP19 2 + (64-bit) Raspberry pi 4 model b 2 gb Raspian release 11 aarch64 What keeps me up late at night; Username and Password when trying to connect to device and device only beeing connectable for a few seconds. Some of the things I have tried; Username and passord; Credientials from the raspberry Administrator Administrator admin admin Admin Admin administrator administrator Usernames and passwords that I sometimes use (this was a longshot i know, but i was running out of ideas and energy). :) Epand filesystem, activating i2c, spi, 1-wire I can start the gateway and start the runtime. I cant install the edgearm64, arm64 runtime package eventhough I guess i should, i get code [ERROR] Error output: dpkg: error processing archive /tmp/codesysedge_edgearm64_4.8.0.0_arm64.deb (--install): [ERROR] Error output: package architecture (arm64) does not match system (armhf) [ERROR] Error output: Errors were encountered while processing: [ERROR] Error output: /tmp/codesysedge_edgearm64_4.8.0.0_arm64.deb code as a respons. I have tried to Reset Origin Device - no change. I have tried to remove the /etc/CODESYSControl_User.cfg [CmpUserMgr] but i could not find it and i was not sure if i should add it instead but i did not want to mess somthing up. I have tried to create a second gateway with the specific ip if the pi, that did not help. Could it be that i´m currently connected to the pi through WIFI? I can ping the pi and I can connect and control it through VNC. When i scan to select gateway target (scan edge gateway) i find 17-21 devices but can find the pi throug the mac adress. I started of trying to use the "CODESYS Control for Raspberry Pi SL" (I have a license sience earlier) as i read somewhere that this could be used on a Pi4 as well but now i´m trying with the MC SL, no changes, same problem. Right now - gateway version 4.8.0.0 (edgearmHF, armhf), Runtime Package 4.5.0.0 (raspberry, armhf). Any sugestions are very welcome! As mentioned above, theese are some of the things that i have tried/done - but i have been going at this for a while. Best, Martin
Last updated: 2023-09-10

Post by laazik2 on v3.5 SP19 - Modbus TCP Devices - Channel Limit? ^{CODESYS Forge talk (Post)}
I am actually wondering as well if there are plans to fix it or not? As adding two modbus devices creates it's own problems with connection limits and other issues, which some slave devices have.
Last updated: 2023-09-05

Post by t-roger on Ethercat hardware connection and scanning ^{CODESYS Forge talk (Post)}
Hi, I tried to connect me in the codesys runtime after adding Ethercat master but I have this error. What can I tried to resolve that? Br
Last updated: 2025-03-04

Post by fabiodasilveira on PLC Shell commands via ST Code ^{CODESYS Forge talk (Post)}
Thank you, Bingo. Your idea of adding the change to the start up process works. However, I am still intrigued with the fact that SysSockSetIPAddress(strEthernetPort:= '0', strIPAddress:= '192.168.2.12') is different from PLC Shell (setipaddr 0 192.168.2.12).:-(
Last updated: 2025-03-04

Post by tk096 on Cam Editor And Cam Problem ^{CODESYS Forge talk (Post)}
Hi, in the XYVA compile format the editor is adding an additional point if the derivatives are jumping at this point. However, this should not change the path?
Last updated: 2025-06-30

Sort by relevance or date