Post by thysonfury on OPTO22 Groov Epic PR2 Modbus Comms Dropping out every 2 hours and 4 Mins ^{CODESYS Forge talk (Post)}
Hi after some assistance with an error on a Groov PR2 PLC. We have a few different communications set up as shown below: One Modbus TCP Slave Connection - ( Sending / Receiving Data from a PC ) Two Modbus TCP Master Connection - ( Reading Data from a UPS Panel and Reading Data Gas Chromatograph) One Modbus RTU Slave Connection 485 - (Reading Data from a fire and gas panel) One Modbus RTU Master Connection 485 - (Sending Data to a Telemetry Unit) All Licenses have been installed as per OPTO22 suggestions of the order below: Modbus TCP Master Modbus TCP Slave Modbus RTU Master Modbus RTU Slave When I check on License manager the RTU Master license seems to disappear on installing the RTU. (What ever reason I’ve been told this is “normal”). If I use Device License Read It will successfully read all the licenses correctly. Now the issue is every 2 hours and between 4. For what ever reason the communications seems to end and lock up for about 20 seconds. During this time even if I was logged into the PLC it would kick me off and I’d have to re type the password to enter. Most of the devices can handle this however the RTU flags up a communications failure at the SCADA and is raising alarms every 2 hours and 4 mins. We’ve had multiple people go through the code to check for anything obvious. Does anyone have any ideas?
Last updated: 2024-04-15

Post by yannickasselin on Lenze i950 Servo and WAGO PFC200 ^{CODESYS Forge talk (Post)}
I don't have time to go through the whole manual but as I said earlier, the servo drive does not support any of the modes needed for SoftMotion Light to work. If you want to use the full SoftMotion, you could use SMC_Homing function block to do the homing. This function block does not use the Homing Mode. It still uses the CSP mode and does the logic in Codesys runtime instead of in the servo drive. Read the documentation about it to see if it fits your needs. But if your controller only supports SoftMotion Light, I am afraid you will not be able to use the i950. I do a lot of motion stuff with different servo brands. Some support all the modes needed for SoftMotion Light and some don't. You really need to make sure the modes are supported before choosing a brand over another. I tend not to use brand specific controllers in order not to be limited by their supported features. I usually choose a PC (Linux or Windows) and install the Codesys runtime and licences myself. This is the most flexible way to use Codesys in my opinion. Depending on how many axes are needed in your project, a full SoftMotion license may not be more expensive than SoftMotion Light because SoftMotion is available as Application based license whereas SoftMotion Light is not. But of course, SoftMotion is harder on the CPU than SoftMotion Light.
Last updated: 2026-02-13

Post by fajean on Issue with library updates ^{CODESYS Forge talk (Post)}
We make heavy use of internally developed libraries, which are often nested on multiple levels. I routinely work simultaneously on several libraries along with a project that use them. I make changes to a library and immediately perform a download (online or otherwise) in the project. For the longest time, we had zero issue with this. But starting a good while back, with 3.5 SP19 I think, CODESYS started not noticing library updates in other instances most of the time. When the update is missed, the project sees no need to update the code, and any download ignores the new code. A "Clean all" does not solve the issue. But if I close and then re-open the project, then the new version is noticed and the download works. The other solution is saving the library to the registry multiple times (say, 20-30 times, less if lucky), and then at some point the project notices the changed library. I am now on SP21, and it is still not fixed. This is driving me mad, any tasks probably takes me double the time or more due to this problem. My colleague has the same problem on a separate computer. Is this a known issue? Is there a setting somewhere that changes how updates are checked? Thanks for any help!
Last updated: 2026-02-13

Post by damian177 on RPi, Codesys , RS232 ^{CODESYS Forge talk (Post)}
Hi, so far I have only used one com port - built-in interface in RPi - RS232 (dev/serial0) as COM1 in Codesys, and my CODESYControl_User.cfg have congiuration like below: [SysCom] Linux.Devicefile=/dev/serial portnum := COM.SysCom.SYS_COMPORT1 Actually I added to my Rpi Hat with 2xRS232 (SPI). - /dev/spidev0.0 and /dev/spidev0.1 How I should change my CODESYControl_User.cfg file to use added porta as COM2 and COM3 in Codesys ?
Last updated: 2023-10-05

Post by marks on Regarding trend storage access error ^{CODESYS Forge talk (Post)}
I had this problem when running the application as a Simulation. When I wrote it to the Pi all worked as expected. If this isn't the case for you, we've seen some issues with sqlite on the Pi's - so reset Origin and re-download may help in that case. Good luck, Mark
Last updated: 2024-07-24

Post by gseidel on Strange problem with the ‘MC_SetPosition’ function ^{CODESYS Forge talk (Post)}
Hi Gustavo, can you reduce the problem to a project that reproduces the issue without the real servo drives? (You could set the servo drives to virtual and strip away as much as possible from the application.) If you can attach a project, we will have a look. Best regards, Georg
Last updated: 2025-01-10

Post by s1ack on Wago PFC200 Ethernet / IoDrvEthernet Issue? ^{CODESYS Forge talk (Post)}
I changed the interfaces to br0 & br1 as they are designated on the Wago PFC200. That issue is resoved. However, on site I have very high system cpu usage, system as in Linux. Presently it is not known why - my bench system does not exhibit such high system usage. In the past this was due to IGMP network traffic every 250uSec from synchronized inverters.
Last updated: 2025-01-22

Post by atone on Change IO-Link Device Interface connected to a Profinet-Slave at Runtime ^{CODESYS Forge talk (Post)}
OK, I figured out that I can simply define all the sensors as 16 bytes IN/OUT, even if they are not all used. EDIT: The negative effect is that each bit is taken into account as an I/O for the license, even if not used.
Last updated: 2025-04-28

Post by antonz on CoDeSys v3.5: creating libraries for both 32-bit and 64-bit controllers ^{CODESYS Forge talk (Post)}
Thanks Tim. I would think it somehow is relevant when creating a compiled library, but that may very well not be the case. If I understand you correctly, then the same compiled library created from my source code would work for both 32 bit as well as 64 bit controllers.
Last updated: 2025-09-01

Post by onstage on Unable to add EL6751 to Control RTE V3 on W11 IoT LTSC using Eng. V3.5 SP21 ^{CODESYS Forge talk (Post)}
I have working EtherCAT since it can be scanned for slaves, but then I'm stuck getting the information that the device isn't found in the repo. As far as I can see both revisions does however exist in the device repo. Component added in the Configfile. Anyone with some similar experiences?
Last updated: 2025-09-04

Post by tvm on Cannot pass array of constant size to a function as a reference ^{CODESYS Forge talk (Post)}
maybe this would be a better approach, then you don't have to pass the constant at all. FUNCTION fun : INT VAR_IN_OUT arr: ARRAY[*] OF INT; END_VAR VAR lower: DINT; upper: DINT; END_VAR lower:= LOWER_BOUND(arr, 1); upper:= UPPER_BOUND(arr, 1); see here as well https://help.codesys.com/api-content/2/codesys/3.5.12.0/en/_cds_datatype_array/
Last updated: 2024-01-08

Post by lgeertsema on Checkbox font color in visualization style ^{CODESYS Forge talk (Post)}
Hello, I'm having a similar issue with buttons. I want to be able to set the default color and transparency of a button. I've tried a lot of different iterations like KNewman, but to no avail. Has there been some documentation released since KNewman posted this, or is the style editor still as undocumented as ever?
Last updated: 2024-01-11

Post by eschwellinger on New Ladder Diagram conversion does not work due to missing features ^{CODESYS Forge talk (Post)}
The "remove unused" parameters have been added to 1.0 version as well as the "manual" removal of pins... also allowed "empty" inputs for blocks is in and the compile error described there should no longer occurs. Drag drop of variables is not yet implemented and I don't think the double-click feature yet either.
Last updated: 2024-01-29

Post by ronaldcom-pac on Gif in WebVisu ^{CODESYS Forge talk (Post)}
I am looking for some help with using Gifs in the WebVisu of codesys 3.5.18.40 as the model we tried with ladder logic does not animate the Gif and leaves as the first image of the Gif. Is there a way for ST or LL for it to be animated?
Last updated: 2024-02-08

Post by namwind on Wago 8210 ^{CODESYS Forge talk (Post)}
Hi guys, I ran into problem with the controller is not saving the project into the internal memory. I was able to download the project to the controller, but as soon as I try to recycle the power it power back up with no project. I have not ran into this problem before. Please help me out thank you.
Last updated: 2024-03-02

Post by stuartjr on Disabling forcing of specific variables ^{CODESYS Forge talk (Post)}
So I think I've found a way to do what I want, but its a not as simple as I thought it would be. Essentially I've got to put my "logic" that decides what the GVL variable should be at the start of every task (rung 1). Then regardless of what the force is the variable will be set to what the logic decides.
Last updated: 2024-03-15

Post by felipemsgarcia on Generic EtherCAT slave ^{CODESYS Forge talk (Post)}
Hello Edwin, Thank you foryour answer but, I believe I was not very clear in my question, sorry. What I wanted to know is if there is a generic EtherCAT slave object already in CODESYS that I can use for anything, remote IO, Drives, VFD's and so on, as long as I match PDO's. Is there such an object? Thank you again!
Last updated: 2024-05-16

Post by pharus on Setup problems with PiXtend ^{CODESYS Forge talk (Post)}
Hello all, I have an PiXtend V2L complete kit and installed everything like in the manual. Ive installed Codesys V3.5 S20 Codesys Control for Raspberry Pi PiXtend_V2_Professional_for_CODESYS.package But as soon as i Create a Project, i get a lot of error messages, and i cant find the PLC via Ethernet Thanks a lot
Last updated: 2024-06-19

Post by pharus on Setup problems with PiXtend ^{CODESYS Forge talk (Post)}
Hello all, I have an PiXtend V2L complete kit and installed everything like in the manual. Ive installed Codesys V3.5 S20 Codesys Control for Raspberry Pi PiXtend_V2_Professional_for_CODESYS.package But as soon as i Create a Project, i get a lot of error messages, and i cant find the PLC via Ethernet Thanks a lot
Last updated: 2024-06-19

Post by pharus on Setup problems with PiXtend ^{CODESYS Forge talk (Post)}
Hello all, I have an PiXtend V2L complete kit and installed everything like in the manual. Ive installed Codesys V3.5 S20 Codesys Control for Raspberry Pi PiXtend_V2_Professional_for_CODESYS.package But as soon as i Create a Project, i get a lot of error messages, and i cant find the PLC via Ethernet Thanks a lot
Last updated: 2024-06-19

Post by pharus on Setup problems with PiXtend ^{CODESYS Forge talk (Post)}
Hello all, I have an PiXtend V2L complete kit and installed everything like in the manual. Ive installed Codesys V3.5 S20 Codesys Control for Raspberry Pi PiXtend_V2_Professional_for_CODESYS.package But as soon as i Create a Project, i get a lot of error messages, and i cant find the PLC via Ethernet Thanks a lot
Last updated: 2024-06-19

Post by felipemsgarcia on Generic EtherCAT slave ^{CODESYS Forge talk (Post)}
Hello all, I still couldn't find the answer. I wanted to know is if there is a generic EtherCAT slave object already in CODESYS that I can use for anything, remote IO, Drives, VFD's and so on, as long as I match PDO's. Is there such an object? Thank you!
Last updated: 2024-06-20

Post by kaotic2499 on Upgraded Raspberry 2b to Raspberry 5, Trends Broken? ^{CODESYS Forge talk (Post)}
Is there anyone who can assist me? ill just have to raise this as a bug with codesys otherwise. I see this as the only way foward. ill attempt a fresh install of RPI in the next day or two, but thats all i had previously so 🤷‍♂
Last updated: 2025-10-21

Post by josealb2000 on EL6910 as a PROFIsafe F-Host in Codesys ^{CODESYS Forge talk (Post)}
Interested. I can see the EL6633 Profinet Controller can be added in Codesys to the EK1914 or EK1100, and then ProfiSafe devices can be added as the F-DI8/F-DQ3 ET200eco PN. Im unsure how to configure the telegram to the EL6910. Have you been able to make this configuration? EL6910 Manual shows a way but only using TwinSafe.
Last updated: 2025-10-23

Post by eschwellinger on Deploy LicenseServer for Linux SL ^{CODESYS Forge talk (Post)}
As I see from your logs I think the Timeprovider is not accurate enough in your case. Things to check - at the moment you run it on the same device? (for tesing purpose ok) I would set 127.0.0.0 as IP and set it not really to Core 0 ( many other stuff is there)
Last updated: 2025-11-20

Sort by relevance or date