Post by reinier-geers on Raspberry Pi ^{CODESYS Forge talk (Post)}
I Bought a Raspberry Pi licensens. Downloaded the software. Install it on version 19. Start version 19. Whant to set a licensens to the raspberry Pi. Scan the network. But No Raspberry pi. I can Ping the Raspberry Pi. Whats wrong ?
Last updated: 2023-12-28

Post by niallel on How to change bHiresMode ^{CODESYS Forge talk (Post)}
Thank you so much for the reply. The motor is a rotary connected to a linear actuator. So would I set it up as in the attachment screenshot?
Last updated: 2024-03-12

Post by davidbo on What is the prerequisites for a Raspberry Pi to work with SysSockSetIpAddressAndNetMask() ^{CODESYS Forge talk (Post)}
I have done: systemctl stop dhcpcd sudo ip addr flush dev eth0 sudo ip link set eth0 up but a call to SysSockSetIpAddressAndNetMask does not give the eth0 an IP address Why?
Last updated: 2025-11-04

Post by davidbo on What is the prerequisites for a Raspberry Pi to work with SysSockSetIpAddressAndNetMask() ^{CODESYS Forge talk (Post)}
I have now and it works. I had the idea that it had something to do with codesyscontrol.cfg, but where can I find a description of all the things you can set in codesyscontrol.cfg and its syntax?
Last updated: 2025-11-12

Post by trusty-squire on How can you get the active frame index from a frame ^{CODESYS Forge talk (Post)}
If you are switching a frame based on the "Switch Frame Variable", then just use a variable that is accessible to your program to set your active frame. If you're trying to see which is the active visualization, then use the "CurrentVisu" variable. Note you'll need to enable this by checking it on in the Visualization Manager settings. If it's neither of those, you'll need to be more clear on how you're project is set up.
Last updated: 2025-03-11

Post by stdenits on Set several bits in WORD ^{CODESYS Forge talk (Post)}
DEL
Last updated: 2024-04-23

Post by s1mon on Two OneWireMaster on one Raspberry PI 5 ^{CODESYS Forge talk (Post)}
Hi, I want to use two OneWireMaster on a Raspberry Pi5. I'm running Codesys Control for Raspberry Pi 64SL V 4.15.0.0. Under Linux I've configured two GPIOs for 1w bus usage on GPIO4 and GPIO27. Under Linux both masters seem to work fine and I can readout both sensors connected to both GPIOs. The two masters are 'w1_bus_master1' and 'w1_bus_master2'. In Codesys I've configured to OneWireMasters with the corresponding file paths. But in Codesys the 2nd onewiremaster "w1_bus_master2" doesn't work. Status is showing "OnewireMaster : Not running" What am I doing wrong? Does Codesys on Raspberry support multiple OneWireMasters? Any help is appreciated.
Last updated: 2025-06-10

Post by s1mon on Two OneWireMaster on one Raspberry PI 5 ^{CODESYS Forge talk (Post)}
Hi, I want to use two OneWireMaster on a Raspberry Pi5. I'm running Codesys Control for Raspberry Pi 64SL V 4.15.0.0. Under Linux I've configured two GPIOs for 1w bus usage on GPIO4 and GPIO27. Under Linux both masters seem to work fine and I can readout both sensors connected to both GPIOs. The two masters are 'w1_bus_master1' and 'w1_bus_master2'. In Codesys I've configured to OneWireMasters with the corresponding file paths. But in Codesys the 2nd onewiremaster "w1_bus_master2" doesn't work. Status is showing "OnewireMaster : Not running" What am I doing wrong? Does Codesys on Raspberry support multiple OneWireMasters? Any help is appreciated.
Last updated: 2025-06-10

Post by ac-spr on Runtime variable that indicates a user is online to the code ^{CODESYS Forge talk (Post)}
Looking to access a variable at runtime that indicates a user is online to the code. essentially want to use this value to feedback to the user on the HMI. we use turck and bosch rexroth devices if this information helps. I was hoping there was a variable at the application level, or a library that could be used but I was unable to find anything. I know there's a pop up when you try to login/ go online to the code when a user is already logged in, so the system does provide an indication that it knows already online, but has no access to a value from what I can see. Any help is appreciated
Last updated: 2024-04-22

Post by mubeta on Reset problem with CMZ SD/SVM drive ^{CODESYS Forge talk (Post)}
In a recent project with SoftMotion 4.15.0.0, where I integrated two SD drives from CMZ (from catalogue EDS and not imported), on CANopen bus, I found that the SoftMotion MC_Reset function does not reset the drive faults. Even if the drive is in fault, either on the device or on the drive at the CoDeSys level, the function does not reset, instead reporting the error code: no error to reset. Finally, I had to connect the reset bit of the ControlWord directly to a tag in my program. Something I never had to do on other drives: Lexium, etc. all reset simply with MC_Reset.
Last updated: 2024-07-24

Post by alimans on OPC-UA Server, Symbol Set: Raise an error: Object reference not set to an instance of an object. ^{CODESYS Forge talk (Post)}
Hi everyone, I just created a very simple library without any code and, added it to my very simple project. after adding this library, I get an error when I try to open "Symbol Set" in "OPC UA Server" in "Communication Manager". Here is the code of my POU in the library: FUNCTION_BLOCK POU VAR eCommand : (CMD_NONE:=0, CMD_RESET:=-1) INT := CMD_NONE; END_VAR Attached is the error that I get. I also noticed that by removing the enumeration variable above (eCommand), I can open the "Symbol Set" again. Anybody has any idea why this error is raised and how could I use enumeration variables without error in "OPC UA Symbol Set"?
Last updated: 2024-08-08

Post by dkugler on Project loses 'Download time' information ^{CODESYS Forge talk (Post)}
and if you copy or transfer a project to another place, copy not only the .project, copy .compileinfo .bootinfo and .bootinfo_guids then we figured out it is more often possible to go online without full download. If you build an archiv and extract it, some of this files are missing and login isn't possible without download. I work with V3.5 SP16 Patch 4. I don't know if this problem of the archiv is solved in newer Versions/SP's and I don't know what the problem of Codesys is to help out a lot of programers of this very annoying problem or at least help with a workaround
Last updated: 2025-09-18

Post by manuknecht on High Cycle Times for SoftMotion_PlanningTask when using AxisGroup ^{CODESYS Forge talk (Post)}
Hello all I am using an AxisGroup with the Gantry2 Kinematics to move a 2D-Gantry system. When creating the AxisGroup, the SoftMotion_PlanningTask is created automatically with a cycle time of 2 ms in my case. I realized that the maximum cycle time of this task can spike to very high values (up to 60 ms) at lower speeds of the motion, leading to synchronization issues and errors on the axes. The same behaviour - though not as drastic - can be observed with virtual axes too. Is this behaviour intended or to be expected? Can the cycle time or type of the SoftMotion_PlanningTask be changed to prevent these errors? Or is there another fix for this issue? I tried changing the cycle type to Freewheeling, which solved the synchronization issues, but caused an error on the AxisGroup after a while, reading SMC_CP_QUEUE_UNDERRUN. Thanks in advance and best regards Manuel
Last updated: 2024-03-07

Post by jbcregen on Accessing parameters from a structure or function block with the web interface ^{CODESYS Forge talk (Post)}
I have a project with hundreds of OPC-UA variables available on the network. A lot of these variables are used actively in various scripts that run in background in the OS (Linux). I'm experimenting with Automation Server and I have a hard time understanding how the web interface populates its parameters list for a given PLC (<plc details="" parameters="" for="" plc="" 'xyz'="">).</plc> In this page, it looks like the only variables available are the ones that are of a "base" type : bool, TIME, String, INT, etc. All the variables that are nested into function blocks or structures are not available in the web interface, even if they are available to any OPC-UA client. Is this a limitation of the Automation Server or is there something that can be done in Codesys?
Last updated: 2025-12-01

Post by tortilla on J1939 connection between two devices ^{CODESYS Forge talk (Post)}
Hey, I'm pretty new to CoDeSys so I don't know a lot of things yet. I have to create a connection between two devices (CANbus - J1939 connection). The idea for now is to send a message from one to another (one operates on 3.5 SP11 the other one on 2.3) I watched a few videos, worked with the documentation and worked with chatGPT 4o and was able to build the attached file. This part is about the device on 3.5.11: I'm using the J1939LocalECUDiag, TransmitParameterGroup, TransmissionTrigger Function blocks to send the message but my TransmitPG.xBusy / .xDone never turns to True and therefore my message is not sent while TransmitPG.xExcecute is True. I added the two devices in the CANbus in the J1939Manager and addapted the options like I've seen in the documentation. Can anyone explain what's wrong with my code in this casse or give me advices how to properly create a connection between my two devices? Thanks in advance!
Last updated: 2024-05-23

Post by mani-i4point0 on Issue with WebVisu on Raspberry PI ^{CODESYS Forge talk (Post)}
Hi, I am running Codesys Runtime by purchasing 'Codesys control for raspberry pi MC SL', I am trying to use the Variables from my GVL's. Few of the variables used as a Pushbutton form the Visualization. These 'BOOL' Variable getting unlatched automatically even though there is no write function in the Overall project. All of them are 'Read' functions, at the same time few other BOOL variable behaviors are seems to be fine. I have tried, clean all and download, serval time restarted the hardware. Happy to share any any information. Your input to resolve this issue would be highly appriciated. Version Details: codesyscontrol 4.8.0.0, armhf codesyscontrol based on SDK 3.5.19.0
Last updated: 2024-03-20

Post by kareem-pt on Velocity is too low even though correct value is reported ^{CODESYS Forge talk (Post)}
Hello, I'm playing around with a single axis. I've setup scaling and set the drive to move 360 degrees in the commissioning tab. The axis does move 360 degrees, but it moves much slower than the 360 degrees per second that I set for the velocity. It seems to be about 3 times slower (taking about 3 seconds instead of 1). This is despite the set and actual velocity both being displayed as 360. The acceleration, deceleration and jerk are all set to very high values. I'm just running this on my PC, using demo mode (no license purchased yet). I've attached a video showing the problem. Does anyone know what the problem could be? Thanks
Last updated: 2025-06-06

Post by jaspergain on SoftMotion Axes issue ^{CODESYS Forge talk (Post)}
Dear, We have an issue with SoftMotion and it's licensing. We don't use SoftMotion in this project. But a SoftMotion license is required by it. The License metrics tell's us there is a -1 Axes. Is there a way to reset this? Delete this? There was a MotionControl device in the project, but we have deleted this. But it stayed at -1. Thanks for you help.
Last updated: 2024-02-29

Post by gustavocsw on MQTT memory leak problem ^{CODESYS Forge talk (Post)}
Hello everyone, I'm using the IoT Library to implement the MQTT communication with my local broker server in order to publish and subscribe at specifics topics to share and consume information about my application. But, it seems that are occurring some memory leak problem in a "high" frequency (more than 10 Hz) subscribe process. I follow the same method as in IoT Lib exemples, and at first looks perfect but my PLC was rebooting frequently and when I check its memory usage that was increasing as fast as the subscribe massage was sent. I'm using a WEG PLC410 and a WEG PLC500, and this error occurred in both of them (including in CODESYS Control Win x64). The application sends to the system a message JSON with the float payload Ex. {"data" : 0.8500}, but this happens with a INT, or BOL as well. I use the follow code in my application to find the value: //FindFirstValueByKey VARs PROGRAM JSON_VELO VAR //------Setting the JSON Subscriber to Set the Relay Value jsonDataVelo : JSON.JSONData; jsonByteArrayReaderVelo : JSON.JSONByteArrayReader; xST1okVelo : BOOL; FindFirstValueByKeyVelo : JSON.FindFirstValueByKey; jsonElementVelo : JSON.JSONElement; xDoneReaderVelo : BOOL; xDoneFindVelo : BOOL; //STRING and WSTRING for Subscribe the massage sPayloadJsonVelo : STRING := 'opa'; psPayloadJsonVelo : POINTER TO BYTE := ADR(sPayloadJsonVelo); //wsPayloadJsonRelaySet : WSTRING := "opa"; wsPayloadJsonVelo : WSTRING := STRING_TO_WSTRING('opa'); pwsPayloadJsonVelo : POINTER TO WORD := ADR(wsPayloadJsonVelo); lrVelo : LREAL; xKeepAliveVelo : BOOL; xSetVelo : BOOL; RSSet : RS; LIMPAR : STRING; //Find the msg end sFindVelo : STRING := '}'; psFindVelo : POINTER TO STRING := ADR(sFindVelo); iLenVelo : INT; iSizeVelo : INT := 12; udiContMsg : UDINT; END_VAR // FindFirstValueByKey CODE // Relay Set configuration xSetVelo := MQTT_SUBSCRIBER.RSVelo.Q1; IF xSetVelo THEN xKeepAliveVelo := TRUE; END_IF IF xKeepAliveVelo THEN udiContMsg := udiContMsg + 1; iLenVelo := TO_INT(StrLenA(psPayloadJsonVelo)); iSizeVelo := iLenVelo - TO_INT(MQTT_SUBSCRIBER.udiPayloadSizeVelo); StrDeleteA(psPayloadJsonVelo,iSizeVelo,iLenVelo); wsPayloadJsonVelo := STRING_TO_WSTRING(sPayloadJsonVelo); pwsPayloadJsonVelo := ADR(wsPayloadJsonVelo); //MQTT.ConvertUTF8toUTF16(sourceStart:= ADR(sPayloadJsonVelo), targetStart:= ADR(wsPayloadJsonVelo), dwTargetBufferSize:= TAM, bStrictConversion:= 1); //Reset jsonByteArrayReader jsonByteArrayReaderVelo ( xExecute := TRUE, pwData := pwsPayloadJsonVelo, jsonData := jsonDataVelo, xDone => xDoneReaderVelo ); FindFirstValueByKeyVelo( xExecute := xDoneReaderVelo, wsKey := "data", diStartIndex:= 0, jsonData := jsonDataVelo, jsonElement => jsonElementVelo, xDone => xDoneFindVelo ); IF xDoneFindVelo THEN lrVelo := jsonElementVelo.value.lrValue; //Reset jsonByteArrayReader jsonByteArrayReaderVelo ( xExecute := FALSE, pwData := pwsPayloadJsonVelo, jsonData := jsonDataVelo, xDone => xDoneReaderVelo ); FindFirstValueByKeyVelo( xExecute := FALSE, wsKey := "data", diStartIndex:= 1, jsonData := jsonDataVelo, jsonElement => jsonElementVelo, xDone => xDoneFindVelo ); xKeepAliveVelo := FALSE; GVL.xSetVeloRead := TRUE; END_IF END_IF And this to subscribe at the topic: //SUBSCRIBE VAR: //----------------- Subscribe Velocity ----------------------- MQTTSubscribeVelo : MQTT.MQTTSubscribe;//Variable MQTTSubscriber block -X - function-X wsTopicSubscribeVelo : WSTRING(1024) := "CORE/odometry/GET/data/simp"; // Topic to publish a message sSubscribeMassageVelo : STRING; udiPayloadSizeVelo : UDINT; xSDoneVelo : BOOL; xSErrorVelo : BOOL; xReceiveVelo : BOOL; eSTypeVelo : MQTT.MQTT_ERROR; eSMQTTErrorVelo : MQTT.MQTT_ERROR; RSVelo : RS; udiCont : UDINT; //SUBSCRIBE CODE: MQTTSubscribeVelo( xEnable:= MQTT_CLIENT.xConnection_Broker AND NOT xSErrorVelo AND NOT JSON_VELO.xKeepAliveVelo, pbPayload:= JSON_VELO.psPayloadJsonVelo, udiMaxPayloadSize:= SIZEOF(JSON_VELO.sPayloadJsonVelo), udiPayloadSize => udiPayloadSizeVelo, mqttClient:= MQTT_CLIENT.ClientMQTT, wsTopicFilter:=wsTopicSubscribeVelo, xDone => xSDoneVelo, xError=> xSErrorVelo, xReceived => xReceiveVelo, eMQTTError=> eSMQTTErrorVelo ); RSVelo(SET := xReceiveVelo, RESET1 := JSON_VELO.xKeepAliveVelo);
Last updated: 2024-09-09

Post by william-blandon on RecipeManCommands.ReloadRecipes ^{CODESYS Forge talk (Post)}
Hi Dave. Thanks for your answer. I still struggling with this. I have done everything according with the Codesys help even I have looked in detail at the example. I have double checked the recipe manager configuration and the use of all the methods. There are two methods that do not work as expected. I'm using Codesys 3.5.19.20 and recipe management 4.4.0.0 .CreateRecipe just create a recipe in the recipe definition but do not create the file. This have a walk around just giving a .ReadAndSaveRecipe afterwards. .ReloadRecipes do nothing but do not generate any error as well. After calling it I call the .GetRecipeCount and the number is always 0. When I create a new recipe (using the function block methods) then the number changes. Looks like this method is looking to the wrong directory finding nothing. I don't know if there is a missing configuration in the CODESYSControl.cfg file. I'm thinking in a walk around for this but I need to create a strings array with the recipe names as retentive and making all the management when deleting and adding recipes. Have had some one the same problem?
Last updated: 2024-05-23

Post by davidbo on RPI can system operation like rm in a shell have an impact on a Task cycle time ^{CODESYS Forge talk (Post)}
3.5 18 SP2 I think the control is 4.2.0.0. I am not in the office before on Wednesday.
Last updated: 2024-09-23

Post by dangjoris on Missing function for ConfigGetParameterValueBool (SM3RaspiStepper) ^{CODESYS Forge talk (Post)}
Hello, I've been trying to get the SM3RaspiStepper application working for a long time, but the function block with the function ConfigGetParameterValueBool and ConfigGetParameterValueLReal is always missing. Does anyone know how I can get them? I also added a screenshot.
Last updated: 2024-09-30

Post by smartcoco on Recipe Manager - RecipeManCommands, load & write wrong values, Bug? ^{CODESYS Forge talk (Post)}
I have also been troubled by this issue for a long time, to the extent that I have to implement a recipe management library myself. Codesys version used: 3.5.19.40
Last updated: 2023-12-16

Post by eschwellinger on "Distributed clocks are not synchronized, Rea time problem on hardware" ? ^{CODESYS Forge talk (Post)}
use a realtime capable target, not Control Win. Either a realtime patched Linux or Control RTE on Windows.
Last updated: 2024-03-04

Post by tvm on Timer On Vijeo ^{CODESYS Forge talk (Post)}
Vijeo doesn't support TIME variables, so the easiest thing to do is convert to a STRING in your program, and use that variable. You could use TimeAsString:= TIME_TO_STRING(TimeVar) to get a string that looks like this: T#5h10m45s200ms
Last updated: 2024-05-07

Sort by relevance or date