Post by cillian on Error when opening HTML5Control Editor ^{CODESYS Forge talk (Post)}
Hello, I am new to this forum so apologies if this is posted in the incorrect area. I am getting an error when trying to open the HTML5 Control Editor - this was working fine previous days. I am using Codesys V3.5 SP20 Patch 3. I have reinstalled the application. Below is a screenshot of what shows when I attempt to open HTML5 Control Editor. Would anyone know the solution to rectifying this problem? Thanks in advance. Edit: This is now fixed.
Last updated: 2024-10-22

Post by askic on PLC error log help ^{CODESYS Forge talk (Post)}
Hello, I'm using Codesys 3.5.20.0 version and I noticed that even with the most basic standard project create, there are error messages like shown in the acttached picture. The similar questions are already asked here on the CODESYS Forge Talk, but remained unanswered. Exact screenshot is attached, but essentially I would like to know which component in the Codesys has CmpID = 0x00000019 and what this Timeout means?
Last updated: 2025-01-10

Post by respl on IFM EXOR Network variable Error ^{CODESYS Forge talk (Post)}
We are connected IFM CR711S to Exor EX710. We are exchanging data using network variables. Both devices are configured on same project so no need to use file source. When tested application it works fine. But after 3 months same application not working. We are able to send data from CR711 to EX710 but data from Ex710 to CR711s works only for one scan when we cold reset CR 711S. Can somebody help to find out error.
Last updated: 2025-03-17

Post by phryniszak on RPI CANFD ^{CODESYS Forge talk (Post)}
Hi, I have rpi with CANFD MCP2518FD. Classic can communication is working OK but when I try open in CANFD hDriver := CL2.FdDriverOpenH(usiNetId := 0, uiNominalBaudrate := 500, uiDataBaudrate := 0, xSupport29Bits := FALSE, ctMessages := 100, peError := ADR(eError) error is returned with value 10226 which is not documented (https://content.helpme-codesys.com/en/libs/CAA%20Can%20Low%20Level%20Extern/Current/CAN-Low-Level/Enums/ERROR.html#error) CAA CanL2 is 3.5.21 version. Question is: 1. Is anyone get CANFD working? 2. What is meaning of this value (10226)? Regards, Pawel
Last updated: 2025-08-09

Post by phryniszak on RPI CANFD ^{CODESYS Forge talk (Post)}
Hi, I have rpi with CANFD MCP2518FD. Classic can communication is working OK but when I try open in CANFD hDriver := CL2.FdDriverOpenH(usiNetId := 0, uiNominalBaudrate := 500, uiDataBaudrate := 0, xSupport29Bits := FALSE, ctMessages := 100, peError := ADR(eError) error is returned with value 10226 which is not documented (https://content.helpme-codesys.com/en/libs/CAA%20Can%20Low%20Level%20Extern/Current/CAN-Low-Level/Enums/ERROR.html#error) CAA CanL2 is 3.5.21 version. Question is: 1. Is anyone get CANFD working? 2. What is meaning of this value (10226)? Regards, Pawel
Last updated: 2025-08-09

Post by wedahitha on Could not open library 'SysSocket23, ^{CODESYS Forge talk (Post)}
Hi there, I am trying to open a codesys project done by someone else and Once I install all the libraries I get this error [ERROR] : Library Manager [PROJECT 01: PLC Logic: Application]: Could not open library 'SysSocket23, * (System)'. (Reason: The library 'SysSocket23, * (System)' has not been installed to the system.) SysSocket23 is a standard library and I also tried using the same OSCAT library which was from the original computer that made this code. Using CODESYS V3.5 SP18 Patch 2 Please help me how to solve this problem.
Last updated: 2023-12-19

Post by josephbourgeois on Tracking out product ^{CODESYS Forge talk (Post)}
Hi everyone! I synchronize the operation of the tripod and the conveyor. I have a problem with the product tracking algorithm on the conveyor (PCS_1). Sometimes I need to stop tracking a product on command without completing the operation. I do this using MC_GroupStop. But when I need to start moving in WCS again (using fb movelinearabsolute), I get a tripod kinematics error - SMC_CP_INVALID_ORIENTATION (Invalid orientation (non-orthonormal matrix or non-unit quaternion, internal error)). MC_ResetGroup does not help. What could be the problem? Has anyone encountered this?
Last updated: 2024-02-05

Post by josephbourgeois on tracking out product ^{CODESYS Forge talk (Post)}
Hi everyone! I synchronize the operation of the tripod and the conveyor. I have a problem with the product tracking algorithm on the conveyor (PCS_1). Sometimes I need to stop tracking a product on command without completing the operation. I do this using MC_GroupStop. But when I need to start moving in WCS again (using fb movelinearabsolute), I get a tripod kinematics error - SMC_CP_INVALID_ORIENTATION (Invalid orientation (non-orthonormal matrix or non-unit quaternion, internal error)). MC_ResetGroup does not help. What could be the problem? Has anyone encountered this?
Last updated: 2024-02-05

Post by suthesan on Error when I go online on Simulation or PLC ^{CODESYS Forge talk (Post)}
Hello I not sure if I made this topic under the right category. But I have a error, when I try to run a simple code on simulation or PLC. I have also tried to make a fresh project. I am testing the PLC and want to see if there is some way I can make an actuator run. Please help by looking at the picture, Iam stuckd and I don't know how to fix it.
Last updated: 2024-02-07

Post by tvm on VisuFbFrameBase.SetInputPositionData: The element id for the input position cannot be determined ^{CODESYS Forge talk (Post)}
I'm getting this error on one of my projects. Searching for it I came across this https://www.codesys.com/fileadmin/data/Images/System/Releaseinformation/Patch-Note-CODESYS-Visualization-4300.html which says it was a bug VIS-1394, fixed in Visualization 4.3.0.0. I'm using a previous visu version, what is the cause of this error, and what can be done to work around it?
Last updated: 2024-02-08

Post by andy-yemm on Assertion Failed ^{CODESYS Forge talk (Post)}
I had similar assertion failed error messages today. I am fairly new to Codesys. I tried using SFC for the first time, I usually use ST. Anyway I had errors in some of my transitions. I copied and pasted transition code and forgot to change the target of the code. I started getting lots of the assertion errors but now I have sorted out the problems and it compiles OK the assertion error messages seem to have stopped. There do not seem to be any other responses to your post, did you resolve your problem?
Last updated: 2024-03-19

Post by carohe on VisuNamespace != null ^{CODESYS Forge talk (Post)}
Hello, this error occured frequently over the past couple of weeks. I found out, when adding a webvisu, CODESYS added Visu libraries in the library manager. One of the libraries was the "VisuElemsAlarm" library. In my case it added this one with the version 4.3.0.0. However another library that also contained the "VisuElemsAlarm", used the "VisuElemsAlarm" with the version "4.4.0.0". After changing the Version "4.4.0.0" and uninstalling this version, the error has not occured anymore. Regards, carohe
Last updated: 2024-04-02

Post by rabaggett on CODESYS control for Raspberry Pi 64 SL errors ^{CODESYS Forge talk (Post)}
Update: I started over. I saved progress at each step. all compiled zero errors, zero warnings. Pre-processor messages remain, but I can make progress. Until I try to re- load the project file in Codesys. Re-loaded files error as above when compiled, even though they compiled error-free immediately before saving. Is my installation borked? (Not easy to re-install due to IT madness...)
Last updated: 2024-05-03

Post by engrahman on The current baud rate could not be determined in CR0020 IFM with maintenance tool ^{CODESYS Forge talk (Post)}
Hello everyone, im working with IFM CR0020 controller via RS232 protocol where im trying to connect it to my PC but, every time when im using the maintenance tool to identify the device i get the error "The baud rate could not be determined" i have tried to change the cable of RS232 with different types but the error presist, any idea how to fix it
Last updated: 2024-05-21

Post by dario99 on Error when creating a new HTML5 visualisation ^{CODESYS Forge talk (Post)}
Hello, I'm quite new here. I would like to create a new HTML5 visualisation. I have already imported some templates via the visualisation elements repository, this worked fine. However, when I want to open the html5control.html in the editor or create a new project myself, I always get this error: default filesystem storage could not be found. Did you add storages.plugin to the profile? I can't find this plugin. The Package Designer (V4.1.0.0) and Codesys Visualisation (V4.5.0.0) plugins are installed Can anyone help me? Thank you very much!
Last updated: 2024-06-14

Post by youness on CSVReaderInit returns error : INVALID_HANDLE ^{CODESYS Forge talk (Post)}
I have Already the same problem when i'm trying to write data more than 10 times in the same file. In fact, i send my data periodicaly to a file that i configured to have permission of W/R in my CodesysContol.cfg. When the Error occurs, i must reboot my machine to success. It means that the problem isn't realted to a limitation of size, but a problem in the function supposed to handle the file. totorovic : allow me to know if you've found a solution to your problem. Thanks.
Last updated: 2025-11-26

Post by tobiassantos on History of Alarms ^{CODESYS Forge talk (Post)}
I am running tests using the Windows runtime environment. The alarm history is not being logged and displays the error: "Some kind of disk I/O error occurred. Check disk space" in the alarm table. Furthermore, it is not possible to export the alarms. I have already tried to find a configuration field in Alarm storage and Alarm configuration to fix this problem, but I haven't found any related fields.
Last updated: 2026-01-05

Post by tobiassantos on History of Alarms ^{CODESYS Forge talk (Post)}
I am running tests using the Windows runtime environment. The alarm history is not being logged and displays the error: "Some kind of disk I/O error occurred. Check disk space" in the alarm table. Furthermore, it is not possible to export the alarms. I have already tried to find a configuration field in Alarm storage and Alarm configuration to fix this problem, but I haven't found any related fields.
Last updated: 2026-01-05

Post by sheberle on ERROR: Calling the program "AlarmStorage_Prg" is not allowed from multiple tasks ^{CODESYS Forge talk (Post)}
Do you have any additional information about when the error occurs? I am trying to recreate this issue to find a workaround... Maybe you could also make the project available. You could add the following logfilter to the CODESYS configuration file: [CmpLog] Logger.0.Filter=0xFFFFFFFF Logger.0.Enable=1 Logger.0.MaxEntries=10000 Logger.0.MaxFileSize=1000000 SysSem.Filter=0xFFFFFFFF SysTask.Filter=0xFFFFFFFF I hope that the log filter will show us which task is responsible for this, so we can narrow it down a bit more.
Last updated: 2026-03-31

Post by codegunner on how to convert library from CodeSys 2.3 to CodeSys 3.x ? ^{CODESYS Forge talk (Post)}
hello, ive tried everything and keep getting error like i have opened a file in read only so cannot save no idea what is causing it, file is not read only i cannot even open a new file i make with one variable in 2.3, get same error for read only. do you have a 2.3 file you can send me tomtry and open for a test? thanks
Last updated: 2026-04-29

Post by fabiodasilveira on Static Analysis Error SA0026 ^{CODESYS Forge talk (Post)}
Hello Everyone, I am really struggling to understand why codesys would present an error regarding the following: VAR strByte1: STRING(10):= '192'; strByte2: STRING(10):= '168'; strByte3: STRING(10):= '1'; strByte4: STRING(10):= '0'; strIPAddress: STRING:= '192.168.1.1'; END_VAR //Updating Variables strByte1:= BYTE_TO_STRING(GVL.abyPSsIpAddress[0]); strByte2:= BYTE_TO_STRING(GVL.abyPSsIpAddress[1]); strByte3:= BYTE_TO_STRING(GVL.abyPSsIpAddress[2]); strByte4:= BYTE_TO_STRING(GVL.abyPSsIpAddress[3]); strIPAddress:= CONCAT(strByte1, CONCAT('.', CONCAT(strByte2, CONCAT('.', CONCAT(strByte3, CONCAT('.', strByte4)))))); Any help would be much appreciated.
Last updated: 2026-07-27

Post by kunz on Profinet Device keeps abort connection with AR alarm.ind(err) ^{CODESYS Forge talk (Post)}
Can somebody explain what the error Connection aborted: AR alarm.ind(err) exactly mean? I have the same Problem and dont know how to solve the issue
Last updated: 2023-08-21

Post by eschwellinger on CSVReaderInit returns error : INVALID_HANDLE ^{CODESYS Forge talk (Post)}
this is a security issue not to read/write in the plc allowed path I would recommend to update and change the path in the application were the files are😏
Last updated: 2023-08-30

Post by roundex on CSVReaderInit returns error : INVALID_HANDLE ^{CODESYS Forge talk (Post)}
Could you please give me an example where to select new path in plc. Right now my csv files are placed into /home/user/csvfiles
Last updated: 2023-08-30

Post by totorovic on CSVReaderInit returns error : INVALID_HANDLE ^{CODESYS Forge talk (Post)}
Thank you for the return. The path targets to a CFast card. User has R/W access to it. We will try to change it.
Last updated: 2023-08-31

Sort by relevance or date