Post by marekxc on Little endian to Float from Modbus RTU ^{CODESYS Forge talk (Post)}
Maybe try going back to step one and: Var Reg1: WORD; Reg2: WORD; Reg12: DWORD; Value: REAL; end_var // program Reg1:= 4096; Reg2:= 14884; Reg12:= (reg2 * 65536) + reg1; Value:= DWORD_TO_REAL(Reg12);
Last updated: 2023-12-28

Post by dim54 on MBChannel ^{CODESYS Forge talk (Post)}
Hello! I am interested in the Modbus Slave channel parameter uiReadLength to use in the ST-program (see picture). How to read the value of uiReadLength in a ST-program? Only Edwin the Great and Terrible can answer this question.
Last updated: 2024-01-22

Post by timvh on Timeout Error in Modbus Communication with WAGO PFC200 and iEM2050 Meter using 750-652 Module ^{CODESYS Forge talk (Post)}
I'm not sure, but maybe you have to configure the 750-652 first with the WAGO-IO-CHECK software to set it in RS485 mode?
Last updated: 2024-02-27

Post by dawidr on Timeout Error in Modbus Communication with WAGO PFC200 and iEM2050 Meter using 750-652 Module ^{CODESYS Forge talk (Post)}
Did you manage to solve the problem with time out? I got the same issue and I've no idea what I'm doing wrong.
Last updated: 2024-04-07

Post by dawidr on Timeout Error in Modbus Communication with WAGO PFC200 and iEM2050 Meter using 750-652 Module ^{CODESYS Forge talk (Post)}
Did you manage to solve the problem with time out? I got the same issue and I've no idea what I'm doing wrong.
Last updated: 2024-04-07

Post by marcolim on Slow modbus digital input response ^{CODESYS Forge talk (Post)}
Hi francoinf, I've the similar problem and similar configuration. I did with an Arduino Board loaded by a ModbusRTUServer application on it. What I've notice is the slowly acquisition when release the digital signal (e.g. pin2) when it gets off. Anyone have suggestion?! Thanks
Last updated: 2024-04-13

Post by marcolim on Slow modbus digital input response ^{CODESYS Forge talk (Post)}
[Update]. My issue's solved, I applied the resistors in Pull-down configuration on each digital input. In thus configuration never happened "floating or delaying" acquisition on SoftPLC/Arduino Board.
Last updated: 2024-04-15

Post by timvh on IoDrvModbusTCP_Diag not defined when using MODBUS ^{CODESYS Forge talk (Post)}
Most likely related to the Device Diagnostics functionality. Double click on your device (PLC), go to the tab "PLC settings". Enable the advanced option "Enable diagnosis for devices". Build your application again.
Last updated: 2024-04-15

Post by mbmik on IoDrvModbusTCP_Diag not defined when using MODBUS ^{CODESYS Forge talk (Post)}
Thanks alot for your time and help! I quickly tested the suggestion, as it makes a lot of sense. Unfortunately the erros still appear as before. The settings was already set before, and i tried turning it off.. no effect..
Last updated: 2024-04-16

Post by hyet on IoDrvModbusTCP_Diag not defined when using MODBUS ^{CODESYS Forge talk (Post)}
Currently seeing the same issue here, with a project moved from 3.5.19. Diving into it too to see if i can find the cause
Last updated: 2024-05-01

Post by guilhermeleao on How to communicate 2 pcs that are using CODESYS ^{CODESYS Forge talk (Post)}
I need to connect 2 computers on the same network that are running codesys, so that they can receive and change variable values from each other. This connection must preferably be made using Modbus.
Last updated: 2024-05-06

Post by zer0g on Modbus Client Request Not Processed ^{CODESYS Forge talk (Post)}
Hi, I have the same problem as the guys above. Any solution or hint in the right direction is appreciated. Codesys version 3.5.19.2, Lib version: 4.4.0.0. Thank you!
Last updated: 2024-05-29

Post by dantheman on Connecting to SoftPLC Only Works By Turning Off Modbus Ethernet Port ^{CODESYS Forge talk (Post)}
It's all good btw, learned that the runtime doesn't isolate the networks that are involved so changing the ethernet subnets away from the Wi-Fi's subnet was all I needed (maybe some config file changes helped, can't say for certain)
Last updated: 2024-08-08

Post by esmith on OPTO22 Groov Epic PR2 Modbus Comms Dropping out every 2 hours and 4 Mins ^{CODESYS Forge talk (Post)}
I think I am having a similar issue. Have you found out what was causing this problem?
Last updated: 2024-09-10

Post by ben1 on How to write multiple coils (Modbus FC15) ^{CODESYS Forge talk (Post)}
Yeah that is odd - sometimes you have to do what you have to do unfortunately. Have you tried sending consecutive bits in the word instead - ie. instead of [0].0. [1].0, [2].0 etc, send [0].0,[0].1, [0].2 etc. ?
Last updated: 1 day ago

Post by ph0010421 on TCP/IP client ^{CODESYS Forge talk (Post)}
Hello TCIS_Send needs to be longer than 4 bytes because idata is 28 bytes long. There may be other ways, but I would make a UNION with string/array of bytes. Write your STRING into the AsString part then copy the AsBytes part into TCIS_Send (Elements [3] to [30]) then 252 would be in [31] (I've assumed the idata is always the same length)
Last updated: 2023-12-19

Post by andreag0 on How to access to variable value through symbolic string name ^{CODESYS Forge talk (Post)}
Hello, anyone know how to get valiable value using a symbolic string name? For example: - send string to runtime using TCP/IP contains "GVL.TestINT" and get back the value. I need function that will translate the string to symbolic variable. Thank you. Andrea
Last updated: 2024-06-13

Post by nano on Cant login to Rpi4 but can see it in codesys communications settings. ^{CODESYS Forge talk (Post)}
which ports in detail are configured. the search of the rts works via broadcast-messages, programming with tcp-port on p2p-connection woth port-hopping, handled by runtime after siccesfully handshake. look at this entry on forge https://forge.codesys.com/forge/talk/Runtime/thread/4078a2ed28/
Last updated: 2024-06-23

Post by superjojo2002 on Licensing info not available. ^{CODESYS Forge talk (Post)}
If support for a containerized CODESYS runtime with a license isn't feasible, then I've considered an alternative approach: I've purchased and activated a "CODESYS Control Basic S" license on my Windows notebook, where I already have the Codemeter Control Center installed. Upon activation, I can see the CODESYS license as active on my notebook. Subsequently, I followed the instructions provided in this link (https://faq.codesys.com/display/CDSFAQ/How+to%3A+Setup+a+Wibu+Network+Server+Access+for+Licenses) to configure the Wibu runtime in the CODESYS container to access my external license server hosted on my notebook by editing the CODESYSControl_User.cfg file accordingly. However, it's worth noting that I'm still receiving a response from the Licensing Manager indicating that the runtime is persistently searching for a dongle instead of recognizing the soft container. So how can I get my runtime licensed now? Any ideas?
Last updated: 2024-03-20

Post by kronlundo on Licensing info not available (WAGO PFC200 + Codesys V3) ^{CODESYS Forge talk (Post)}
Hi! We're using a WAGO PFC200 for several projects towards the energy sector, and recently upgraded to CODESYS V3. We have the "IEC 60870-5-104 Server" package in a test program, and it works well with the package in DEMO mode. However, when we acquired a license for the "IEC 60870-5-104 Server" package and tried to add the license on the PFC200 through the license manager, we get an error (see attached file). It seems like there is no CmContainer on the device, does anyone have an idea on how to fix this? We've also contacted WAGO on this issue a while back with no feedback yet.
Last updated: 2024-06-10

Post by peterned on Programatically restart Codesys OPC UA server? ^{CODESYS Forge talk (Post)}
Hi, I'm using a Festo Codesys PLC (CPX-CEC-C1-V3), which is connected to a HMI panel. Both exchange data via OPC UA. Occasionally, the HMI stops displaying data, and looks as if there is no connection. If the HMI stops, the only way to make it work again is to restart the PLC. Restarting HMI has no effect. When the PLC is restarted, HMI starts working normally again. Is it possible to restart the OPC UA server from PLC code? I hope this will make fixing the HMI possible without a PLC restart. Thanks
Last updated: 2024-07-19

Post by alimans on OPC-UA Server, Symbol Set: Raise an error: Object reference not set to an instance of an object. ^{CODESYS Forge talk (Post)}
Hi everyone, I just created a very simple library without any code and, added it to my very simple project. after adding this library, I get an error when I try to open "Symbol Set" in "OPC UA Server" in "Communication Manager". Here is the code of my POU in the library: FUNCTION_BLOCK POU VAR eCommand : (CMD_NONE:=0, CMD_RESET:=-1) INT := CMD_NONE; END_VAR Attached is the error that I get. I also noticed that by removing the enumeration variable above (eCommand), I can open the "Symbol Set" again. Anybody has any idea why this error is raised and how could I use enumeration variables without error in "OPC UA Symbol Set"?
Last updated: 2024-08-08

Post by yannickasselin on codesys VLAN tagging ^{CODESYS Forge talk (Post)}
Hi, I am looking for exactly the same thing. I would think that using a layer 2/3 managed switch should work but I am not convinced. I would like to test it in order to see if it would be possible to run many Codesys Docker instances on a server and run only 1 ethernet cable from the server to a managed switch closer to the machines beeing controlled instead of having to run multiple long ethernet cables. I was going to buy a managed switch in order to test it but I want to first make sure it is possible and I want to figure out exactly what kind of switch I would need. Is this even possible? I think this is a feature that would be very useful paired with "Codesys Virtual Control SL". Thank you
Last updated: 2024-09-07

Post by thn-power on How to change OPC NodeId IdentifierType ^{CODESYS Forge talk (Post)}
Hi Yet another OPC UA question. When setting up a OPC server using "Communcation manager" (Symbol set and information model) in Codesys the NodeId is always given as "opaque" type. At least when browsing using UAExpert. Other standard OPC objects use numeric (or string) identifier, but for some reason my variables seems to get opaque/binary type. See attached photo. How can I change this? I can't see that this is a parameter in the CodesysControl.cfg. Can this be specified in the information model nodeset? And is it possible to specify the exact numeric or string NodeId for each instance? And on a related topic, is there a way to export the OPC server nodeId's with variable name so that it can be imported in a OPC Client? The .xml files in the project folder does not seem to contain the NodeId.
Last updated: 2024-09-20

Post by gediminas on Datasource OPC UA client system failure ^{CODESYS Forge talk (Post)}
I am using CODESYS v3.5 SP20 Patch 3 / Control for BeagleboneBlack SL v4.13 and after some time the OPC UA Server crashes. However, Runtime still works without any issues. The events leading up to the OPC server crash are the most suspicious: 1) Mutex deadlock detected - owner thread died, and 2) Runtime received SIGABRT. And it seems very similar with this topic except used versions - issues should be fixed with previous SP's. I can't seem to find any information about these events. Need some pointers in the right direction on how I can fix this problem.
Last updated: 2024-10-25

Sort by relevance or date