Post by ph0010421 on Add device greyed out ^{CODESYS Forge talk (Post)}
Click on NET in the project tree and add it there.
Last updated: 2023-12-19

Post by svn123 on In Simulation Mode, logic is not executing ^{CODESYS Forge talk (Post)}
Please check the attached snapshot. I am converting an int to real and storing in rVlv01_SV and then scaling the value using LIN_TRAFO. In the bottom Status Bar of Codesys, both RUN and SIMULATION are visible. When I enter value 100 as input to INT_TO_REAL instruction and press Ctrl-F7, the value can be seen at the input but the logic seems not to work. I searched for help but could not find anything relevant. What could be the reason. Codesys ver3.5.11 svn
Last updated: 2023-12-25

Post by eschwellinger on Add licence ^{CODESYS Forge talk (Post)}
Which plc and in which version? Runtime Type? Runtime Version?
Last updated: 2024-01-05

Post by toby on SM Drive license error ^{CODESYS Forge talk (Post)}
Hi albert1999 and forest, I hope you are well. I too am wondering if you have found any solutions? Im working with a RPi and a Omron R88D-ETH servo amplifier. The SoftMotion is timing out after 30min without the license, but I cant figure out how to license it, and I seem to have some compatibility issues between my RPi license and any SoftMotion licenses. Did you guys have any luck? Thank you very much for any assistance offered. Toby
Last updated: 2024-01-10

Post by warrumungi on Beckhoff EL6652-0010 with Codesys ^{CODESYS Forge talk (Post)}
Hi Has anyone successfully used a Beckhoff EL6652-0010 Ethernet/IP slave terminal through an EK1101 EtherCAT coupler, or similar, and been able to set it up through Codesys? It seems there is no driver for it, and it can't be done? The only option would be to use the Ethernet/IP capability of the controller directly with one of its ethernet ports and a Codesys Ethernet/IP adapter + module and routing it through EtherCAT by tunnelling it through via an EL6614 switchport? Any advice would be appreciated. Billy.
Last updated: 2024-01-15

Post by ojz0r on INT_TO_WORD function not working ^{CODESYS Forge talk (Post)}
That calculation will not work the way you expect it to. If PumpFillSpeed is limitied to 0-50 then the only whole number would be 50/50 = 1 everything else is 0.0-0.9999... and since you are using word and integer only 50 would work since there is no representation for mantissa in integer values. Declare a temporary real variable and do the calculation and then do a REAL_TO_WORD in the DRV2Speed assignment.
Last updated: 2024-01-26

Post by wbj0t on System libs and I/O Drivers ^{CODESYS Forge talk (Post)}
Hi everyone. My question about: where I can learn (read or watch) an info about codesys workflow through the system IO libs? I want to know how to implement I/O drivers by my self. In the system libs I see many interfaces, methods etc... But there is no explanation about them, just names of methods and fields of the FBs. I know about this page: https://forge.codesys.com/drv/io-drivers/doc/Generic/ There is so BIG the device description file and not so clear explaining of the attributes and elements, also some elements or attributes missed at it all. Yes, there are code examples on this page, but, so shortly and, for example, code about Modbus drivers is absent. And even if I try to add the IoDrvFB with lib, I get and error, something like: "failed to load IoDrvFB driver". And what about the book of codesys that written by Gary Pratt? Is there information about system libs and drivers in this book more clearly? Thank you :)
Last updated: 2024-02-02

Post by ferrim on IEC 61499 ^{CODESYS Forge talk (Post)}
IEC 61499 is probably something more complex than what you have correctly said so the prospects are interesting but we cannot ignore that it came out almost 20 years ago and has not won many hearts. I started to explore this world with a PLCnext controller because I love these devices based on RT Linux and Codesys is somehow usable with them but I have made little progress and I feel like inside a nutshell in the middle of the sea ;-) Gary's voluminous and precious book is always on my desk...
Last updated: 2024-02-10

Post by eschwellinger on Raspberry and problem with runtime ^{CODESYS Forge talk (Post)}
will be solved with 4.11.0.0 release scheduled tor 20th February
Last updated: 2024-02-14

Post by jackbrady on Function Blocks and arrays of function blocks ^{CODESYS Forge talk (Post)}
Thanks for the reply. Much appreciated.
Last updated: 2024-02-15

Post by timvh on Automatic xExecute NBS.TCP_write ^{CODESYS Forge talk (Post)}
Use e.g. the condition: TCP_Connection_0.xActive AND NOT(TCP_Write_0.xDone)
Last updated: 2024-03-05

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi everybody We are currently working on a project with an RS232 serial COM interface and using the CAA SerialCOM library. We have it working fine reading and writing data, although we have found an issue we cannot resolve and any suggestions would be helpful. We have noticed that after a while the RS232 stops working. We have tracked this down to the HANDLE hCom keeps increasing and when this reaches 1023 the COM returns an unknown error "5003". Is there a way to reset this hCom reference? Thanks Richard
Last updated: 2024-03-22

Post by pjoret on IFM CR711S Can Low Level Library Use ^{CODESYS Forge talk (Post)}
Hello, I'm using CR711S from IFM and I would like to use the CAA Can Low Level in de Safety part. I already use it on the Standard part and it works properly. I would like to know if there is some restriction on using it on the safepart of the PLC (I tried but my PCL put himself in Stop...) ? And if you have some example or even a forum with some types on IFM and CoDeSys, I would Take It. Have a nice Day.
Last updated: 2024-04-03

Post by yofi on Raspberry Pi 4 POU not running ^{CODESYS Forge talk (Post)}
I have this error where the pou doesn't run even for simple programs like contact and a coil if i remove the pou from the task and put another one it works for one run then it stops working again in the photo we can see a contact is on but the coil connected to it is still not on and the device is in run mode I had this issue again and again any help
Last updated: 2024-06-02

Post by yofi on Raspberry Pi 4 POU not running ^{CODESYS Forge talk (Post)}
I have this error where the pou doesn't run even for simple programs like contact and a coil if i remove the pou from the task and put another one it works for one run then it stops working again in the photo we can see a contact is on but the coil connected to it is still not on and the device is in run mode I had this issue again and again any help
Last updated: 2024-06-02

Post by nelsonreis on Help with IFM EcomatController CR710S in Codesys ^{CODESYS Forge talk (Post)}
Hi, Recently I bought a CR710S controller from IFM. I installed Codesys V3.5 SP11 as recommended and all required packages (including the safety packages and the IOWrapper package). However, I can't even open the project template without getting errors related to libraries failing to load (below in the first print screen). Then, clicking ok appears only 2 errors (second print) and when trying to go to simulation and login I get another 2 different errors (third print). I really appreciate any help anyone can provide, I'm completely stuck on this right now.
Last updated: 2024-06-04

Post by mozed on Windows 11 and SP17 ^{CODESYS Forge talk (Post)}
Try to use this version: https://store.codesys.com/de/codesys-installer.html
Last updated: 2024-06-12

Post by rene-h on VU.FbOpenDialog - TargetVisu - 2 x WebVisu ^{CODESYS Forge talk (Post)}
Hello, i am trying to find a way how to open Dialogs on a Single Visu. The options from VU.Globals are Target and WebVisu, but Webvisu opens the Dialog on both WebVisus and it should be separated. CurrentVisu can only be used when the Dialog is called from the Visu, but its all done in the Code. One Webvisu is for the User and one is for diagnostic reasons, and they should not be interfered from each other. Maybe someone can help me with this. Thanks
Last updated: 2024-06-13

Post by mos89p on Get DataSources Items list and status ^{CODESYS Forge talk (Post)}
Hello did you succeed?
Last updated: 2024-06-18

Post by eschwellinger on SysProcessExecuteCommand2 and CANopen Device ^{CODESYS Forge talk (Post)}
please call sysproccess in an own task with low prio
Last updated: 2024-06-20

Post by rabaggett on No Visu on RasPi ^{CODESYS Forge talk (Post)}
Hello, I have been having trouble getting a visualization to show up on the RasPi. I have previously used both WAGO touchscreen and Windows ControlWin and had no trouble. The visu does not show on the Raspi screen on start of the program and attempts to view in a browser both on the Raspi (Chromium) and from my laptop (Brave,Chrome,Firefox) running Codesys development fail. The visu shows correctly in Codesys development when online. (Win 11) The control code that is active is operating correctly. Raspi Codesys runtime is licensed. What am I missing? Thanks!
Last updated: 2024-06-20

Post by eschwellinger on SysProcessExecuteCommand2 and CANopen Device ^{CODESYS Forge talk (Post)}
which runtime version is it? 4.11.0.0?
Last updated: 2024-06-21

Post by wollvieh on License Activation Problems ^{CODESYS Forge talk (Post)}
on a raspberry pi delete the folder and its content before licensing. /var/opt/codesys/cmactlicense If you plug this SD card in another raspi ( which has another hw-serial number) you'll get a second empty softcontainer. This could lead to an unlicensed PFC (it could only handle one container) The solution is: To delete the /var/opt/codesys/cmactlicense directory and content of it and then aktivate the lizenz via WibuCmRau file and Lizenzmanager.
Last updated: 2024-06-24

Post by shaun on GAMP 5 and 21 CFR Part 11 ^{CODESYS Forge talk (Post)}
Good day I have been asked to do a project. It is for a pharmaceutical application and data needs to be logged. The spec calls for the control system to comply with GAMP 5 and 21 CFR Part 11. From what I can find online it's got to do with electronic records and validation. Has anyone developed any software using this or are there codesys librarys that can make my life easier in writing this code
Last updated: 2025-10-22

Post by ben1 on How to stay in a method until something is finished. ^{CODESYS Forge talk (Post)}
Why must you use a method? Top of my head can't you just use the button to turn on a bit and use it in a normal task? Just turn a bit on with the button, and run a TON from it in code, and turn it back off with the ton. And then just log the pressure on both the rising & falling edge?
Last updated: 2025-11-03

Sort by relevance or date