Post by dantheman on Connecting to SoftPLC Only Works By Turning Off Modbus Ethernet Port ^{CODESYS Forge talk (Post)}
I have an IPC with 2 ethernet ports and 1 Wi-Fi. I'm using ModbusTCP with the ethernet port named "enp2s0" connected to my remote I/O. This works fine when testing with Python and also works with CODESYS, but CODESYS is only able to scan for the Linux SoftPLC when I turn off the "enp2s0" interface. In other words, I can't get online with the IDE if I want my ModbusTCP comms to run with CODESYS. I'm using a Linux SoftPLC that has the following entry in CODESYSControl.cfg, hoping that this will allow me to connect with "enp1s0" or "wlp3s0", and leave "enp2s0" for field comms, but this seems to only make the source IP of the ModbusTCP comms to be bound to "enp2s0". That last point is the case only if I don't restart the service, but if I do restart the service after changing the config file, the source IP for the ModbusTCP comms then becomes the one for "enp1s0", which is very confusing to me: [SysSocket] Adapter.0.Name="enp2s0" Adapter.0.EnableSetIpAndMask=1 On the device list, I only have "enp2s0" given as the ethernet device that has the ModbusTCP master & slave beneath it, shown in Screenshot 1. On the IPC, I can ping the ModbusTCP client (remote I/O) from "enp2s0", and I've attached a Wireshark capture of running ModbusTCP from the CODESYS runtime as Screenshot 2, 3 & 4 (again, I can't get online when this is running, I have to turn off "enp2s0" to connect even when it's idle and I don't have an active TCP session with my Python tests). Like I explained above, the source IP is "enp1s0", even though the ethernet device on the project is "enp2s0". I was lucky to catch the red message that showed the source IP that makes sense to me (the one for "enp2s0"), but for some reason that connection was reset and I never saw that packet again. I've also tried this with Auto-reconnect both enabled & disabled, for the ModbusTCP Master device. I also have to turn off "enp1s0" and then turn it on, just so that I can have the ModbusTCP comms running from "enp2s0" (which is not intuitive in any way to me, I'd love some help understanding that phenomenon as well) in the weird manner that I've described above. I would be very appreciative if someone can help me figure out this pickle. I'd love to just connect to CODESYS through my Wi-Fi interface and leave my ethernet ports for field comms.
Last updated: 2024-08-01

Post by timvh on Problem Reading Registers via Modbus from non Codesys device ^{CODESYS Forge talk (Post)}
According to the documentation: https://wiki.teltonika-networks.com/view/RUT956_Modbus You need to create a Channel to read 2 registers from address 143 to get the lattitude. It doesn't specify if you need to read it as a Holding Register or as an Input Register. You could try both. So in the Teltonika router, you need to enable it as being a Modbus Server. Then in CODESYS add an Ethernet Adapter, then a Modbus Client (Master) and to the Client (Master) add the Modbus Server (Slave). Set the IP address and add the Channel. The please consider that CODESYS doesn't update any variables when they are not used in the application. In the I/O mapping tab of your I/O configuration, you can set the "Always update" to enabled.
Last updated: 2025-03-08

Post by salmawis on Advice on OOP hardware I/O code structure ^{CODESYS Forge talk (Post)}
Call 10 FB instances. Connect Motor_1_Fault to the i_xHW_FaultDetected pin of FB 1, Motor_2_Fault to FB 2... By doing this, your FB will be flexible. The programming will be smooth like a perfect Drift Boss, instead of "hitting the wall" because it can't be reused!
Last updated: 2025-10-31

Post by bruno-roth on Parker Compax3 controlled by Schneider LMC 201 ^{CODESYS Forge talk (Post)}
Hello, You could not run EtherCAT-Softmotion drives with LMC201 PLC. This Controller has an EtherCAT master but only to run simple I/O devices. You could not use this EtherCAT master on the LMC201 for Motion. Schneider PACdrive Controller use SERCOS and only own drives (LXM62 with Sercos) for motion.
Last updated: 2026-01-13

Post by timvh on CODESYS: Combining Master Redundancy with EtherCAT Ring Topology – Is it Supported? ^{CODESYS Forge talk (Post)}
Yes, this works (at least we have it running with Wago PLC and Beckhoff I/O), but the concept works. You need 2 PLC's with at leat 3 network interfaces. And 2 switches (can be unmanaged). See the attached simple diagram for the solution.
Last updated: 2026-02-05

Post by sandro66 on Application-based license Modbus Channels ^{CODESYS Forge talk (Post)}
Hi Gatto, Using version 3.5.21.xx, it is no longer possible to use Modbus function blocks (I make extensive use of these FBs.)as shown in the example. https://content.helpme-codesys.com/en/CODESYS%20Examples/_ex_modbus_example.html The compiler detects one Modbus instance for each instance of the communication FB block. The example program above, although simple, reports 8 Modbus instances when compiled with the latest version. Codesys Support says that you must use fieldbus I/O mapping, but this will result in the loss of the ability to programmatically modify communication parameters. Sandro
Last updated: 2025-09-04

Post by marlutec on [ERROR] The PLCopenXML import is not possible because Device not found. Type: 89, Id: 0000 0005, Version: 3.5.10.0 ^{CODESYS Forge talk (Post)}
Hello every one. Now i'm instaling a Weintek cMT2108x2(v2) with IR-ETN40R. When I start to import the archive content the code of I/O remote IR-ETN40R, ocurred this error. [ERROR] The PLCopenXML import is not possible because Device not found. Type: 89, Id: 0000 0005, Version: 3.5.10.0 Can someone help me? Marcos Gentil, from Brazil.
Last updated: 2024-02-15

Post by ryusoup on 'keep last value' option in CODESYS EtherCAT ^{CODESYS Forge talk (Post)}
Hello, I’m using CODESYS EtherCAT Master on a Raspberry Pi controller with several remote I/O modules. I’m facing an issue where the input values from the remote I/Os drop to 0 when a connection error occurs. Is there a way to configure a “keep last value” behavior (i.e., hold the last valid input) instead of defaulting to 0 on communication loss? Best regards,
Last updated: 2025-11-18

Post by chris--o on ModbusTCP RaspberryPi zu Fronius Wechselrichter ^{CODESYS Forge talk (Post)}
Danke probier ich mal aus! Sorry für die späte Antwort.. War im Urlaub und hatte den Post hier wieder verdrängt.
Last updated: 2025-09-19

Post by russells on Codesys ControlWinV3x64 with EtherCat Slave ^{CODESYS Forge talk (Post)}
Hi there I am running Codesys ControlWinV3x64 (Patch 4) on my laptop for demonstration purposes but I am unable to get connection to the EtherCAT master and slave device. This is the process that I have followed: * Installed NPCap. * Added the xml file for the SMC slave device to the Device Repository. * Activated Control Win SysTray x64 and selected Start PLC. * Scanned the network for the local device (my laptop). * Added an EtherCAT master to the project and scanned the EtherCAT master for the Network and then selected the correct network. * Selected "Scan for devices" to identify the connected I/O. * Add the SMC EtherCAT slave manually because I was unable to scan it in. * Selected "Scan for devices". I have followed the steps described above but I can't scan in the EtherCAT slave or connect to it. I thought this situation was unique to the EtherCAT slave but I have also tried the same for an EtherNet/IP slave using the Ethernet Adaptor and EtherNet/IP scanner and I am also unable to scan in the device or activate the EtherNet/IP network. Any assistance will be appreciated.
Last updated: 2026-02-04

Post by davidb on Initialisation TimerSwitch of Util Codesys 3.5 Library ^{CODESYS Forge talk (Post)}
jf89 Hello!Good morning You got it to use the function block Timer Switch for your application? I'm needing to do one system that turn on at 8:00am o' clock and turn off at 17:00pm o' clock, from Monday to Friday. Please, can you help me?
Last updated: 2024-10-14

Post by danielbeers on Automation Server + Pi Gateway + PLC w/ CAN ^{CODESYS Forge talk (Post)}
Hello, I have a project using some EPEC PLC's. Some of them are programmable using Ethernet and some use CAN. We currently have a Raspberry Pi that is acting as a gateway to the Codesys Automation Server and is successfully working for the PLC's communicating over ethernet. I am trying to achieve a similar result for the PLC's that have only CAN access. I have PEAKCan drivers on the Pi, and can successfully send/receive messages. But the Gateway does not recognise the PLC when scanned from the Automation server online. Is there a library or service that exists to translate the CAN messaging, to the Edge Gateway, and be able to achieve remote access with the Automation Server? Or is this not possible without creating something custom? Cheers, Daniel
Last updated: 2024-09-22

Post by siscu on Raspberry i2c master device ^{CODESYS Forge talk (Post)}
I want to implement an extended I2C master for Raspberry Pi Control. I was hoping for it to be as easy as creating a library with a FB that extends i2cMaster and associating it with a device following the forge drivers documentation, but I haven't managed to make it work as the driver behaves only as an i2c slave. I'm thinking this is because the forge forum only talks about extending i2c, and the master portion is omitted since most users won't want to add a custom one. I'd like to know if I'm doing something wrong. Is it really possible to make an I2C master extension device? If so, are there public examples we can check out? Any info on this topic will be appreciated.
Last updated: 2024-10-16

Post by cihangur on OpC UA server on Raspberry Pi 64 SL runtime ^{CODESYS Forge talk (Post)}
After my tests, I noticed two issues. 1- WinCC disconnects the connection after receiving the GetEndPointResponse message from CoDeSys. (I found it with UAExpert and Wireshark.) 2- It establishes a connection despite waiting for a while on the network with DNS. As a result of this information: I solved the problem by adding the line "193.193.193.150 t9pac" to the C:\Windows\System32\Drivers\etc\hosts file and making Windows accept messages coming from the IP number 193.193.193.150 as coming from t9pac. (t9pac is the name of my PLC running CoDeSys.) If there is a setting that will allow CoDeSys OPC UA to respond to GetEndPointRequest with its IP address, this problem will not occur.
Last updated: 2024-12-12

Post by reinier-geers on missing font ^{CODESYS Forge talk (Post)}
Hi I mis the font. Wenn i click i get an error
Last updated: 2024-02-26

Post by martinlithlith on Raspberry Pi: List of available drivers / libraries ^{CODESYS Forge talk (Post)}
As most of the posts are moved here around 2015, what would be the right version of codesys to run? Would it be better to install a older version of codesys or should i keep on downgrading libraries? Is there any work done to update theses libraries? It´s been a few years since the last update in this post, are there new libraries/devices for raspberry being added/posted somewhere else? Thanks, Martin
Last updated: 2023-10-17

Post by trusty-squire on How to adapt Codesys Control SL to custom board ^{CODESYS Forge talk (Post)}
For general usage, these links might help you out. If you are looking at using I2C interfaces, examples from the Raspberry Pi will probably be useful, even if your board isn't a Raspberry Pi. https://content.helpme-codesys.com/en/CODESYS%20Examples/_ex_rts_serial_com.html https://content.helpme-codesys.com/en/CODESYS%20Examples/_ex_raspberry.html If you're developing your own drivers, I can't help you there, although the link you provided will help. If you drill in deeper, the I2C page for example shows function block and method usage, etc. Good luck!
Last updated: 2024-08-09

Post by c3po on SNMP Communication with WAGO 750-8212 PFC ^{CODESYS Forge talk (Post)}
Hello folks, my problem is a bit bigger for just one question. So let's start with the easiest. But first, my system setup: It's a WAGO 750-8212 PFC with some I/O-modules. I try to communicate with the controlsystem over SNMP using the IIoT library from codesys. https://content.helpme-codesys.com/de/CODESYS%20Examples/_ex_iot_snmp_service.html Is there some expirience with this kind of communication? It's just about transfering some data from PFC to network and setting some analogsettings from network to the PFC. So my easiest question: Do I ever need the SNMP_Agent or can I use the SET / GET function as standalone, without the agent? (maybe some more questions will follow, if someone will answer to my request) thanks so far
Last updated: 2024-08-21

ModbusTCP, can i know when i get requests from slave side? ^{CODESYS Forge talk (Thread)}
ModbusTCP, can i know when i get requests from slave side?
Last updated: 2018-11-19

Every time I display the watch 1 window, I get a .Net exception ^{CODESYS Forge talk (Thread)}
Every time I display the watch 1 window, I get a .Net exception
Last updated: 2020-02-24

BUG: Why does I get garbage values when I use CONCAT and Array with CAA File? ^{CODESYS Forge talk (Thread)}
BUG: Why does I get garbage values when I use CONCAT and Array with CAA File?
Last updated: 2019-07-04

How do i measure time in code? I want to use SR04 distance sensor. ^{CODESYS Forge talk (Thread)}
How do i measure time in code? I want to use SR04 distance sensor.
Last updated: 2016-06-10

Post by kbazzett on "Sequent Microsystems" industrial automation hat raspberry pi ^{CODESYS Forge talk (Post)}
Here is a complete list of the Sequent Microsystems Pi hats that work in Codesys. https://github.com/SequentMicrosystems/SM_CODESYS/tree/main/ "For easy install download the .package file and open it on your computer, Codesys installer will know what to do with it." <- This. The Multi I/O Hat fit my needs because of the Analog I/O 4-20ma and RTD. I used a Raspberry Pi 5 and 64b install. The example project is also worth the download. With the sample project open, right click on the Raspberry Pi device and update to whatever you are using (SL, MC, 64b). Enable I2C on the PI. You can jumper the hats Analog Outputs to Inputs and see it function on the Web Visualization. Very Cool! I spent quite a bit of time trying to find this solution so hopefully this update helps others. Here is the video link on how to setup a Raspberry PI as a Codesys PLC https://youtu.be/RPoPscbo3Kc?si=Th4-n-mQ6g5fdHj8
Last updated: 2024-12-05

I can't scan my EK1100 ^{CODESYS Forge talk (Thread)}
I can't scan my EK1100
Last updated: 2022-08-03

can I share compiled code? ^{CODESYS Forge talk (Thread)}
can I share compiled code?
Last updated: 2016-07-25

Sort by relevance or date