Post by durstloescher on Codesys Input Detector ^{CODESYS Forge talk (Post)}
Good morning, I am currently working on implementing a display dimmer. I want the display to dim after X minutes. This works so far. The implementation is done via the Linux subsystem, to which a command is sent to dim the display. However, my problem is resetting the timer when input is received. I want the dimming timer to be reset with each click/touch. Unfortunately, I can't find a suitable solution for this. Are there any ways to do this? Codesys v3.5 SP19 Patch 2
Last updated: 2024-02-15

Post by kleeswi on SysFileOpen does not work after update to V3.5 SP19 Patch 5 ^{CODESYS Forge talk (Post)}
I use the function SysFile.SysFileOpen(sFileNamePara, SysFile.ACCESS_MODE.AM_WRITE, pErrorFileOpen); to open and write a file. Since the update from Codesys V3.5 SP17 to V3.5 SP19 Patch 5 it does not work anymore. I first had SysFile.SysFileOpen(sFileNamePara, SysFile.ACCESS_MODE.AM_APPEND_PLUS, pErrorFileOpen); in both versions. hFile_Test is a pointer to byte. It gives an exceptional error when dereferencing the hFile_Test pointer. Edit: I use Codesys on a Raspberry pi
Last updated: 2024-02-19

Post by martincapd on EWON ^{CODESYS Forge talk (Post)}
I have the same problem in that I can connect to the eWon and ping the controller IP Address, however I cant connect through CodeSys. I'm using Gateway-1 which is configured to use "IP-Address: localhost" and "Port: 1217". Rather than scanning the network for devices, I enter the IP Address of the device, codesys returns a "No Device is repsonding..." message. See attached. I'm wondering if the IP-Address used Gateway-1 should be "localhost" or the WAN/LAN IP of the eWon? Thanks for the help MC
Last updated: 2024-02-21

Post by martinla on New Codesys Library Dependencies ^{CODESYS Forge talk (Post)}
When creating a new Codesys library, I am getting 2 errors for missing libraries. I can see that I am using newer versions of these in the library manager (3.5.17.0 and 3.5.19.0 opposed to 3.5.8.0 and 3.5.7.0 stated in the errors). IDE Version is V3.5 SP19 Patch 6. The "Download missing libraries..." button in Messages list is not doing anything. Why is it looking for older versions of these libraries? Can this be fixed by using the newer versions? How can I download & install the older version of these libraries?
Last updated: 2024-02-29

Post by nano on Is there any support for I2C on Raspberry Pi? ^{CODESYS Forge talk (Post)}
hello jdj this question can be answered well with a pretty good forge documentation: https://forge.codesys.com/drv/io-drivers/doc/Generic/ u r also able to create in codesys directly an iec-code by using the i2c-interface as driver using the codesys ide and st depending on the stepperdriver, used in yöur hat, its possible that an driver is already available in the device-repository. which mcp-device is used on the hat?
Last updated: 2024-03-01

Post by timvh on Device logon problem following fresh install ^{CODESYS Forge talk (Post)}
In your project you selected the "CODESYS Control Win V3" as device, but the device you want to connect to is a "CODESYS Control Win V3 x64". Those are not the same. If you double click on the device during the network scan, you will get information that these are not the same, but that you can change the type in your project to the x64 bit type. Another option is to "right-click" on the device in the device tree of your project and select "update device" then select the x64 type.
Last updated: 2024-03-19

Post by remcoborghuis on C0032 Error to type Pointer to IoConfigParameter ^{CODESYS Forge talk (Post)}
Hi All, I'm using codesys on a raspberry PI. I use V3.5 SP18 Patch 2 development system and codesys for raspberry pi 4.8.0.0. Sometimes when I build the project I get error messages C0007: Expression expected instead of ',' and C0032: Cannot convert type 'Unknow type: '!!!'ERROR'!!!" to type 'POINTER TO IoConfigParameter'. I can't click on the message to bring me to the fault. After I do a "Clean all" the build finishes successful. Anyone who can help me with this problem? Thanks! Remco Borghuis
Last updated: 2024-03-25

Post by marcolim on RPC failed 0x16c9a085 ^{CODESYS Forge talk (Post)}
Hello Matteo, I think the problem is about configuration of firewall (windows firewall usually). You can disable temporary the firewall to check if the communication works. Eventually you can: Go to the control panel -> Windows Defender Firewall -> Allow an app or feature Enable the options to change the settings. Scroll down in the application list to CODESYS and CODESYS ControlService. If you don’t see this application add it to the list. Make sure that all the checkboxes are checked (Domain, Private and public).
Last updated: 2024-04-01

Post by valenting on Problem with Licenced Software Metrics ^{CODESYS Forge talk (Post)}
Hi, When I try to install my codesys program with the new application-based licensing, I have an error "it exceeds the scope of the license agreement. See Device > Licensed Software Metrics" In the Licensed Software Metrics section, I see a code size < 3MB and less than 2700 variables in visualiaztions. I'm using a license "Control Basic L" with "Codesys Visualization L" option, so it should be enough with these metrics. What can I do ?
Last updated: 2024-04-22

Post by eschwellinger on License problem gateway ^{CODESYS Forge talk (Post)}
I just try to help. Anyway it is a big difference if a Store SL runtime or an oem plc and licence is used. These licenses need to be activated on plc side - so you have dependencies to the version (CODESYS and Runtime Version) Did you ever ask Epis out for this situation? They should know which license fit to their device. Even they should know if the device is capable for Softmotion and see the requiremnts in the CODESYS store: Runtime 4.9.0.0 - how should this work with Epis 3.5.16.x? Anyway refund is not a problem.
Last updated: 2024-04-26

Post by dkugler on Codesys SVN ^{CODESYS Forge talk (Post)}
Don't set on SVN. The service phase has started in March 2024 and will be discontinued in 2027. We actually use SVN and have to switch to GIT in the future. As I informed, there is no way of getting a single SVN or GIT licence. I' dont understand, why Codesys forces us customers to pay for an expensive Professional Edition paket from year to year using only one part of it! If you find a way to buy a single licence, let me know.
Last updated: 2024-04-29

Post by alez on CANOpen SDO to write VISIBLE STRING ^{CODESYS Forge talk (Post)}
Hello, I am experiencing difficulties in configuring a CANopen device by sending SDOs. In particular I am attempting to write an Object Dictionary that has VISIBLE STRING as the Data Type. When I try to configure the sending of an SDO from Codesys to configure this parameter I am not allowed to enter a string value. In my particular case I am trying to change the Manufacturer Device Name ( Index 0x1008 ). Could it be that Codesys doesn't manage these types of variables?
Last updated: 2024-04-29

Post by richard-wang on Codesys recipe manager - what does it do? ^{CODESYS Forge talk (Post)}
Hi All Thanks for sharing this information. For whom may not know why always get error code 16#4000 or 16#4002 while performing Recipe commands, the root cause is There is a line need to be inserted in CODESYSControl.cfg file, which is PlaceholderFilePath.1=/var/opt/codesys/PlcLogic/ I am using Pi, therefore the above path is set to my pi unit, after adding above line to my cfg file, all the Recipe commands work fine. But I still do not know how and when this file got modified though.
Last updated: 2024-04-29

Post by rabaggett on CODESYS control for Raspberry Pi 64 SL errors ^{CODESYS Forge talk (Post)}
Update: I started over. I saved progress at each step. all compiled zero errors, zero warnings. Pre-processor messages remain, but I can make progress. Until I try to re- load the project file in Codesys. Re-loaded files error as above when compiled, even though they compiled error-free immediately before saving. Is my installation borked? (Not easy to re-install due to IT madness...)
Last updated: 2024-05-03

Post by totorovic on Softmotion not working with simulation mode ^{CODESYS Forge talk (Post)}
Good morning, I think that the mode Simulation does not support the Softmotion functionnality because it runs the CODESYS process with normal priority wich is not a good thing for real-time behavior. If you want to test your PLC project, please use a Codesys Control Softmotion (and your computer must have the Ethercat driver installed) or much easier, download your code into the C6 Smart. BR
Last updated: 2024-05-13

Post by paro on send appliaction files to wago plc (codesys 3.5) via ssh ^{CODESYS Forge talk (Post)}
Hi, it is enough to copy the files to /home/codesys/PlcLogic/Application and adding the lines [CmpApp] Application.1=Application to the eRUNTIME.cfg, if your Application in your program is also called "Application". Reboot -> Bootapp should be loaded. If not please check the log /var/log/runtime.log There should be a line which explains why the bootproject is not loaded.
Last updated: 2024-05-29

Hi, I try to send and receive data using a UDP connection via SysSocket 3.5.17.0. While sending data works fine, I have problems with the receiving part. I am able to capture the received data of client side in wireshark But unable to capture it on the codesys ^{CODESYS Forge talk (Thread)}
Hi, I try to send and receive data using a UDP connection via SysSocket 3.5.17.0. While sending data works fine, I have problems with the receiving part. I am able to capture the received data of client side in wireshark But unable to capture it on the codesys
Last updated: 2024-06-03

Post by kris-samoy on Get Alarm status in Codesys ^{CODESYS Forge talk (Post)}
I am rather new to Codesys and I'm trying to figure out how to get the status of an alarm. This to interlock the start of a device until the alarm has been acknowledged... I am not sure if IAlarm.GetState (METH) can be used for this purpose. If yes then could someone please briefly explain how to use this? https://content.helpme-codesys.com/en/libs/AlarmManager/4.1.0.0/Interfaces/pou-IAlarm/GetState.html Thx & grtz, Kris
Last updated: 2024-06-03

Post by nelsonreis on Help with IFM EcomatController CR710S in Codesys ^{CODESYS Forge talk (Post)}
Hi, Recently I bought a CR710S controller from IFM. I installed Codesys V3.5 SP11 as recommended and all required packages (including the safety packages and the IOWrapper package). However, I can't even open the project template without getting errors related to libraries failing to load (below in the first print screen). Then, clicking ok appears only 2 errors (second print) and when trying to go to simulation and login I get another 2 different errors (third print). I really appreciate any help anyone can provide, I'm completely stuck on this right now.
Last updated: 2024-06-04

Post by bitwitch on Einheiten umrechnen, Numpad und Eingabegrenzen ^{CODESYS Forge talk (Post)}
Das Codesys-Objekt 'Einheiten umrechnen' wirkt auf timeVar (TIME) z.B. innerhalb eines Visu-Rechtecks und funktionier in den Grundfunktionen einwadfrei. Die Ausgabe der Std. von timeVar läuft. Beispiel: Bei t#3d2h10m wird wunschgemäß 74h (volle Std-Anzahl). Die Grenzüberwachung Max= 10 funktioniert nicht, da die Angabe scheinbar ms erwartet (arbeitet mit 10ms). Irgend wie muss man jetzt codesys davon überzeugen, dass auch für Min und Max die Einheitenumrechnerei wirken soll, wobei die Eingabe der Grenzen in Std erfolen muß. Hat jemad einen TiPPPPPPPPP?
Last updated: 2024-06-14

Post by nano on How to access to variable value through symbolic string name ^{CODESYS Forge talk (Post)}
i know, this is the reason for us either. PLC-Handler is to big, and only available with additional Contracts/Costs. OPC-UA is to slow for us. As described, there is a solution available, but im not allowed to post them here. i would prefer you send a message at codesys store by "have a question" or similar called. Not sure. Or, if an Codesys-Official Member allows to share that informations, i can give you the right hints.
Last updated: 2024-06-15

Post by wollvieh on License Activation Problems ^{CODESYS Forge talk (Post)}
on a raspberry pi delete the folder and its content before licensing. /var/opt/codesys/cmactlicense If you plug this SD card in another raspi ( which has another hw-serial number) you'll get a second empty softcontainer. This could lead to an unlicensed PFC (it could only handle one container) The solution is: To delete the /var/opt/codesys/cmactlicense directory and content of it and then aktivate the lizenz via WibuCmRau file and Lizenzmanager.
Last updated: 2024-06-24

Post by sajid on NMEA Serial data read in Control win v3 x64 ^{CODESYS Forge talk (Post)}
I am using the SerialCom example program from the CODESYS website to read NMEA strings in CODESYS Control Win V3 x64 through a serial-to-USB converter. However, I occasionally receive only partial data or encounter errors in the received string. A screenshot of expected NMEA string attached for reference. Could you please advise on how to ensure the full NMEA string is received consistently? Error in strRead variable is <value of="" the="" expression="" cannot="" be="" retrieved=""></value>
Last updated: 2025-10-16

Post by sajid on NMEA Serial data read in Control win v3 x64 ^{CODESYS Forge talk (Post)}
I am using the SerialCom example program from the CODESYS website to read NMEA strings in CODESYS Control Win V3 x64 through a serial-to-USB converter. However, I occasionally receive only partial data or encounter errors in the received string. A screenshot of expected NMEA string attached for reference. Could you please advise on how to ensure the full NMEA string is received consistently? Error in strRead variable is <value of="" the="" expression="" cannot="" be="" retrieved=""></value>
Last updated: 2025-10-16

Post by mizi on SM_Drive_Virtual ^{CODESYS Forge talk (Post)}
Hi I recently started learning Codesys SoftMotion. At first, I mainly used YouTube videos. I stopped at two videos where the same problem keeps recurring. fbReadPos( Axis := X_Axis, Enable := TRUE, Position => gAxes.lrActualPos); <- axis cannot move I checked the entire code line by line. Zero errors. GPT spits out nonsense, throwing up increasingly worse errors. And when I copy its code, it says the code is wrong and gets stuck in a loop of its own stupidity. Can anyone explain why it doesn't work? Link to the video below: https://www.youtube.com/watch?v=CYa2HvYZgbM&list=PLsEhEcYjG7na0OveU7cqFXBx7ATyGGn0A&index=3
Last updated: 2025-10-21

Sort by relevance or date