Post by trusty-squire on How to adapt Codesys Control SL to custom board ^{CODESYS Forge talk (Post)}
For general usage, these links might help you out. If you are looking at using I2C interfaces, examples from the Raspberry Pi will probably be useful, even if your board isn't a Raspberry Pi. https://content.helpme-codesys.com/en/CODESYS%20Examples/_ex_rts_serial_com.html https://content.helpme-codesys.com/en/CODESYS%20Examples/_ex_raspberry.html If you're developing your own drivers, I can't help you there, although the link you provided will help. If you drill in deeper, the I2C page for example shows function block and method usage, etc. Good luck!
Last updated: 2024-08-09

Post by shawn-plc on Return value from a tag given a string literal ^{CODESYS Forge talk (Post)}
Good afternoon everyone, I am looking for a way to return a value given a string tag path. I put together a pseudo-example to illustrate my use-case and was wondering if anyone in this forum can help. The function fnValueFromTagPath is the function I am looking to either create or use from existing library. I would greatly appreciate it. Please see the attachment for additional detail. -Shawn
Last updated: 2024-08-13

Post by liamb on Converting CANbus to Decimal from signed 2's complement ^{CODESYS Forge talk (Post)}
I need to combine two 8 bit CANbus messages to 16 bits signed int then convert to decimal Decimal from signed 2's complement. I've been using the below code to read for new messages, combine them then assign them to a variable What is the best way to do this for from signed 2's complement? fbRxMessage351(Data := RxMessage351Data); IF fbRxMessage351.NewMessage THEN ChargeVoltage := (WORD_TO_REAL((RxMessage351Data[0]) + ((RxMessage351Data[1]) * 256))) * 0.1; END_IF
Last updated: 2024-08-16

Post by mini-developer on Precompilation Error NBS.UDP_Peer ^{CODESYS Forge talk (Post)}
Hello, I use the Library NBS from "caa net base services". After opening the Project i get 19 errors from the message window "Precompilation", most of them because it doesn't recognise a component of the FB "NBS.UD_Peer". (see photo) After compiling the Project at least 2 times, there are no errors. Is there a reason and solution for this behavior? Is there a problem with resolving the library? Thanks for any clue
Last updated: 2024-08-23

Post by dkugler on EThercat Dynamic configuration ^{CODESYS Forge talk (Post)}
I can confirm that at my 4ms EtherCAT Master the frames per second is equal at round about 500 with Codesys SP19. The same program at SP16 it was at 380-430 f/sec. for me it will be interesting too, whats the reason is for this high frame count/sec? I havn't had the time to use a paket sniffer and analyse all the frames. I can't help with your other questions, sorry.
Last updated: 2024-09-19

Post by wbj0t on tool 'update raspberry pi' unavailable ^{CODESYS Forge talk (Post)}
Doesnt matter. I have installed sp20 with latest RP 4.13. Same problem. Anyway My large project in RP 4.10 and SP 19 and I need these versions and use same installation programm for Codesys IDE and RP4 package. I did install again, because my SSD broke and now cant update raspberry... I dont know how to translate correctly project to newest version - there are 52769 errors and incompatabilities: after updates libraries anyway some errors still because of devices... I found solution with .deb file from raspberry package - dont need IDE anymore for update raspberry.
Last updated: 2024-09-27

Post by davidbo on RPI can system operation like rm in a shell have an impact on a Task cycle time ^{CODESYS Forge talk (Post)}
CODESYS Control for Raspberry Pi MC SL v4.4.0.0 CANopen_Manager 4.2.0.0 I did not call rm directly from my TASK-i2c, it was trough the attached python script. It is not always a problem happens, but sometimes a rm takes a long time. I reduced the amount of calls to logi2c.py but I don't understand why TASK-i2c sometimes can cause problems for TASK-CAN
Last updated: 2024-09-27

Post by davidbo on RPI can system operation like rm in a shell have an impact on a Task cycle time ^{CODESYS Forge talk (Post)}
CODESYS Control for Raspberry Pi MC SL v4.4.0.0 CANopen_Manager 4.2.0.0 I did not call rm directly from my TASK-i2c, it was trough the attached python script. It is not always a problem happens, but sometimes a rm takes a long time. I reduced the amount of calls to logi2c.py but I don't understand why TASK-i2c sometimes can cause problems for TASK-CAN
Last updated: 2024-09-27

Post by garmusd on Raspberry Pi 5 GPIO not working. ^{CODESYS Forge talk (Post)}
I paid money for the RPi runtime because the Product Description says that GPIO is supported. It is also written in the Versions that since 4.11 RPi5 is supported. And I use 4.13. Nowhere is it mentioned that GPIO is still not supported... It's a pity that the Codesys developers still can't find a way to fix it. Are there plans for when it will be fixed or are the developers too weak? Just wondering, is there anyone with a working GPIO? Can you share the details of your system?
Last updated: 2024-09-27

Post by timvh on Communication between applications on same device/controller/runtime (Win RTE 3.5.20.20) ^{CODESYS Forge talk (Post)}
The RTE will take the RTE license. The HMI will take the HMI license. For the Application Based Licenses, the Runtime will take the smallest which is required. So if you have an application running EtherCAT and no visualization, only the Control with support for EtherCAT is used. If you have another runtime which requires the visualization, it will take the smallest Control license which is required and available + the smallest visualization license which is required.
Last updated: 2024-10-01

Post by paulpotat on Can't open license manager with raspberry CM4 ^{CODESYS Forge talk (Post)}
Hello, I have a problem when opening the license manager for my raspberry pi (CM4 model) with runtime 4.13.0.0. I select "Device" --> "Soft Container" and click on my device in the scan window but I get this error message : Licensing info not available. There is no dongle attached to this device. I can't install licenses anymore, and I don't understand why is CodeSys looking for a dongle when I specified I wanted to use a Soft Container. Can somebody help me please ? Best regards
Last updated: 2024-10-04

Post by mini-developer on Profinet Exor connection drop ^{CODESYS Forge talk (Post)}
Hello, I have a Exor HMI with 2 seperatred ETH interface's. It is Configured as PN Master on ETH interface 1 and the IO's are working, as long as the development PC is connected to the ETH 0 interface. When the PC is disconnected, the PN communication drops and a reconnection is started. I installed the newest device description for Codesys and Firmware for the Panel. The IO Gateway is from Weidmueller What could cause the Problem?
Last updated: 2024-10-16

Post by ricardoteles97 on Trends Error: TrendStorageAccess: prvCheckForSizeLimit ^{CODESYS Forge talk (Post)}
Hello, I currently have my trend configured with a maximum size limit of 5MB (additional settings can be seen in the attached image). However, I am encountering an error related to this trend, specifically within the TrendStorageAccess library. The device log shows the following message: TrendStorageAccess: prvCheckForSizeLimit (see the attached image for details). Does anyone know the reason for this error? Additionally, where can I find more information to troubleshoot this issue? Thanks in advance!
Last updated: 2024-10-16

Post by winki on Modbus TCP & RTU with Control for Linux SL ^{CODESYS Forge talk (Post)}
For small project, I would like to use my industrial computer as a PLC + Industrial Computer. Like that I can save the cost of one PLC. That why I am using Codesys on Linux. With the nic it is not working. I already set the IP adress with /etc/network/interfaces. Can it comes from there ? looking to "Control Linux SL" docuemntation it should work with rtu.
Last updated: 2024-10-23

Post by jeroenaero on CodeSys Raspberry pi I2C driver not found ^{CODESYS Forge talk (Post)}
I succeed to change the device to PI_SL but still the same problem of the I2C device switching between running and not running. the only difference with your project is that yo use I2C_master device version 4.7.0 and i 4.7.13, for GPIO i also use the 4.7.13 version and you the 4.7.0. Can you send me the older version of the Raspberry PI pheripals library, because i cannot choose lower version then 4.7.10 for the GPIO and I2C_master device
Last updated: 2024-11-11

Post by jeroenaero on CodeSys Raspberry pi I2C driver not found ^{CODESYS Forge talk (Post)}
Finnaly i get it working. There was a line in the file that set the ADS1015 chip in /boot/firmware/config.txt which i removed and after that the ADS1115 has a green turning circle and i got values. i created a new component so it fits our ADS1015. see screenshot. It works also with Codesys Control for Raspberry Pi 64 SL after adding the ULINT_TO_UDINT conversion in the library. i think the chip was all the time in use by the Raspberry pi itself. Thanks for your help!
Last updated: 2024-11-12

Post by aliazzz on Raspberry Pi 3: Linux/ARMHFv7 unknown container technology ^{CODESYS Forge talk (Post)}
Hi CODESYS team! It seems Podman for Raspberry Pi 3 is not detected correctly in the latest "Deploy Control SL 4.14.0.0" : Linux/ARMHFv7 unknown container technology. 1) The Communication Tab, device information section shows podman technology as DETECTED. 2) The Runtime Deployment menu message says: "unknown container architecture" 3) The pulldown window under the deployment tab doesn't show the options for ARMHF Virtual Edge SL and ARMHF Virtual Control SL. I hope you can fix this soon and keep up the great work!
Last updated: 2024-12-15

Post by dogulas on OPC UA C# client connecting to OPC UA CODESYS server ^{CODESYS Forge talk (Post)}
Ok, for the sake of completeness in case anyone else has this problem. I can tell you that what finally worked for me was to change the line: // create an ExtensionObject to wrap the value to be written ExtensionObject extensionObject = new ExtensionObject( new ExpandedNodeId("GVL_StructA", 5), structAData ); to: // create an ExtensionObject to wrap the value to be written ExtensionObject extensionObject = new ExtensionObject( new ExpandedNodeId("GVL_StructA|defaultbinary", 5), structAData ); I'm sure there are many other problems that could cause this very generic error, but this was my problem.
Last updated: 2024-12-30

Post by pernockham on Inheritence of struct, ^{CODESYS Forge talk (Post)}
Interesting, thanks! Didnt know about ANY before, and will sure find a use-case for it. Im not sure it will help me here though, it seems to me that an ANY will not accept a string assignment? I actually think that the "ALIAS" should work, that was a hard found error. I had a fair bit of scratching my head looking for misdirected pointers before I understood what was (not) happening. I will use the work-around of individual structs instead.
Last updated: 2025-03-08

Post by pistola on How to change font and font color rectangle/or related object ^{CODESYS Forge talk (Post)}
Here is the help sections for visual elements rectangle. https://content.helpme-codesys.com/en/CODESYS%20Visualization/_visu_elem_rectangle.html Under "Font Variable" there is "Color" which is a Dword, you can make a variable that changes colour within your code to the color needed. Note the format for the Dword variable is: colorVariable := 16#TTRRGGBB Where: TT = Transparency 00-FF RE = Red 00-FF GG = Green 00-FF BB = Blue 00-FF https://content.helpme-codesys.com/en/CODESYS%20Visualization/_visu_animate_color.html
Last updated: 2025-03-17

Post by krisj on ScriptEngine POU property Get and Set accessor. ^{CODESYS Forge talk (Post)}
Hey! I am trying to generate a function block with properties from a list with script engine. Codesys/ScriptEngine creates both the Get and the Set accessor. I cannot find a way to delete the Set method/accessor. Anyone encountered the same problem or have a solution for this? for prop_name, prop_type in list: property = pou.create_property(prop_name, prop_type) get = pou.find("Get", recursive=True)[i] get.textual_declaration.replace("") get.textual_implementation.replace(prop_name + " := " + struct_name + "." + prop_name + ";") set = pou.find("Set", recursive=True)[i] set.textual_declaration.replace("") set.textual_implementation.replace("") i += 1
Last updated: 2025-03-17

Post by nz-dave on Ethernet/IP Scanner Exception ^{CODESYS Forge talk (Post)}
Hi Trusty-Squire, just seen you post , thanks for the reply. I was out on site the other day as it had done it again and changed a few things like cycle time etc. plc load is only 7% at its highest. I took a few screenshots while i was there to add to this post. its been up for about a week now but seems to happen at random every couple of weeks. fingers crossed!
Last updated: 2025-03-19

Post by atone on Set DeviceID of an IO-Link Sensor at Runtime ^{CODESYS Forge talk (Post)}
I need to be able to change (set) the DeviceID of an IO-Link sensor (see DeviceID.png) at runtime. I tried with both ProfinetCommon.PN_PortConfiguration and ProfinetCommon.IOL_PortConfiguration, but I get an error for both when I try to read the port configuration (see PN_PortConfiguration.png). Does one of those FBs is the right one for my purpose? Do I possibly make a mistake when assigning the parameter IOLD_ID/IOLM_ID?
Last updated: 2025-03-19

Post by dkugler on Beckhoff EL6652-0010 with Codesys ^{CODESYS Forge talk (Post)}
we use successful for many years the KEB MFI terminal for Profinet, EtherCAT, Ethernet/IP,... You'll need a EtherCAT Coupler as "head" from KEB, Kendrion or Berghof. It's all the same board inside: https://www.kebamerica.com/products/ethercat-bus-coupler/ Or the coupler with 16Di/Do integrated: https://www.kebamerica.com/products/ethercat-digital-io-module/ last year I got a EK1100 with EL6731 Profibus treminal runnig. But it was a lot of reverse engineering and thinkering in Codesys and TwinCAT to be done, to get it up, fulfilling my needs. Good luck!
Last updated: 2025-03-25

Post by johnbomb on Ignore Dependencies When Loading Package? ^{CODESYS Forge talk (Post)}
I'm trying to load a .package into Codesys 3.5.21, but the package is intended to only work with Codesys 3.5.18.0 and is configured with dependencies on the specific versions of other packages included with 3.5.18.0, and 21 has newer versions so the package will not install. I would like to install the package anyway to try and get things working on a newer Codesys version, since for some reason the installer for .18 errors out and doesn't fully work in my environment, but .21 seems to work fine.
Last updated: 2025-04-01

Sort by relevance or date