Post by rckalex on Data Source Limit ^{CODESYS Forge talk (Post)}
There appears to be a limit to the number of OPC Servers that can be connected simultaenously. 1-10 work but adding an 11th makes one of the previously linked ones unavailable. Is this a soft setting that can be adjusted? Using 3.5.18.30 on Win x64
Last updated: 2024-03-06

Post by ph0010421 on Sending Sequential Modbus TCP Packets ^{CODESYS Forge talk (Post)}
Hello You'll need to write a proper sequence to send, then wait for confirmation, and then move on to the next step. Use the CASE statement in ST. It's perfect for creating a sequence.
Last updated: 2024-03-08

Post by trycyclepower on Only single ehternet ip drive is communicating ^{CODESYS Forge talk (Post)}
Hi all, I have two ethernet IP drives not communicating together. If I disable one, then other one starts working. ENIPScnannerIOTak cycle is setup as 20ms. Also, PLC updating variables setting is on.
Last updated: 2024-03-08

Post by niallel on How to change bHiresMode ^{CODESYS Forge talk (Post)}
Thank you so much for the reply. The motor is a rotary connected to a linear actuator. So would I set it up as in the attachment screenshot?
Last updated: 2024-03-12

Post by fless on How to change bHiresMode ^{CODESYS Forge talk (Post)}
Hi, you should see 2 input fields in the scaling tab of your linear axis: increments and units in application just set increments to 10 and units in application to 366
Last updated: 2024-03-12

Post by wmoon on Licensing info not available. ^{CODESYS Forge talk (Post)}
That command can't excute on my device. I installed CODESYS into Hilscher's product using container Here is the Docker file what I used. I'm not sure if this docker file have a problem. If it have a problem, please let me know how to download the files into my device using ftp server. FROM arm64v8/debian:11.6 RUN apt-get update RUN apt-get install -y wget sudo unzip libusb-1.0-0-dev procps ENV CDS_VERSION "4.10.0.0" ENV EDGE_VERSION "4.10.0.0" ENV URL "https://store-archive.codesys.com/ftp_download/3S/LinuxARM64/2302000039/$CDS_VERSION/CODESYS%20Control%20for%20Linux%20ARM64%20SL%20$CDS_VERSION.package" ENV EDGE_URL "https://store-archive.codesys.com/ftp_download/3S/EdgeGatewayLinux/000120/$EDGE_VERSION/CODESYS%20Edge%20Gateway%20for%20Linux%20$EDGE_VERSION.package" RUN wget --output-document=/tmp/codesys.package $URL && \ unzip -p /tmp/codesys.package 'codemeter.deb' > /tmp/codemeter.deb && dpkg -i /tmp/codemeter.deb && \ unzip -p /tmp/codesys.package 'codesyscontrol.deb' > /tmp/codesys.deb && dpkg -i /tmp/codesys.deb RUN wget --output-document=/tmp/edge.package $EDGE_URL && \ unzip -p /tmp/edge.package '*arm64.deb' > /tmp/edge.deb && dpkg -i /tmp/edge.deb EXPOSE 11740 1217 11743 ENTRYPOINT ["/bin/sh", "-c" , "/etc/init.d/codesyscontrol start && /etc/init.d/codesysedge start && tail -f /dev/null"]
Last updated: 2024-03-20

Post by k4zz on Static Code Analysis ^{CODESYS Forge talk (Post)}
The Solution. For Projects: #check all pool objects system.commands["project", "buildactiveapp"] #run static analysis system.commands["staticanalysis", "run"].execute() For Libraries: #check all pool objects system.commands["project", "buildactiveapp"] #run static analysis system.commands["staticanalysis", "runforlibrary"].execute()
Last updated: 2024-03-20

Post by doli on Table selected row ^{CODESYS Forge talk (Post)}
Hello. So I have two visualizations. In my main visualization I have a table and in the second one I have a dialog. When I select a row I want that dialog to open. How can I do this? Thank you!
Last updated: 2024-03-20

Post by timvh on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
You should only open de COM port once and then leave it open. This hCom should not keep on incrementing. (off course when you are done communicating, you need to close the COM port)
Last updated: 2024-03-22

Post by andrew-budaiev on Properties feature request ^{CODESYS Forge talk (Post)}
Can I leave a feature request here? If it's possible to do now, but I don't know how, please forgive me. It would be good if the following were possible: Ability to copy/paste properties. Ability to tab through properties.
Last updated: 2024-03-26

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by dagsupport on CAA SerialCOM - hCom Reset max value 1023 ^{CODESYS Forge talk (Post)}
Hi TimH Thanks for the information, I thought that was the case so have stepped through the code and found an error that wasn't closing the port, therefore hCom was increasing. Thanks
Last updated: 2024-03-28

Post by jetme on Rampup and rampdown ^{CODESYS Forge talk (Post)}
i'm using FB Ramp_INT function to ramp my pump up and down but I will like to ramp up at a different time and also ramp down at a different time. How can I do that.
Last updated: 2024-03-28

Post by andrew-budaiev on Tank Level Display ^{CODESYS Forge talk (Post)}
If I want to display level in the tank, what's usual approach? Is there tank or vessel element I can use? I see there is bar display, but I can't make it fill the shape I need.
Last updated: 2024-04-03

Post by simonh on Datasource OPC UA Client error ID:7012 ^{CODESYS Forge talk (Post)}
Hello, did you find the solution for the communication?Has the communication between the two been successful? if yes, can you please share me your solution since i have similar issue now. Thanks.
Last updated: 2024-04-04

Post by saugat10 on Cannot find existing placeholder ^{CODESYS Forge talk (Post)}
I have installed a library VisuUtils. As you can see in the picture it cannot find the reference to System_VisuElemBase though it is indeed present. How can i resolve this issue?
Last updated: 2024-04-08

Post by squiggleypuff on Can't Add New Version of Modbus TCP Master ^{CODESYS Forge talk (Post)}
Turns out Modbus was working despite the pre-compiler errors; I was reading the wrong addresses of the slave device, which was why I was seeing all 0s. Thanks for ignoring me.
Last updated: 2024-04-09

Post by vincentger on v3.5 SP19 - Modbus TCP Devices - Channel Limit? ^{CODESYS Forge talk (Post)}
Any resolution on this? I have currently 75 channels in my project that i brought up from SP18, which means i am 65 Channels above the new limitation?
Last updated: 2024-04-09

Post by januar on Trend recording build error - the variable "arrTraceMgrVariablesImpl" is too large ^{CODESYS Forge talk (Post)}
Hi Adel, No, I just update all to the latest version and it is working. Kind regards, Januar
Last updated: 2024-04-10

Sort by relevance or date