Post by muhq on Profinet connection to Siemens CP343-1 Lean (IO-Device/Slave) ^{CODESYS Forge talk (Post)}
Hi, I am quite new to Codesys and I try to do a Profinet connection to an Siemens PLC (315-2DP) with CP343-1 Lean Modul. I already configured the Siemens PLC, exported the GSDML. Then I added a new project in Codesys, added following moduls: - Ethernet - PN_Controller - Imported Profinet Device via GSDML importer When I start the programm everything looks fine but I always get the message "Stopped Profinet" and no data is available This is only for a small test. Therefore I start to do that on a Windows 10 with Development System. Later I will try to realize this on Raspberry. Ethernet Adapter is configured (192.168.1.1 / 24) Firewall deactivated WinPCap is installed S7-Station seems to be found ('fuadazenzitest') Can please somebody help me?
Last updated: 2023-08-26

Post by janber0206 on Gateway doesn't come online, regarding a working internet connection ^{CODESYS Forge talk (Post)}
Solved (see comment) Setup: Kunbus RevPi Connect+ (a raspberry based PLC) Codesys runtime package: 4.5.0.0 (raspberry, armhf) based on Codesys V3.5.18.20 Edge Gateway: 4.5.0.0 (edgearmhf,armhf) EN: The edge-gateway was added over a year ago to the automation server. I now need to make a few changes to the Codesys software, but the Pi is not showing as online in the Automation Server. Internet connection is established, I have remote access to the Pi via RealVNC. Anyone have an idea how I can solve this? Some screenshots added. DE: Ich muss nun ein paar Änderungen an der Codesys-Software vornehmen, aber der Pi wird im Automation Server nicht als online angezeigt. Die Internetverbindung ist hergestellt, ich habe über RealVNC Fernzugriff auf den Pi. Hat jemand eine Idee, wie ich das Problem lösen kann?
Last updated: 2023-10-26

Post by cedriclee on RaspberryPI reconnection error ^{CODESYS Forge talk (Post)}
"Hello, I'm Cedric Lee, a PLC engineer based in Korea. I'm reaching out about an ongoing issue with the connection when attempting to control Beckhoff modules using Raspberry Pi with CODESYS for the first time. I use CODESYS to target the Raspberry Pi's IP, install version 4.10.0.0 of the CODESYS Runtime Package, and upon pressing Start in the Runtime, the target connects to the Raspberry Pi. However, within about a minute, an error window appears, stating 'no connection to the device. please rescan your network,' leading to the disconnection of the target. This cycle repeats. I've attached some pictures for your reference. I'm using CODESYS Development System V3, Raspberry Pi 4 Model B (installed as 64-bit), and Beckhoff EK1100 modules. If anyone has a solution to this issue, please help. Your assistance is greatly appreciated."
Last updated: 2024-01-11

Post by sumit on Not able to see input data coming from eip adapter on codesys ^{CODESYS Forge talk (Post)}
dhumphries, I changed the datatype this time from BYTE to USINT (because that's what my adapter is sending: array of uint8_t). The text "New Help String" you saw in previous screenshots is just the description of the input/s (it can be anything). I also looked into the logs (see attached) for that ! sign next to the device, I found that connection is being timeout. I tried some suggestions from online such as increase the RPI but still got connection timeout issue, also by changing the datatype, I still don't see incoming data from the adapter, although its visible on wireshark. thanks,
Last updated: 2024-03-07

Post by damian177 on Problem with downloading OPC UA tags by Data Source Manager ^{CODESYS Forge talk (Post)}
Hi, In Codesys V3.5 SP20, using Data Source Manager I am trying to connect to the OPC UA server and receive tags from it. The connection is ok, but the Codesys have a problem with downloading Tags group. The window (downloadingTags.jpg in attachement) never stop. After waiting for a while, I disconnect the connection and only the Server group remains downloaded, with OPC UA server diagnostic data (and this is read in Codesys). Of course, I tried connected via another OPC UA client : UaExpert , and everything works as it should, all tags are downloaded (Uaexpert.jpg screen). Has anyone on the forum encountered the OPC UA client configuration in Codesys? Is it possible to manually request the appropriate tags from the OPC server for reading in Codesys?
Last updated: 2024-09-03

Post by dsa28 on OPC UA subscriber not operational ^{CODESYS Forge talk (Post)}
Hello All, Hopefully I can get some help configuring an OPC UA subscriber in a CODESYS runtime in a Raspberry Pi 5 that tries to retrieve data from an OPC UA publisher (in this case running in a TwinCAT system). I tried to follow the steps described in the page to implement the OPC UA subscriber: https://content.helpme-codesys.com/en/CODESYS%20Examples/_ex_opcua_pubsub.html Seems that the example provided was created with version 3.5.16.0. Now with version 3.5.20.20 is not possible to open the complete project neither convert it. Anyway, after configuring all IPs and ports used in the OPC UA connection function block but the connection state always shows DISABLED. Can someone help me to do the proper configuration of the OPC UA subscriber? Many thanks in advance.
Last updated: 2024-10-22

Post by ltrinta on AWS IoT Core connection using AWS certificates ^{CODESYS Forge talk (Post)}
Hi there I want to know if there is possibility to connect a CODESYS application to AWS IoT Core using the certificates owneds by AWS. In the examples of CODESYS using AWS IoT Core library, we need to generate a local certificate and update it to AWS IoT Core. I want to use AWS IoT Core certificates. Regards, Leonardo
Last updated: 2023-09-28

Post by turndapage on Can't Add Symbol Configuration ^{CODESYS Forge talk (Post)}
I've got a Weintek HMI with CodeSYS built-in. I've got it connecting to CodeSYS and downloaded. The connection guide says I need to add a symbol configuration by right-clicking on the application and adding it, but it does not show up in the available objects. Is there something else I have to do to create a symbol configuration object?
Last updated: 2023-10-04

Post by snhatton on OPC UA: How to change NodeId ?! ^{CODESYS Forge talk (Post)}
You can change the node id by adding the following to /etc/CODESYSControl.cfg: [CmpOPCUAProviderIecVarAccess] CustomNodeName=MyPLC123 Then restart the runtime and the new Node name will appear with the connection. I don't know if it's possible to remove the |var| from the name. I hope this helps!
Last updated: 2023-12-11

Post by dhumphries on IO link on IFM AL133x only single digital input on a channel ^{CODESYS Forge talk (Post)}
Try changing the port mode to digital input for each port you want to have 2 inputs in the connection settings for the device. I've successfully used ports for inputs on an AL1920 this way, I think the procedure should be the same for an AL1332.
Last updated: 2023-12-30

Post by peter-skokanek on Rpi install runtime licence on SP13 ^{CODESYS Forge talk (Post)}
Hi, I have an older project which has been running for years. Unfortunately I have to replace current Raspberry. I repplaced it by new rpi 3 with newest 32 bit Raspberry OS. I oredered a new runtime licence. When I try to activate it, the connection to target is interrupted immediatelly after press next button in the last step of instalation.
Last updated: 2024-01-08

Post by dhumphries on WAGO PLC 200 750-8216 Ethernet connection to Codesys 3.5 ^{CODESYS Forge talk (Post)}
make sure the PLC and the programming PC have IP addresses that are on the same subnet, you'll have to know the default address of the PLC or you may need to connect to it with a special cable and use a software tool to set the IP address.
Last updated: 2024-02-06

Post by camilloo on Control for Linux SL on Ubuntu Core ^{CODESYS Forge talk (Post)}
Hello, Has anyone tried running CODESYS Linux on Ubuntu Core? I'm having problems installing the runtime. The connection to UC cannot be established. I used the instruction: https://content.helpme-codesys.com/en/CODESYS%20Control/_rtsl_linux_public_key_authentification.html I can connect to UC using SSH (putty, shell). Codesys can't. Do any of you have an idea?
Last updated: 2024-02-24

Post by timvh on when going online, stuck on "Syncing file "visuelemsdatetime.tl_datetime.txt" ^{CODESYS Forge talk (Post)}
I don't know the root cause... But what could help to continue when it seems to hang, is stop the CODESYS (communication) Gateway. Go to the Windows SysTray, find the icon for the Gateway and then stop it and start it again. This will interrupt the connection between CODESYS and your controller.
Last updated: 2024-03-05

Post by i-campbell on Not able to see input data coming from eip adapter on codesys ^{CODESYS Forge talk (Post)}
Hello, I think you can try to change the Connection from Multicast to Point to Point. Please also make sure your windows firewall is allowing the correct UDP ports inbound for ethernet IP. You might also need to increase the RPI, so it times out slower.
Last updated: 2024-03-07

Post by thysonfury on OPTO22 Groov Epic PR2 Modbus Comms Dropping out every 2 hours and 4 Mins ^{CODESYS Forge talk (Post)}
Hi after some assistance with an error on a Groov PR2 PLC. We have a few different communications set up as shown below: One Modbus TCP Slave Connection - ( Sending / Receiving Data from a PC ) Two Modbus TCP Master Connection - ( Reading Data from a UPS Panel and Reading Data Gas Chromatograph) One Modbus RTU Slave Connection 485 - (Reading Data from a fire and gas panel) One Modbus RTU Master Connection 485 - (Sending Data to a Telemetry Unit) All Licenses have been installed as per OPTO22 suggestions of the order below: Modbus TCP Master Modbus TCP Slave Modbus RTU Master Modbus RTU Slave When I check on License manager the RTU Master license seems to disappear on installing the RTU. (What ever reason I’ve been told this is “normal”). If I use Device License Read It will successfully read all the licenses correctly. Now the issue is every 2 hours and between 4. For what ever reason the communications seems to end and lock up for about 20 seconds. During this time even if I was logged into the PLC it would kick me off and I’d have to re type the password to enter. Most of the devices can handle this however the RTU flags up a communications failure at the SCADA and is raising alarms every 2 hours and 4 mins. We’ve had multiple people go through the code to check for anything obvious. Does anyone have any ideas?
Last updated: 2024-04-15

Post by thysonfury on OPTO22 Groov Epic PR2 Modbus Comms Dropping out every 2 hours and 4 Mins ^{CODESYS Forge talk (Post)}
Hi after some assistance with an error on a Groov PR2 PLC. We have a few different communications set up as shown below: One Modbus TCP Slave Connection - ( Sending / Receiving Data from a PC ) Two Modbus TCP Master Connection - ( Reading Data from a UPS Panel and Reading Data Gas Chromatograph) One Modbus RTU Slave Connection 485 - (Reading Data from a fire and gas panel) One Modbus RTU Master Connection 485 - (Sending Data to a Telemetry Unit) All Licenses have been installed as per OPTO22 suggestions of the order below: Modbus TCP Master Modbus TCP Slave Modbus RTU Master Modbus RTU Slave When I check on License manager the RTU Master license seems to disappear on installing the RTU. (What ever reason I’ve been told this is “normal”). If I use Device License Read It will successfully read all the licenses correctly. Now the issue is every 2 hours and between 4. For what ever reason the communications seems to end and lock up for about 20 seconds. During this time even if I was logged into the PLC it would kick me off and I’d have to re type the password to enter. Most of the devices can handle this however the RTU flags up a communications failure at the SCADA and is raising alarms every 2 hours and 4 mins. We’ve had multiple people go through the code to check for anything obvious. Does anyone have any ideas?
Last updated: 2024-04-15

Post by thysonfury on OPTO22 Groov Epic PR2 Modbus Comms Dropping out every 2 hours and 4 Mins ^{CODESYS Forge talk (Post)}
Hi after some assistance with an error on a Groov PR2 PLC. We have a few different communications set up as shown below: One Modbus TCP Slave Connection - ( Sending / Receiving Data from a PC ) Two Modbus TCP Master Connection - ( Reading Data from a UPS Panel and Reading Data Gas Chromatograph) One Modbus RTU Slave Connection 485 - (Reading Data from a fire and gas panel) One Modbus RTU Master Connection 485 - (Sending Data to a Telemetry Unit) All Licenses have been installed as per OPTO22 suggestions of the order below: Modbus TCP Master Modbus TCP Slave Modbus RTU Master Modbus RTU Slave When I check on License manager the RTU Master license seems to disappear on installing the RTU. (What ever reason I’ve been told this is “normal”). If I use Device License Read It will successfully read all the licenses correctly. Now the issue is every 2 hours and between 4. For what ever reason the communications seems to end and lock up for about 20 seconds. During this time even if I was logged into the PLC it would kick me off and I’d have to re type the password to enter. Most of the devices can handle this however the RTU flags up a communications failure at the SCADA and is raising alarms every 2 hours and 4 mins. We’ve had multiple people go through the code to check for anything obvious. Does anyone have any ideas?
Last updated: 2024-04-15

Post by koehler on Codesys 3.5.12 Module not Found ^{CODESYS Forge talk (Post)}
Hi there, I am getting troubles with a project. In the Hardware configuration I got some Lenze drives 9400. One of them got as status " Module not Found". Connection are good. ID Node of the Canopen network is also good. I don't find any reason for this status, nor any options to check.
Last updated: 2024-04-17

Post by andrej on Channel timeout CmpChannelMgr ^{CODESYS Forge talk (Post)}
Hello, I use Codesys RTE 3.5.16.5. If I connect to the PLC I often get the following message: (see printscreen) 1. Channel timeout CMpChannelMgr. 2. Closing connection CmpChannelMgr. Can you tell me, what the meaning of this is? What does the number 1250030,1220020 resp. c400:0a0a:015a:0301 refer to? I could find any information in the online help. Thanks a lot.
Last updated: 2024-05-08

Post by eschwellinger on connect IDE to plc that uses modem ppp ^{CODESYS Forge talk (Post)}
Which plc type is it? Easy connection is to install a Gateway on remote side - this is available for Windows and Linux devices Then just add a new Gateway in CODESYS (with the IP Adress of the remote device) -> then scan the plc via this new added Gateway
Last updated: 2024-05-21

Post by nano on Cant login to Rpi4 but can see it in codesys communications settings. ^{CODESYS Forge talk (Post)}
which ports in detail are configured. the search of the rts works via broadcast-messages, programming with tcp-port on p2p-connection woth port-hopping, handled by runtime after siccesfully handshake. look at this entry on forge https://forge.codesys.com/forge/talk/Runtime/thread/4078a2ed28/
Last updated: 2024-06-23

Post by docker on Webvisu client connection monitoring ^{CODESYS Forge talk (Post)}
Hi, i am interested in this thread and have tried a couple of the above examples in to determine remote webvisu access. I am having trouble getting the lastusage variable to refresh during runtime? It seems to only log the last usage at initialisation and that is it? how do i gain ongoing access to the time variable as the code is running? Thankyou.
Last updated: 2024-08-26

Post by damian177 on OPC UA Client ^{CODESYS Forge talk (Post)}
Hi, Today I ran OPC UA Client Example in 1.1.0.0 version. I opened example visualisation and I tried connected to my OPC UA Server. In first steps looks good but connection was terminate with error OpcUa_BadLicenseLimitsExceeded. I can't test OPC UA Client witohut CODESYS OPC UA Client SL license ? Regards
Last updated: 2024-08-30

Post by rajankkrs on Ethercat master softmotion lost connection ^{CODESYS Forge talk (Post)}
Dear Edwin, we are also facing similar problem of communication failure, FB3 error in servo drives. we tried all the suggestion by Kim but still we couldn't solve the issue. we uses Codesys 3.5 sp18 patch2, servotronix servo drives CDHD and crevis GN-9483. Any suggestion / input to solve the issue please. is anyway in codesys to reset the FB3 error? -Rajan
Last updated: 2024-10-07

Sort by relevance or date