Post by ch-user on WebVisu File Transfer Error ^{CODESYS Forge talk (Post)}
Try without / at first, just 'plcdata/csv_logs/yourcsvfile.csv'
Last updated: 2025-08-15

Post by andrax on CodeSys Raspberry pi I2C driver not found ^{CODESYS Forge talk (Post)}
Hi, Communication with the ADS1115 is actually simple. 1. write config 2. write address pointer 3. read conversation register The ADS1115 works like a multiplexer. This means that you do this individually for each channel that you want to read. e.g: Channel 1: write config > write address pointer > read conversation register Channel 2: write config > write address pointer > read conversation register Channel 3: write config > write address pointer > read conversation register Channel 4: write config > write address pointer > read conversation register then you start again from the beginning You can also omit individual channels or read only one. It doesn't matter. I have written the driver so that I can also use it on the TCA9548. The driver is from Stefan Dreyer. In your case, the driver works and communication with the ADS1115 is running. As you can see, the cfgWrong:=FALSE If you could not write or read data, cfgWrong:=TRUE; This means that either something is wrong with your ADS1115 or you have connected something incorrectly. Question: what voltage do you want to measure?
Last updated: 2024-11-08

Post by struccc on Problem Reading Registers via Modbus from non Codesys device ^{CODESYS Forge talk (Post)}
Hi, Might be a good idea first to try out the connection and the device with some handy software, like Modbus Poll. There you can see better, what's really going on... - Is it really connected? - What error code does it return? - Can it read from the register address? - Maybe try Input registers and Holding Registers - can make a difference - Sometimes register addresses are messed up: shifted +-1 (mixing of 2 standards) - Sometimes register addresses start with offset 30000, 40000 ... - Are you using the right protocol? - Is it RTU or TCP? Maybe ASCII? - Can even have a look at the data packets, etc... All this is easier to figure out first with some modbus utility... and then to set it up in CODESYS should not be an issue. P.
Last updated: 2025-03-09

Post by matt-purcell on Which Lib to use, connect to a socket with URL instead of IP address ^{CODESYS Forge talk (Post)}
Hello, I have a new project and I need to connect to a TCP socket using the URL instead of an explicit IP address, myendpoint@mydomain.com Which library is best suited for this? This is for a new enterprise project, the endpoint is a server in a datacenter running some real time application. We have big IP, it will automatically reassign the IP address to the backup server if a crash occurs so an explicit IP won't work for me. I've done this in RS logix, working now to migrate that code over to codesys. Thanks in advance!
Last updated: 2024-06-17

Post by malte on OPC UA multiple Endpoints ^{CODESYS Forge talk (Post)}
My CODESYS OPC UA server provides endpoints using both the hostname and the IP address. Connecting via the IP address works fine, but connecting via the hostname does not. The endpoint list shows both opc.tcp://<hostname>:4840 and opc.tcp://<ip>:4840. When using the hostname, the OPC UA client (UA Expert) fails to connect. Using the IP address connects without issues. Main goal is to conect via Python but opcua-asyncio seems to prefer the hostname. How can I configure CODESYS or my system so that the OPC UA connection via hostname also works properly or disable it completly? Running Codesys for PFC200 sl 4.18.0.0
Last updated: 2025-10-28

Reading from a file, a line of CSV values with CrLf at the end of the line. ^{CODESYS Forge talk (Thread)}
Reading from a file, a line of CSV values with CrLf at the end of the line.
Last updated: 2018-09-18

Post by i-campbell on MODBUS TCP REGISTERS CODESYS V3.5 ^{CODESYS Forge talk (Post)}
codesys is in hex and starts at 0 your other program is set to decimal and maybe starts at 0 or 1, I can't tell.
Last updated: 2024-10-12

Post by talhaali on Control Win one instance at a time ^{CODESYS Forge talk (Post)}
I want to open one instance of runtime to be opened at a time even I hit multiple times? How can I implement it?
Last updated: 2024-10-25

Post by talhaali on Control Win one instance at a time ^{CODESYS Forge talk (Post)}
I want to open one instance of runtime to be opened at a time even I hit multiple times? How can I implement it?
Last updated: 2024-10-25

Post by talhaali on Control Win one instance at a time ^{CODESYS Forge talk (Post)}
I want to open one instance of runtime to be opened at a time even I hit multiple times? How can I implement it?
Last updated: 2024-10-25

Post by talhaali on Control Win one instance at a time ^{CODESYS Forge talk (Post)}
I want to open one instance of runtime to be opened at a time even I hit multiple times? How can I implement it?
Last updated: 2024-10-25

Post by talhaali on Virtual and hardwired Keyboard together ^{CODESYS Forge talk (Post)}
Hi there, Is there any way I can use harwired and virtual keyboard at same time. There is an option to use either touhpad or keyboard in targetVisu. Is there any way that I can use both at same time?
Last updated: 2024-12-10

Is it possible to link an array of bits to an alarm group to show a lot of alarms at once? ^{CODESYS Forge talk (Thread)}
Is it possible to link an array of bits to an alarm group to show a lot of alarms at once?
Last updated: 2021-07-08

Post by nano on Library for arrays ^{CODESYS Forge talk (Post)}
habe a look at __new and __delete operators. have in mind that in this case u have a look at memory see https://help.codesys.com/api-content/2/codesys/3.5.15.0/en/_cds_operator_new/
Last updated: 2024-01-14

Post by pr0schwein on Driving the slave axis across master's zero point - caming ^{CODESYS Forge talk (Post)}
Is there a way to move the slave axis across the zero point of the master axis with variable start and stop points? For example: Slave start at 270° and end at 50°. thanks :)
Last updated: 2024-01-18

Post by davidbo on I2c write is BeforeWriteOutputs needed? ^{CODESYS Forge talk (Post)}
I have made an I2C library where writing happens by calling write8 I now see that I do not call BeforeWriteOutputs at all, however it seems to work data are sent at least for an hour. So is BeforeWriteOutputs needed
Last updated: 2024-02-07

Post by jetme on Rampup and rampdown ^{CODESYS Forge talk (Post)}
i'm using FB Ramp_INT function to ramp my pump up and down but I will like to ramp up at a different time and also ramp down at a different time. How can I do that.
Last updated: 2024-03-28

Post by davidbo on How to switch between dynamic IP address and dynamic? ^{CODESYS Forge talk (Post)}
Well. One can do that, I have found a python script which can modify /etc/dhcpcd.conf and I suppose there is a way I can execute it from CODESYS and it seems to be the only way
Last updated: 2023-11-08

Post by mondinmr on First IO address of a CAADiagDeviceDefault. ^{CODESYS Forge talk (Post)}
I have a device CAADiagDeviceDefault: IoConfig_Globals.Axis_A In our library, we perform introspection of the Etc_SlaveDiag. In that case, we have connectors, and by searching for them by address, I can find them in the IO mapping using the offset and size provided by EtherCAT. However, a Lenze i700 drive, instead of placing the IO mapping in the Etc_SlaveDiag device, places it in a sub-device CAADiagDeviceDefault. So, when I perform introspection, I cannot find the IO correspondences. Yet, in the CAADiagDeviceDefault, I do not find the connectors and cannot do the matching. Is there a way with a pointer or reference to a CAADiagDeviceDefault to obtain the address of the first input and the address of the first output? This is because we have our own motion library with many EtherCAT devices that automatically configure the mappings, but I can't manage to do so with the Lenze i700.
Last updated: 2024-08-22

Post by pablotorres on Dynamic Setting IP Address from IEC code ^{CODESYS Forge talk (Post)}
Hi! I have a problem, when I write Ethernet.Enable, I get an error ("Enable" undefined). Could you send me the program? I can't solve it, and I don't know if it's because I'm missing a library or some FB...
Last updated: 2024-09-30

Post by timvh on Modbus TCP & RTU with Control for Linux SL ^{CODESYS Forge talk (Post)}
Most likely your IP address is set to 172.... because you use a VPN connection to your device. Probably best to use the other Ethernet interface for your modbus communication.
Last updated: 2024-10-24

Post by fless on Help with __SYSTEM.VAR_INFO ^{CODESYS Forge talk (Post)}
to get the address just use ADR( ) variables defined in a VAR_IN_OUT block are references pointing to the passed variables. VAR_IN_OUT MyVar: bool; END_VAR VAR adrMyVar: __XWORD; END_VAR adrMyVar := ADR(MyVar);
Last updated: 2025-01-26

Post by chrisdeloglos on Network Variables not updating ^{CODESYS Forge talk (Post)}
Thanks for the comment. I'm using Weidmueller UC20-WL2000-AC's and changing the broadcast address to match the current subnet this worked for me as well!
Last updated: 2025-01-27

Post by timvh on VisuElems.cmpDynamictext.DynamicTextGetTextW returns pointer to empty string ^{CODESYS Forge talk (Post)}
Try this: VAR sTextList : STRING; END_VAR sTextList := 'NameOfTheTextList'; // call to the function with the address of the string variable which contains the name of the textlist : ... ADR(sTextList), ....
Last updated: 2025-02-07

Post by alexanderraab on EtherCAT: How to change station-alias/ Slave address ^{CODESYS Forge talk (Post)}
Hello, i have the same situation to change the Station-Alias adress online by IEC-Code. Have someone an exsample for that?
Last updated: 2025-08-13

Sort by relevance or date