Post by olehmann03 on PFC200 - WAGO 750-8202 - MODBUS RTU ^{CODESYS Forge talk (Post)}
Hello, I’m working on implementing Modbus RTU communication with a Carel controller (CPCO). I want to use the front RS485 interface through the DB9 connector. The issue is that I can’t get the communication working correctly. Below are the steps I’ve done so far: Connected pins 3 and 8 from the DB9 connector to the +/- RX/TX terminals on the Carel side. In the PLC shell, I set serialmode to RS485. In WBM under Administration > Serial Interface > Assign owner of serial interface, I set the port to unassigned. In the device tree, I created Modbus_COM with the following settings: COM port: 1 Baud rate: 19200 Parity: None Stop bits: 1 Created a Modbus client on this COM interface in RTU mode. Under the status tab, I can see it is in running state. On the client, I created a Modbus server and set the Modbus address of my unit to 1. Defined a few channels as FC03 to read holding registers according to the Carel register map. I checked the communication with the Carel controller using a USB-to-RS485 converter connected to my PC, and communication works correctly there. In the status tab, I can see that the Modbus server is polling, but there is no response from the controller. I also tried multiple times swapping A/B lines on the Carel side, but it did not help. Do you have any suggestions on what else I should check?
Last updated: 2026-05-22

Post by timvh on ernesto881124 ^{CODESYS Forge talk (Post)}
You will need a USB to RS485 converter to connect the PC to the Modbus RTU Slave Device. In Windows this converter will be recognized as Serial COM poort (e.g. COM2, or COM3, see the windows device manager to find this out). Select this port in your CODESYS application. On the PC you need to use the CODESYS Control Win (SoftPLC) to run your application. It will not work in simulation mode, because then the Modbus Communication will not be activated.
Last updated: 2023-09-14

Post by vformanek on OPCUA Datasource, can not login... ^{CODESYS Forge talk (Post)}
Hello? I have a problem with datasource... I am trying to connect to a OPCUA server. I create a datasource, but I can not login into it. I need to use login credentials to login... Everything works fine in UAExpert, but in codesys I cant seem to get in properly using the login credentials... I have tried to configure the datasource initializer but seem to keep failing... Do I need to call it somewhere ? Will the find endpoints work with this configured to store my password ? !
Last updated: 2023-11-20

Post by pavanifm on Test a manager script (.tsd file{xml document}) not starting from Git CI heedlessly/ without ui ^{CODESYS Forge talk (Post)}
'--noUI' option of Command line interface for test manager test script not executing when triggered from CI as well as from Local PC however is it working for execution of python scripts from CLI. can we start codesys test manager scripts from CLI interface without any GUI in background process of windows? i can see simlillar questions asked but no answer yet. otherwise, what is the solution to built test automation framework using Test Manager & GIT CI/CD?
Last updated: 2024-08-07

Post by pavanifm on Test a manager script (.tsd file{xml document}) not starting from Git CI heedlessly/ without ui ^{CODESYS Forge talk (Post)}
'--noUI' option of Command line interface for test manager test script not executing when triggered from CI as well as from Local PC however is it working for execution of python scripts from CLI. can we start codesys test manager scripts from CLI interface without any GUI in background process of windows? i can see simlillar questions asked but no answer yet. otherwise, what is the solution to built test automation framework using Test Manager & GIT CI/CD?
Last updated: 2024-08-07

Post by pavanifm on Test a manager script (.tsd file{xml document}) not starting from Git CI heedlessly/ without ui ^{CODESYS Forge talk (Post)}
'--noUI' option of Command line interface for test manager test script not executing when triggered from CI as well as from Local PC however is it working for execution of python scripts from CLI. can we start codesys test manager scripts from CLI interface without any GUI in background process of windows? i can see simlillar questions asked but no answer yet. otherwise, what is the solution to built test automation framework using Test Manager & GIT CI/CD?
Last updated: 2024-08-07

Post by pavanifm on Test a manager script (.tsd file{xml document}) not starting from Git CI heedlessly/ without ui ^{CODESYS Forge talk (Post)}
'--noUI' option of Command line interface for test manager test script not executing when triggered from CI as well as from Local PC however is it working for execution of python scripts from CLI. can we start codesys test manager scripts from CLI interface without any GUI in background process of windows? i can see simlillar questions asked but no answer yet. otherwise, what is the solution to built test automation framework using Test Manager & GIT CI/CD?
Last updated: 2024-08-07

Post by thn-power on Codesys Communication Manger - Required information model version exists in the model repository but is not found ^{CODESYS Forge talk (Post)}
Hi. Thanks for the answer. I think I found your post on the Wago forum. I have tried installing all different nodeset versions of the opcfoundation.org/UA but neither work. Though I could not find the nodeset version called 15.09.2021 anywhere online. The opcfoundation repository only goes back to version 1.04.11 2022-03-29. Also wondering how I can generate a custom information model that only refrences the latest version of nodesets?
Last updated: 2024-09-19

Post by davidbo on RPI can system operation like rm in a shell have an impact on a Task cycle time ^{CODESYS Forge talk (Post)}
CODESYS Control for Raspberry Pi MC SL v4.4.0.0 CANopen_Manager 4.2.0.0 I did not call rm directly from my TASK-i2c, it was trough the attached python script. It is not always a problem happens, but sometimes a rm takes a long time. I reduced the amount of calls to logi2c.py but I don't understand why TASK-i2c sometimes can cause problems for TASK-CAN
Last updated: 2024-09-27

Post by davidbo on RPI can system operation like rm in a shell have an impact on a Task cycle time ^{CODESYS Forge talk (Post)}
CODESYS Control for Raspberry Pi MC SL v4.4.0.0 CANopen_Manager 4.2.0.0 I did not call rm directly from my TASK-i2c, it was trough the attached python script. It is not always a problem happens, but sometimes a rm takes a long time. I reduced the amount of calls to logi2c.py but I don't understand why TASK-i2c sometimes can cause problems for TASK-CAN
Last updated: 2024-09-27

Post by mascara on TouchScreen does not work in Webvisualization. ^{CODESYS Forge talk (Post)}
I am configuring a Lenovo M900 computer with CODESYS Control RTE SL 3.5.20.30. I use an Aoc E2272pwut LED 21.5 monitor. The touchscreen works perfectly in the Windows 10 PRO environment but does not work in the WebVisualization environment (Window opened at PLC startup). Does anyone know if it is necessary to configure any drivers in Win RTE? I am at your disposal for any questions. Thank you.
Last updated: 2024-11-11

Post by selim on Need help to get RS-485 signal in Cosesys . ^{CODESYS Forge talk (Post)}
Hello Mr./Ms., I invested Raspberry Pi lot of time to get the output from the raspberry PI5. But, i did not get the signal. I use a raspberry pi 5> RS485 can hat > Modbus RTU, Industrial 8-ch analog acquisition module >weight transmitter jy-s60> S-load cell. I did not able to receive the signal from Modbus RTU to Raspberry PI5 where I use the RS 485 serial connection.
Last updated: 2024-12-01

Post by smartcoco on Opaque NodeId in the OPC UA server ^{CODESYS Forge talk (Post)}
This seems to be because when creating 'OPC UA' with 'Communication Manager', the 'IdentifierType' of 'NodeId' cannot be configured as' String 'type. This issue is not an isolated case. For this issue, CODESYS seems to have not provided guidance to users on how to proceed. We can provide feedback on this issue in the 'My Question' section of the 'CODESYS Store' to make CODESYS take it seriously.
Last updated: 2025-01-10

Post by rmaas on STRING conversions to DWORD ^{CODESYS Forge talk (Post)}
Hi, The '' characters in Codesys are there only to indicate it is a STRING type. They are not actually added to the string, maybe you are adding them unintentionally in the concat function? You can send your data from Codesys to Hercules to verify... Another option is to send the data as an array of bytes instead of a string, with every byte representing 1 ASCII character. https://www.ascii-code.com/ This way you are 100% sure Codesys is not adding any unwanted characters.
Last updated: 2025-01-31

Post by imdatatas on TO_STRING operator not working for IMPLICIT ENUM ^{CODESYS Forge talk (Post)}
Hi Everyone, It is a very useful feature to be able to obtain the enum value as a string with the TO_STRING operator by defining {attribute 'to_string'}. However, unfortunately the same function does not work for IMPLICIT ENUMs. I hope that {attribute 'to_string'} behavior can also work for Implicit Enumeration data types in one of the upcoming Codesys versions. https://content.helpme-codesys.com/en/CODESYS%20Development%20System/_cds_pragma_attribute_to_string.html https://content.helpme-codesys.com/en/CODESYS%20Development%20System/_cds_datatype_implicit_enumeration.html Best regards, Imdat
Last updated: 2025-03-27

Post by sercan on Does G75 work when SMC_NCInterpreter is used? ^{CODESYS Forge talk (Post)}
When a G75 command is received in a SoftMotion+CNC project, SMC_NCInterpreter does not generate any error commands, but the command does not continue execution! There is information about SMC_NCDecoder in the documentation of the G75 command. Is this command only supported by SMC_NCDecoder? Can the G75 command be used with SMC_NCInterpreter? Forexample: G75 ; RUNNING G01 X$Settings.X$ Y$Settings.Y$ Z$Settings.Z$ ; - G75 ; - G01 X100.0 Y200.0 Z300.0 ; -
Last updated: 2025-05-09

Post by sercan on Does G75 work when SMC_NCInterpreter is used? ^{CODESYS Forge talk (Post)}
When a G75 command is received in a SoftMotion+CNC project, SMC_NCInterpreter does not generate any error commands, but the command does not continue execution! There is information about SMC_NCDecoder in the documentation of the G75 command. Is this command only supported by SMC_NCDecoder? Can the G75 command be used with SMC_NCInterpreter? Forexample: G75 ; RUNNING G01 X$Settings.X$ Y$Settings.Y$ Z$Settings.Z$ ; - G75 ; - G01 X100.0 Y200.0 Z300.0 ; -
Last updated: 2025-05-09

Post by sercan on Does G75 work when SMC_NCInterpreter is used? ^{CODESYS Forge talk (Post)}
When a G75 command is received in a SoftMotion+CNC project, SMC_NCInterpreter does not generate any error commands, but the command does not continue execution! There is information about SMC_NCDecoder in the documentation of the G75 command. Is this command only supported by SMC_NCDecoder? Can the G75 command be used with SMC_NCInterpreter? Forexample: G75 ; RUNNING G01 X$Settings.X$ Y$Settings.Y$ Z$Settings.Z$ ; - G75 ; - G01 X100.0 Y200.0 Z300.0 ; -
Last updated: 2025-05-09

Post by sercan on Does G75 work when SMC_NCInterpreter is used? ^{CODESYS Forge talk (Post)}
When a G75 command is received in a SoftMotion+CNC project, SMC_NCInterpreter does not generate any error commands, but the command does not continue execution! There is information about SMC_NCDecoder in the documentation of the G75 command. Is this command only supported by SMC_NCDecoder? Can the G75 command be used with SMC_NCInterpreter? Forexample: G75 ; RUNNING G01 X$Settings.X$ Y$Settings.Y$ Z$Settings.Z$ ; - G75 ; - G01 X100.0 Y200.0 Z300.0 ; -
Last updated: 2025-05-09

Post by sercan on Does G75 work when SMC_NCInterpreter is used? ^{CODESYS Forge talk (Post)}
When a G75 command is received in a SoftMotion+CNC project, SMC_NCInterpreter does not generate any error commands, but the command does not continue execution! There is information about SMC_NCDecoder in the documentation of the G75 command. Is this command only supported by SMC_NCDecoder? Can the G75 command be used with SMC_NCInterpreter? Forexample: G75 ; RUNNING G01 X$Settings.X$ Y$Settings.Y$ Z$Settings.Z$ ; - G75 ; - G01 X100.0 Y200.0 Z300.0 ; -
Last updated: 2025-05-09

Post by felipemsgarcia on Edge Gateway online, but PLC is not online ^{CODESYS Forge talk (Post)}
Hi Edwin, The PLC is already in the automation server so nothing happens when I scan the network, however the PLC show offline (not connected). Please see logs below. [CmpLog] Logger.0.Name=codesysedge.log Logger.0.Filter=0x0000000F Logger.0.Enable=1 Logger.0.MaxEntries=100000 Logger.0.MaxFileSize=1000000 Logger.0.MaxFiles=1 Logger.0.Backend.0.ClassId=0x00000104 ;writes logger messages in a file Logger.0.Type=0x314 ;Set the timestamp to RTC Thank you!
Last updated: 2024-01-09

Post by thomas-moba on "sudo"-Befehle über die Funktion "SysProcessExecuteCommand2" ^{CODESYS Forge talk (Post)}
Hello, I need to execute "sudo" commands via CoDeSys 3.5 SP 19 P5 using the "SysProcessExecuteCommand2" function. Commands without sudo are no problem, but as soon as sudo is used in a .sh or a single command, it does not work. Command=AllowAll is entered under "SysProcess" in CODESYSControl.cfg. Nevertheless it does not work. Does anyone know what the problem could be? Greetings, Thomas
Last updated: 2024-02-01

Post by mp9876 on Device User Logon ^{CODESYS Forge talk (Post)}
Just adding some info regarding the issue above. Logged onto the project using dev3og5 user (see screenshots); appeared to be ok although when attempting to logon to the device message says 'currently not authorized to perform this operation on the device' (screenshot). If user dev3og5 has same permissions as Owner user; why would it not be authorized. I am at a loss; any assistance would greatly be appreciated. Thank you Mike
Last updated: 2024-03-16

Post by yongchaow on Can't connect to Device Raspberry Pi 4 from CODESYS IDE V3.5 SP19 ^{CODESYS Forge talk (Post)}
Hi, eschwellinger, I have the same problem, but I can not resolve the problem following this forum. There are my situation: pi@RevPiXXXX:~ $ uname -a Linux RevPiXXXX 5.10.120-rt70-v7l #1 SMP PREEMPT_RT Thu, 28 Jul 2022 10:36:48 +0200 armv7l GNU/Linux After "top": It looks like runtime is not running. One more piece of information to refer to, when I reboot the device it is possible to scan the device. Looking forward your reply.
Last updated: 2024-04-25

Post by eschwellinger on Raspberry PI 5 not working ^{CODESYS Forge talk (Post)}
there is a new problem with latest bootloader version. The problem seems to be: Version from2024-04-20 does not work-> 2024-01-15 version works the workaround is a rollback to January version: cp /lib/firmware/raspberrypi/bootloader-2712/stable/pieeprom-2024-01-15.bin ./pieeprom.bin rpi-eeprom-config pieeprom.bin > bootconf.txt rpi-eeprom-config --out pieeprom-new.bin --config bootconf.txt pieeprom.bin sudo rpi-eeprom-update -d -f ./pieeprom-new.bin sudo reboot
Last updated: 2024-04-29

Sort by relevance or date