Post by spiessli on Softmotion axis to CANopen Maxon IDX drive ^{CODESYS Forge talk (Post)}
Just verified the behaviour. Still is the same. It should be attached here. But I also tried the DCF-file with the axis in the lab with the real drive: The MC_Power block never goes out of busy. Had not time to investigate further, though.
Last updated: 2024-01-08

Post by florian on Stepper Drive with Ethercat ^{CODESYS Forge talk (Post)}
Codesys has a motion libraries (SoftMotion), but you need to buy a licence keys for them to work. the most basic one is SoftMotionLight. you just have to select your drive in the device view and add a SoftMotionLight CiA402 axis. then the library is added to your project. You can use the SML_* motion FBs and configure the axis now.
Last updated: 2024-03-22

Post by installwhat on Tripod rotary coordinate is not correct with right hand rule ^{CODESYS Forge talk (Post)}
https://www.instructables.com/Work-Coordinate-System/ https://www.researchgate.net/figure/The-WCS-Axis-follows-the-Right-Hand-Rule-Left-Where-the-Z-Axis-Points-Towards-the_fig1_288835535#:~:text=Hwa%20Jen%20Yap-,The%20WCS%20Axis%20follows%20the%20Right%20Hand%20Rule%20(Left)%20Where,tool%20relative%20to%20the%20WCS. https://help.autodesk.com/view/ACDMAC/2025/ENU/?guid=GUID-02A08BCD-B4E5-4068-9932-810EF3049218
Last updated: 2024-06-23

Post by abuckie on Getting raw value as full resolution for ADS1115 ^{CODESYS Forge talk (Post)}
I just found this and I am getting a value larger than 16 bit, around 81000 something. I am reading a 5 volt value and I am using level shifters for the i2c bus. This is how I have the channel configured: ADS1115.usiAddress := 16#48; ADS1115.ChannelConfigs[0].Active := TRUE; ADS1115.ChannelConfigs[0].PGA := FSR_6144mV; ADS1115.ChannelConfigs[0].InputMux := Single_0; RawAnalogValue := ADS1115.Channels[0].Value; It looks like every value is a multiple of 3. Any idea where to look to fix this? I think i found what I want to change in UpdateChannels Channels[FChannelNo].Value := INT_TO_REAL(WORD_TO_INT(LValue) * GetFullScaleRange(ChannelConfigs[FChannelNo].PGA)) / 2048.0; I try to edit it but I can't, sorry if this is a basic question, I am new to CODESYS.
Last updated: 2025-05-22

Post by konstantin on Lenze i950 Servo and WAGO PFC200 ^{CODESYS Forge talk (Post)}
Hello, In our workshop we have a Lenze i950 servo drive that has an EtherCAT bus and CiA402 compatibility. The WAGO is PFC200 750-8212 and as per documentation it has built-in license for SoftMotion Light functionality. It is not capable of supporting the full SoftMotion functionality like gearing and synchronizing. I added the EtherCAT esi files from Lenze and the EtherCAT master does see the drive, then I added a SoftMotion Light Axis object. The problem is that I can only energize the axis, I cannot execute any other commands. I set the positive and negative torque limits from the PDOs to 200% and when I try to move the axis by force it does not move back to its original position. I use the SML function blocks from the PLCOpen library and the error from the function blocks is that the op mode cannot be changed. Then I tried using a standard SoftMotion axis object and everything works fine, except the MC_Home function block. The axis moves back to its position when forced out of it. I follow this guide from Lenze - Lenze i950 CODESYS V3 What could cause this issue with the SoftMotion Light axis object? Best Regards Konstantin Kolev
Last updated: 5 days ago

Post by fmbrew-rob on Licensing info not available. ^{CODESYS Forge talk (Post)}
Was there ever any resolution to this? I am using Virtual Control SL on a ProxMox setup, and I can't get the license installed. I get the same errors reported above.
Last updated: 2024-09-21

Post by amy123 on CSV Utility CANNOT_OPEN_DIRECTORY ^{CODESYS Forge talk (Post)}
That solved it, thank you for the swift resolution! :) It would be fantastic ,if bandwidth permitting, the placeholder 'C:/temp' could be updated to 'C:\Program Files\CODESYS 3.5.19.60\GatewayPLC'. Anyway, thanks again for your assistance!
Last updated: 2024-02-14

Post by vincentger on v3.5 SP19 - Modbus TCP Devices - Channel Limit? ^{CODESYS Forge talk (Post)}
Any resolution on this? I have currently 75 channels in my project that i brought up from SP18, which means i am 65 Channels above the new limitation?
Last updated: 2024-04-09

Post by kevinm on Programmatically change Tappet on a cam ^{CODESYS Forge talk (Post)}
I am considering using a SoftMotion cam and tappets to activate functions on a machine - for example, triggering a pneumatic valve. I need the ability to change the actuation point (tappet "X" location) from the HMI during machine commissioning. Is there a way to change the "X" value of a tappet programmatically?
Last updated: 2025-04-01

Post by ioannis-a on OPC UA: How to change NodeId ?! ^{CODESYS Forge talk (Post)}
Same question
Last updated: 2023-11-29

Post by talhaali on Persistent / Programme change ^{CODESYS Forge talk (Post)}
Hi, did you get any solution for this.
Last updated: 2024-09-10

Post by ricola on Change default node Id name on PFC200 OPC UA ^{CODESYS Forge talk (Post)}
so great !! thanks for this
Last updated: 2024-10-10

Post by kevinm on Programmatically change Tappet on a cam ^{CODESYS Forge talk (Post)}
Thanks so much. That gives me what I need.
Last updated: 2025-04-02

Post by timvh on password policy ^{CODESYS Forge talk (Post)}
On your device, change the setting in CODESYSControl_User.cfg: [CmpUserMgr] SECURITY.UserMgmt.PasswordPolicy=DISABLED
Last updated: 2025-09-10

Post by niallel on How to change bHiresMode ^{CODESYS Forge talk (Post)}
That's brilliant, thanks so much for all your help.
Last updated: 2024-03-12

Post by astutoski on No Motion with SM3_RaspiStepper (GPIO 23/24 Show No Pulses) ^{CODESYS Forge talk (Post)}
Hi everyone, I’m completely new to CODESYS and have been teaching myself. And i Want to control an Axis using SM3RaspiStepper. Following the example on the RaspiStepper home page, I set up an axis through a POU and tied the SMC_StartupDrive (Visu) template to my axis instance (sud). Unfortunately, the motor never moves and I don’t see any pulses on the PULSE pin (GPIO 23). Hardware -Raspberry Pi 4 B -Nema 17 stepper motor -A4988 stepper driver (EN pin permanently tied to GND) Software / Runtime -CODESYS 3.5 SP21 Patch 1 – Raspberry Pi runtime (demo) -SoftMotion in demo mode -Package: SM3_RaspiStepper 0.0.0.6 Axis parameters: Pulse pin GPIO 23 Direction pin GPIO 24 Enable pin 0 (unused) Disable pin 0 (unused) Whether I start the axis from the visualization template or through Online Config Mode, the motor never spins. In Online Config Mode I press Power → the state changes from Standstill to Discrete_Motion, but the motor shaft is still locked and no step pulses appear on GPIO 23 (checked with a scope). I can provide screenshots of the Visualization, PLC logs, or wiring pictures if that helps. Any ideas on what I might be missing? Happy to provide screenshots, project files, or scope captures if that helps. Thanks in advance!
Last updated: 2025-06-25

Post by axilleas on SMC_Interpolator + SMC_controAxislbyPos ^{CODESYS Forge talk (Post)}
dear all I am working on a very generic gantry system (virtual drives + win v3 control) reading gcode from external file. In order to stop the interpolator function from running when gaps are detected, SMC_controlAxisByPos FB has the bStopIpo output which according to the manual is connected to the Interpolator's bEmergencyStop. Lets assume that the axis are parked in position X1000 Y1000 and the initial G code movement is G00 X500 Y500. The normal behavior is to travel from the actual x1000 y1000 to G00 X500 Y500. The SMC_Interpolator always gets the X0 Y0 as the initial position, meaning that the bStopIpo is active until the axis are in X0 Y0 and the release the interpolator to set the new positions to X500 Y500. Is there a suggested method to solve this behavior? bonus question: I get a lot of bStopIpo during standard interpolation movements (not gaps). While working with virtual axis this is not a problem but when real axis are installed this will be an issue. What exactly triggers the bStopIpo output? Slow axis accelerations compare to Gcode defaults? Kind Regards
Last updated: 2024-02-05

Post by jonasz on Discontinuity of A/B/C axis movement. ^{CODESYS Forge talk (Post)}
Hi, My problem was related to the behavior of the modulo axis, but maybe you will find something useful from what I write. The solution lies in path processing. Codesys offers a G-code analysis tool. Insert a CNC object into the project. The CNC settings object will be added automatically. By inserting appropriate processing modules into the CNC settings object and parameterizing them, you can test the behavior of the axis. When the effect is satisfactory, remember to add the module from CNC settings in the correct order in the processing path. Each CNC machine case is different. You need to spend some time to get your design tailored like an Armani suit. Good luck.
Last updated: 2024-05-09

Post by konstantin on CAM Motion Recover after STO ^{CODESYS Forge talk (Post)}
Hello, one of the projects I work on is about a racetrack collator with two independent belts on it - two different servo motors. Both motors share the same mechanical frame and there is a train on a belt that collects items from the input conveyor. The way the motion is performed is the following - there is a virutal master axis and both real axis are synchronised with different cam motion profiles. The problem is when an STO is triggered on any of the slave axis, the synchronization process starts from position 0 of the slaves. How can I force the slaves to retain their current position until the master passes their position? Then the slaves should catch up with the master according to the profile, the slaves should not start synchronization from 0 position. Best Regards Konstantin Kolev
Last updated: 3 days ago

Post by etienneneu on Trend x-axis description incorrect display ^{CODESYS Forge talk (Post)}
Hello everyone, maybe someone can help me with the following problem. I wanted to insert a trend element in my visualization. The problem is that I have set fixed fonts with a scaling of 1.5 for the individual languages via the visualization manager. This setting means that I have this scaling in every element, which has been quite comfortable so far because I didn't have to set the individual properties in the text fields. But in the trend element, even if I select other font sizes or fonts in the element itself, this font is also overwritten and I get a label on the x-axis that is no longer displayed correctly. Is there a way to prevent the overwriting of the font properties in this element or similar behavior? I mean, I could change the font size of each element manually, but the Visu app is a bit larger and it would be easier to have another option. Best regards Etienne
Last updated: 2024-11-28

Post by teichhei on The selected container ... does not fit your ticket ^{CODESYS Forge talk (Post)}
After correspondence with Mr Schwellinger from Codesys the resolution for this was to uninstall the SL 4.14 and install SL 4.13 on the device. Once this was done the licensing worked as expected. I noted that the container then showed a Version 3.00 and not 0.00.
Last updated: 2025-01-11

Post by oscardm on Problem install codesys 3.5.17 SP 30 with Codesys Installer ^{CODESYS Forge talk (Post)}
Hi, I have a problem with codesys installer: if install a package on the codesys 3.5.17 SP17, and i try to install a package, for example SVN package, the codesys installer report the "digital signature expired error". Anyone have an idea for resolution ? Thanks for your feedback
Last updated: 2024-01-12

Post by schelchpaul on Problem with missing content in Dialog Windows in Win11 ^{CODESYS Forge talk (Post)}
Hello, i have the big Problem that dialog windows in Codesys 2.3 are cut off, as seen in the attached screenshots. I've tried to adjust the screen resolution, i tried changing scaling, i tried the compatibility options. To keep it short, nothing worked. If someone already had that problem and knows a fix, please answer.![]
Last updated: 2026-01-14

Post by schweizer on Position und Größe optimal anpassen (Container.Height - Visu.Height) funktioniert nicht. ^{CODESYS Forge talk (Post)}
Hello forum Does anyone have experience with optimally adjusting the position and size of the visualization elements? For us, the adjustment on the x-axis works in Codesys 3.5 SP20 with (Container.Width - Visu.Width). However, the y-axis is not affected with (Container.Height - Visu.Height). We implemented this according to the example from Codesys "Optimally adjust position and size" and had no success. Thank you very much for your help.
Last updated: 2024-07-29

Post by trusty-squire on implementing continuous movement in Codesys ^{CODESYS Forge talk (Post)}
What do you mean by continuous movement? You want to continuously follow a dynamic target position? SMC_ControlAxisByPos, which is typically used with CNC Interpolators, could work for that. Instead of feeding the target position in from the Interpolator, feed in the target position from your server instead. Once you enable the FB, it will continuously move the axis to track the fSetPosition input. https://content.helpme-codesys.com/en/libs/SM3_CNC/Current/SM_CNC_POUs/SoftMotion-CNC/Direct-Axis-Control/SMC_ControlAxisByPos.html
Last updated: 2024-09-12

Sort by relevance or date