Post by xabier on No work Control Torque Codesys with Drivers M751 Control Techniques ^{CODESYS Forge talk (Post)}
YEs..This drive supported Softmotion... I attaced the photos...for example with this driver can i move in absolute mode but i can´t aplicated FB set Torque and the 2 FB are down the same libre SM3_Basic
Last updated: 2024-03-14

Post by xabier on No work Control Torque Codesys with Drivers M751 Control Techniques ^{CODESYS Forge talk (Post)}
Please...can you help me???I don´t understand...Where check it that you tell me ??Where appear Pdf??? I need more support thanks
Last updated: 2024-03-14

Post by paro on Modbus Client Request Not Processed ^{CODESYS Forge talk (Post)}
Hi, Problem in your code is that you are not calling the ClientFb cyclic. Please look at the Example from CODESYS: https://forge.codesys.com/prj/codesys-example/modbus/home/Home/ Your code works if the client fb is called cyclic! IF NOT initDone THEN initDone := TRUE; // configure clientTcp clientTcp(aIPaddr:=Ethernet.IPAddress, uiPort:=502); // configure clientSerial clientSerial(iPort:=SysCom.SYS_COMPORT2, dwBaudRate:=SysCom.SYS_BR_115200, byDataBits:=8, eParity:=SysCom.SYS_EVENPARITY, eStopBits:=SysCom.SYS_ONESTOPBIT, eRtuAscii:=ModbusFB.RtuAscii.RTU); // configure clientRequestReadCoils_1 clientRequestReadCoils_1(rClient:=clientTcp, uiUnitId:=42, udiTimeout:=TO_UDINT(T#10MS)); // configure clientRequestWriteSingleRegister clientRequestWriteSingleRegister(rClient:=clientTcp, uiUnitId:=43, udiTimeout:=TO_UDINT(T#10MS)); // configure clientRequestReadCoils_2 clientRequestReadCoils_2(rClient:=clientTcp, uiUnitId:=44, udiTimeout:=TO_UDINT(T#10MS)); // configure clientRequestReadInputRegisters clientRequestReadInputRegisters(rClient:=clientTcp, uiUnitId:=44, udiTimeout:=TO_UDINT(T#10MS)); END_IF // call the client FB's clientTcp(); clientSerial(); // call client request FB's clientRequestReadCoils_1(rClient:=clientTcp, xExecute:=TRUE, uiStartItem:=2, uiQuantity:=3, pData:=ADR(aDataCoils_1[0])); // for more details see Example_TCP, especially ClientRequest control (xExecute, xDone, xError). IF clientRequestReadCoils_1.xDone THEN // get data from aDataCoils_1 ... END_IF clientRequestWriteSingleRegister(rClient:=clientTcp, xExecute:=TRUE, uiItem:=3, uiValue:=123); clientRequestReadCoils_2(rClient:=clientTcp, xExecute:=TRUE, uiStartItem:=2, uiQuantity:=3, pData:=ADR(aDataCoils_2[0])); clientRequestReadInputRegisters(rClient:=clientTcp, xExecute:=TRUE, uiStartItem:=16, uiQuantity:=3, pData:=ADR(aDataInputRegisters[0]));
Last updated: 2024-05-29

Post by eld-t on Change Git local repository folder name ^{CODESYS Forge talk (Post)}
Hi, how do you change the Git local repository folder name? It is called "project" by default, so we would like to rename it to something more descriptive especially for the remote repo's sake. Thanks!
Last updated: 24 minutes ago

Post by amy123 on codesys mqtt publish serialization ^{CODESYS Forge talk (Post)}
Hello, I am using the CODESYS IIoT Libraries SL MQTT Publish. Does this publish block only support publishing STRINGS as a readable format? I can publish ENUM, STRUCT, BOOL; however, MQTT Explorer will only display strings. When I use Wireshark, I can see that it is publishing something, but it looks to be publishing a serialized version which is a bunch of 0s or random text. If so, is there any way to deserialize this information back into a readable format? See pictures, where I have a BOOL TRUE that gets published as 001. Then see where I publish a STRUCT and it's an incomprehensible combination of 0s - only the string variable is displayed. Or, is it expected that you convert everything to a string before publishing? Any help is greatly appreciated! :)
Last updated: 2024-02-16

Post by dom4u on Using PEAK CAN PCIe card (IPEH-004040) with Codesys Control RTE V3 ^{CODESYS Forge talk (Post)}
The problem is that newer PeakCAN cards are with CAN FD support and SJA1000 compatibility isnt mentioned anymore on website. anyway, is it possibile to add a seperate entry for it in: [CmpSJACanDrv] ? Edwin, can you give us a hint how to format it?
Last updated: 2024-12-16

Post by suyash on Version Control ^{CODESYS Forge talk (Post)}
Hello, I face issues opening old Codesys 3 program when I am having a newer version installed. Unfortunately since I was forced to format my laptop after an unexpected crash. I lost all the setup files of the older versions. Is there ant where I can download it from? BR, Suyash
Last updated: 2025-03-07

Post by kevin123 on MessageKey for missing library dialog ^{CODESYS Forge talk (Post)}
Hi Martin, I got the messagekey of the "upgrade format warning dialog" with key:"<< No Key>>". (please refer to the attachment) Is that means i can't use system.prompt_answers["<<No Key>>"] = PromptResult.OK; to auto-answer 'OK' in this dialog? Is there any other way to auto-answer this dialog? Thanks!
Last updated: 2024-01-26

Post by rmaas on Fieldbus has lost synchronicity ^{CODESYS Forge talk (Post)}
Hi, On a gantry system with 2 axis i am getting the following error: SMC_DI_FIELDBUS_LOST_SYNCRONICITY This happens random, sometimes it happens every 5 minutes and sometimes no error for 2 hours... The Setup: - Using codesys 3.5 SP20 with all latest libs... - Kontron AL Pi-Tron CM4 with Preempt realtime patch (Raspberry Pi 4) - Codesys runtime 4.11.0.0 (single core) - CODESYS Control for Raspberry Pi SL licensed - Softmotion + CNC + Robotics licensed - 2x Leadshine EL8-EC400 servo drives - Axis group for a 2-axis T-Gantry Ethercat network wiring: Ethercat master softmotion -> Beckhoff EK1100 -> Servo drive #1 -> Servo drive #2 Ethercat Cycle time = 4ms Max Jitter = 140~150 What i have tried so far: - changed the sync offset from 20% to 30% - changed ethercat task priority from 1 to 0 Running tasks: - Ethercat tast: Prio = 0, Interval = 4ms - Main task: Prio = 1, Interval = 8ms - Visu task: Prio = 31, Interval = 100ms - Softmotion planning task: Prio = 15, Freewheeling - 3 other default tasks that were created by AC_Persist Motion fb's are called in the ethercat task... Does anyone have an idea how to fix this? Any help is greatly appreciated!
Last updated: 2024-04-11

Post by davidbo on RPI can system operation like rm in a shell have an impact on a Task cycle time ^{CODESYS Forge talk (Post)}
I have noticed that a rm file1.txt command on a shell has an impact on the cycle time for a TASK writing to file2.txt. Seen in the Monitor fane of the Task configuration Furthermore if a TASK makes a system call like rm, its cycle time increases of course but it seems to have an invisible impact on other TASKs too. I have a TASK for handling communication over the CANbus (SPI) where it stops sending "Heartbeats" for many seconds when another TASK does a system rm. Why is that not seen on the Monitor fane? Is even codesyscontrol paused when system calls are made? The CPU load is about 30-40%
Last updated: 2024-09-23

Post by pernockham on Slider instance value when accessed through "execute ST-code" ^{CODESYS Forge talk (Post)}
I have a time which I want to modify with a slider. I have confirmed it is possible to set the value of the slider by to_real(time) (I can see that the slider changes according to 'my_time_value's value). Slider variable: to_real(my_time_value); However I fail to access the current slider instance value when I want to write back the value as time (write to a variable will not work as I need a type-conversion before assignment). my_time_value := to_time(slider-instance-value); I tried with this^.? but could not see anything interesting and also THIS^.GEN_Instance.? but nothing resemble what could be the sliders value. Anyone that knows? Thanks!
Last updated: 2025-02-06

Post by alexgooi on Codesys virtual control redundancy ^{CODESYS Forge talk (Post)}
Dear Forum, I’m currently investigating the possibilities of Codesys virtual control (Linux). The research rig consists of a PC (Debian with real time kernel) with a docker server installed on it. The PC is communicating with a Remote I/O and I have to say the performance is great. The process in the container is running (soft) real time. Currently I’m checking if it is possible to replace physical controllers by remote I/O’s and run the Codesys applications on a docker server. If I’m going into this route the reliability of the server is very important (server down, complete installation down), is it possible to make the server redundant without needing 2 separate containers (including licenses), and maintaining the real time behavior? I’m not only expecting direct answers, if you have any idea or thought they are very welcome. Kind regards Alex
Last updated: 2025-09-03

Post by dhumphries on Ethernet/IP Issue ^{CODESYS Forge talk (Post)}
Make sure the O->T and T->O bytes required by the remote device match the configuration in Codesys. Most of the EDS files I've imported have not worked by default. See the attached images for the connections and assemblies tabs. Note that the connections are in Bytes and the assemblies are in bits, you have to have enough bits to equal the bytes. Either mismatch will give a red/orange triangle. Page 343 of the manual (assuming the STF10-IP is an applied motion microstep driver) has some recommended connection settings, you should be able to confirm the input and output bits somehow, some devices have a web GUI, some require a software tool.
Last updated: 2024-02-03

Post by dhumphries on Not able to see input data coming from eip adapter on codesys ^{CODESYS Forge talk (Post)}
Does the device have a green icon next to it when the PLC is running? If not you have some kind of communication problem, wireshark may be picking up some data but the scanner may not be configured correctly to receive the data. Check the T>O and O>T bytes and make sure they match on both the scanner and adapter. I've had very little success loading a .eds file and having the configuration work without some manual configuration. If you have a green icon, have you enabled the device to always update variables?
Last updated: 2024-03-02

Post by timvh on IECStringUtils.FormatDateTime ^{CODESYS Forge talk (Post)}
There has been a fix in SP21. I tried it in this version with the option "Use unicodestring" enabled in the Visualization Manager and it worked if the variables used for the function are declared as WSTRING variables wsFormat : WSTRING := "%t[HH:mm:ss dd.MM.yyyy]"; wsTime : WSTRING; IECStringUtils.FormatDateTime(cbpResult := ADR(wsTime), uiResultCapacity := SIZEOF(wsTime), cbpFormat := ADR(wsFormat));
Last updated: 2025-07-29

Post by rikher on Error: Too few outputs exixts for the box 'MemCopy' (minimum is 1). ^{CODESYS Forge talk (Post)}
I am using MemCopy Function for this example: https://www.youtube.com/watch?v=DeTCT5Vyn28&t=482s It is from library WagoSysPlainMem. I want to use this for an MQTT example. However, Codesys is complaining the block does not have outputs. How to fix this?
Last updated: 2024-06-19

Post by xabier on License Activation Problems ^{CODESYS Forge talk (Post)}
I bought two license and install with out problems....but the problem was when i changed the image in my controler and when i want activated again the license i have a problem Appear this 2 softcontainer and i can´t install any license again... Can someone help me please?
Last updated: 2024-06-24

Post by dkugler on TargetVisu Freezing ^{CODESYS Forge talk (Post)}
The only weird situation i remeber with particular or complete frozen target visu was after the rtc clock was fallen or set back to the past. It looked like after running a while the alarm history database crashed during writing entries at a date lot of years in the past. After setting the rtc clock to actual date/time and deleting the alarm db every thing worked fine. I don't know, if this is/was a problem of our PLC hardware/firmware? Maybe check date/time at your system?
Last updated: 2024-09-13

Post by davidbo on RPI can system operation like rm in a shell have an impact on a Task cycle time ^{CODESYS Forge talk (Post)}
CODESYS Control for Raspberry Pi MC SL v4.4.0.0 CANopen_Manager 4.2.0.0 I did not call rm directly from my TASK-i2c, it was trough the attached python script. It is not always a problem happens, but sometimes a rm takes a long time. I reduced the amount of calls to logi2c.py but I don't understand why TASK-i2c sometimes can cause problems for TASK-CAN
Last updated: 2024-09-27

Post by davidbo on RPI can system operation like rm in a shell have an impact on a Task cycle time ^{CODESYS Forge talk (Post)}
CODESYS Control for Raspberry Pi MC SL v4.4.0.0 CANopen_Manager 4.2.0.0 I did not call rm directly from my TASK-i2c, it was trough the attached python script. It is not always a problem happens, but sometimes a rm takes a long time. I reduced the amount of calls to logi2c.py but I don't understand why TASK-i2c sometimes can cause problems for TASK-CAN
Last updated: 2024-09-27

Post by ph0010421 on Task time too fast? ^{CODESYS Forge talk (Post)}
Hello I've made an FB which is a TCP server. It uses the excellent CAA NetServices library. If I have the FB in a task <4ms, then the RT crashes immediately at boot up. If the task >=4ms, it starts and runs perfectly. This is even if the block is not doing anything; just instantiated. Am I missing something silly? Why would a low task time cause this? 4ms is perfectly adequate, but I'm just interested why... thanks PH
Last updated: 2024-11-27

Post by trusty-squire on AXIS Rollover ^{CODESYS Forge talk (Post)}
In that case, the best thing to do might be to track the offset in a separate variable of your logic, then when you provide target positions, make your target position use the tracked offset as below: ActualTargetPosition := (TargetPosition + MyOffset) MOD 360; Although, upon further reflection, you'll still have the same cycle time issues. You might be able to break your code into multiple tasks to reduce the cycle time, or use an Event task to capture the offset position?
Last updated: 2025-03-12

Post by tvm on multiply gives negatives ^{CODESYS Forge talk (Post)}
It's probably because you have an INT in the input to the MUL function, which will then try to output an INT as well. INT variables can only handle values of -32768 to 32767. Your value of 523000 won't fit in an INT, so it turns into an invalid number. Use a DINT. This is usually better for working with time values anyway, because time values are all 32 bit. Or if you can't, use INT_TO_DINT(gvlp.detectie_nalooptijd_s) in the input to the MUL function.
Last updated: 2024-01-04

Post by micik on CAA File, how to check whether file exists or not ^{CODESYS Forge talk (Post)}
Hello, what would be the most efficient way to check whether the file exists or not. I don't want to use file.Open function, it seems like rather inefficiet operaton. I considered GetAttribute function, but this function doesn't accept filename (with path) as an input. Basically I need to check first time when program is loaded to the runtime i.e. when application is started for the first time, whether a file exists on the specific location or not.
Last updated: 2024-05-16

Post by msirotkin on EtherCAT status errors ^{CODESYS Forge talk (Post)}
Didn't help. I'm just trying to understand why the errors occur. Are they from the poor driver or from the Linux network stack. That's why I wanted to know how the rxerros and lostframes are counted. Because in other places (like ethtool info) there are no any issues. And the Ethercat device works fine. And it also strange that on the second ethernet port with a different HW and driver Ethercat works better, but still time to time gets such errors.
Last updated: 2025-11-26

Sort by relevance or date