Post by marcolim on Slow modbus digital input response ^{CODESYS Forge talk (Post)}
[Update]. My issue's solved, I applied the resistors in Pull-down configuration on each digital input. In thus configuration never happened "floating or delaying" acquisition on SoftPLC/Arduino Board.
Last updated: 2024-04-15

Post by eschwellinger on Can't use new licensing with Raspberry Pi ^{CODESYS Forge talk (Post)}
please delete the contents of the following directory - /var/opt/codesys/.cmact_license/ then start a new SPS and then the activation should work (then you have a new empty UFC SoftContainer)
Last updated: 2024-04-22

Post by yannick on Raspberry PI 5 not working ^{CODESYS Forge talk (Post)}
Thanks for your quick help. It's working until I do a reboot of the raspberry PI. After that it goes back to 2024-04-20. How's that possible?
Last updated: 2024-04-29

Post by radekkoza on How to use GPIO (and IOT2000 IO-Module) with CODESYS Control for IOT2000 SL ? ^{CODESYS Forge talk (Post)}
Hi I have this question I can't find anywhere what pins Di3 and Di4 have all the rest work . I have a 10 input iot2000 card
Last updated: 2024-05-05

Post by radekkoza on How to use GPIO (and IOT2000 IO-Module) with CODESYS Control for IOT2000 SL ? ^{CODESYS Forge talk (Post)}
Hi I have this question I can't find anywhere what pins Di3 and Di4 have all the rest work . I have a 10 input iot2000 card
Last updated: 2024-05-05

Post by radekkoza on How to use GPIO (and IOT2000 IO-Module) with CODESYS Control for IOT2000 SL ? ^{CODESYS Forge talk (Post)}
Hi I have this question I can't find anywhere what pins Di3 and Di4 have all the rest work . I have a 10 input iot2000 card
Last updated: 2024-05-05

Post by eschwellinger on Ethercat bus on Beckhoff CX with Codesys for Linux ^{CODESYS Forge talk (Post)}
yes I think you need to build the kernel drivers for the CCAT driver for the backplane ETC networkcard https://github.com/Beckhoff/CCAT/
Last updated: 2024-05-13

Post by rafaelbrito on Licensing info not available. ^{CODESYS Forge talk (Post)}
Hello, I'm having the same problem. I'm trying to license Codesys running in a Linux container, which I downloaded from the following link (https://hub.docker.com/r/hilschernetiotedge/codesys_control_sl_linux). The same error that you mentioned appears. Is there any solution?
Last updated: 2024-05-22

Post by totorovic on IO-LINK Package - new license model ^{CODESYS Forge talk (Post)}
Thank you for your answer. Finally I don't confirm that it used to work before. It seems that the IO-link Package is needed is you want to configure the network, but you don't need it if you use generic IO-link devices.
Last updated: 2024-06-06

Post by eschwellinger on Licensing info not available (WAGO PFC200 + Codesys V3) ^{CODESYS Forge talk (Post)}
Seems that the Wago Target does not support the licensing. Either use PFC200 SL from CODESYS Store or ask the Wago support for help.
Last updated: 2024-06-10

Post by paulg on CODESYSControl_User.cfg - link to documentation? ^{CODESYS Forge talk (Post)}
Is there somewhere in the Codesys help files that generally details what configuration options are available for this file, and what details it logs regarding the configuration file? Or is that going to differ by libraries being used? Thanks!
Last updated: 2024-06-11

Post by fajean on CODESYS control on RPi starts, shortly runs, then exits ^{CODESYS Forge talk (Post)}
https://us.store.codesys.com/codesys-control-for-raspberry-pi-sl.html Quoted from the "additional requirements" section : The operating system Raspberry Pi OS (32-bit)
Last updated: 2024-06-14

Post by kthomas on Cant login to Rpi4 but can see it in codesys communications settings. ^{CODESYS Forge talk (Post)}
This is what I see in codesys window. And here is with the netstat command on the pi
Last updated: 2024-06-23

Post by eschwellinger on Two OneWireMaster on one Raspberry PI 5 ^{CODESYS Forge talk (Post)}
you need to have an own task for the one wire and io update these slaves in an own low prio task!
Last updated: 2025-10-18

Post by s1mon on Two OneWireMaster on one Raspberry PI 5 ^{CODESYS Forge talk (Post)}
yes sure. Thx for your support! This is the Codesys project stripped down only to my EtherCat and OneWire Configuration. The Project now contains only one OneWire Master on GPIO4.
Last updated: 2025-10-20

Post by eschwellinger on Two OneWireMaster on one Raspberry PI 5 ^{CODESYS Forge talk (Post)}
the project has only one OneWire Master - so if you add the setting "PlaceholderFilePath.2=/sys/devices/w1_bus_master2, $OneWire2$ to the config file it will fail and the Ethercat task will be blocked by the OneWire Master readings?
Last updated: 2025-10-21

Post by eschwellinger on Two OneWireMaster on one Raspberry PI 5 ^{CODESYS Forge talk (Post)}
Could you check the taskcycle time in the taskmonitor (online monitor) - do you really see this 1s on Ethercat Task? Need to check this on my hardware but will take some time...
Last updated: 2025-10-21

Post by ahmed-abohelal on SysComRead Timeout Parameter ^{CODESYS Forge talk (Post)}
Hello I was facing the same problem i have to increase the timeout since the unit looks like to be in us SysComread(hCom:=hCom,pbyBuffer := ADR(readBuffer[0]),ulSize:=128,ulTimeout:=3000000,pResult:= ADR(readRes));
Last updated: 2025-10-22

Post by kalmeyer on Stepper motor control with (SM_Drive_RaspStepper_direct) ^{CODESYS Forge talk (Post)}
I have installed: SM_Drive_PosControl 4.18.0.0 and SM_Drive_RaspiStepper_Direct 0.0.0.7 and SM_Drive_RaspiStepper_PulsDir 0.0.0.7 And when I "Generate Code" I immediately get 6 errors (see attached file) What can I do?????
Last updated: 2025-11-09

Post by kalmeyer on Stepper motor control with (SM_Drive_RaspStepper_direct) ^{CODESYS Forge talk (Post)}
Is there perhaps a place where I can see examples of programming with different instructions? This would be a great help. Maybe there are some places where ready-made programs are posted that can be downloaded and tested? /Klaus
Last updated: 2025-11-10

Post by eschwellinger on Stepper motor control with (SM_Drive_RaspStepper_direct) ^{CODESYS Forge talk (Post)}
.. try to use this projectarchive for the Stepper. In case you search for SoftMotion Examples: "c:\Program Files\CODESYS 3.5.21.X\CODESYS\CODESYS SoftMotion\Examples\Tutorial\"
Last updated: 2025-11-11

Post by jonasz on Deploy LicenseServer for Linux SL ^{CODESYS Forge talk (Post)}
After carefully studying the documentation, I have a question: is a second hardware-independent time source required for the correct operation of the VirtualSafety system?
Last updated: 2025-11-17

Post by jonasz on Deploy LicenseServer for Linux SL ^{CODESYS Forge talk (Post)}
Thank you for your response. Is there documentation for the commands? I spent a lot of time trying to figure this out. I have a potato computer at home, so I'll have to test this later.
Last updated: 2025-11-21

Post by davidbo on License problem with Raspberry Pi ^{CODESYS Forge talk (Post)}
To simplify your problem you shall not select dongle and get dongle errors. Do as shown In some cases you need 2 different licenses depending on the metrics. And yes the system gives not always give proper error messages when you try to reinstall a license
Last updated: 2025-12-01

Post by timvh on Modbus TCP Server connection is ESTABLISHED but all holding registers are value 0? ^{CODESYS Forge talk (Post)}
Are you sure you need to read holding registers? Have you tried reading input registers?
Last updated: 2026-01-07

Sort by relevance or date