Post by gseidel on CAM Motion Recover after STO ^{CODESYS Forge talk (Post)}
Dear Mr. Kolev, I'm not sure I understood correctly. But this is my take on your question: When the STO of the slave is triggered, store the current master position (e.g. 225 units) After the reset of the slave error, call MC_SetPosition on the virtual master and reset it to the stored position (225 units) Optionally, before MC_CamIn is restartet, move the slave back to the slave position corresponding to the stored master position. (If you do this, no ramping in will be necessary) Restart MC_CamIn, with absolute master position and absolute slave position. Choose the StartMode that is appropriate for your machine. Best regards, Georg Seidel
Last updated: 2026-02-16

Post by hannibal on Codesys Trend - setting Y axis minimum and maximum as variables - error ^{CODESYS Forge talk (Post)}
I am experiencing an issue when trying to define the Y-axis limits in a Trend Graphic using variables. When I set the Minimum and Maximum values as variables, an error is triggered. My goal is to make the Y-axis limits dynamic so they can adjust according to the installation. Both variables are initialized as follows: gP_YMin = -100.0 gP_YMax = 100.0 However, I still get the following error: "The minimum axis value must be less than the maximum axis value" Does anyone have an idea why this is happening or how to resolve it?
Last updated: 2026-03-22

Post by hannibal on Codesys Trend - setting Y axis minimum and maximum as variables - error ^{CODESYS Forge talk (Post)}
I am experiencing an issue when trying to define the Y-axis limits in a Trend Graphic using variables. When I set the Minimum and Maximum values as variables, an error is triggered. My goal is to make the Y-axis limits dynamic so they can adjust according to the installation. Both variables are initialized as follows: gP_YMin = -100.0 gP_YMax = 100.0 However, I still get the following error: "The minimum axis value must be less than the maximum axis value" Does anyone have an idea why this is happening or how to resolve it?
Last updated: 2026-03-22

Post by poliautomacao on Absolute movement controlled by an external encoder. ^{CODESYS Forge talk (Post)}
Hello, I made this configuration, I'm moving the encoder value to SM_Driver_PosControl.in.wActPosition. When I make the absolute movement of my PosControl axis, my physical drive axis rotates perfectly, but I noticed that the movement is not followed by the encoder. That is, if I hold the encoder and keep it in position 0, the PosControl axis makes the absolute movement of 314 mm and stops, which is strange because the encoder is at 0. Theoretically, the PosControl axis should accelerate to try to compensate for the movement error. I haven't yet achieved perfect functionality.
Last updated: 2026-03-24

Post by husarz17 on How change Unity-ID in TCP Modbus Slave ^{CODESYS Forge talk (Post)}
My codesys is 3.5.21.30. I am using function ModbusServer from library ModbusTCP_Slave. The reason is that I need share 9000 Holding registers. By standard configuration it is only 4096. fbMbTcpDevice: ModbusTCP_Slave.ModbusServer; fbMbTcpDevice( wPort := 502, pInputData := ADR(awInputReg), pOutputData := ADR(awHoldingReg), uiInputDataSize := 10, uiOutputDataSize := 9000, xEnable := TRUE, tTimeout := 10000, InterfaceName := "eth0", xBusy => xBusy, xError => xError, byClientConnections => byConnections ); Ethernet port is cofigured: Network interface: eth0 IP address: 10.10.22.55 Subnet maskL 255.255.255.0 Default gateway: 0.0.0.0 And it only works when I am reading registers with ID 255 by Modbus Poll. Any other IDs don't work. The actual TCP client device try to read registers with ID 1 and I can't change it... Thanks in advance for your help!
Last updated: 2026-04-01

Post by cvrettacos-dse on How to reset scroll of a table element ^{CODESYS Forge talk (Post)}
Hello, I would like to use swipe/pan gestures to scroll a table visualization element (CODESYS 3.5.21.10) ona DSE M810 display. The swipe / pan gesture control works fine, however, I cannot figure out how to reset / navigate to the top of the table again with code. I have tried the Scrolling begin variable, and the visu manager is setting it to FALSE right away but the table doesn't actually scroll back to top. If I check the “Scroll elements with scrollbar” box, then the Scrolling begin variable works perfectly, but now the swipe/pan scrolling no longer works and you have to use the scrollbar. Any assitence you can provide is appreciated. Thanks.
Last updated: 2026-04-21

Post by timvh on Codesys v3.5.22.10 - Fail to create a project Archive ^{CODESYS Forge talk (Post)}
There is an issue with adding the visu styles to the archive with Visu add-on 4.9.0.0 and 4.9.1.0. When you create the projectarchive disable the option to add the style(s) to the archive. CODESYS support informed me it will be fixed with visu add-on 4.10.0.0 (May 26th 2026). An alternative is to start CODESYS as Administrator. Then it will work with styles as well. You could start CODESYS as Administrator by first opening the CODESYS Installer. At the bottom you can select to start the Installer as Administrator. If you do this and then start the CODESYS version from this installer, it will work.
Last updated: 2026-04-25

Post by timvh on library inside library ^{CODESYS Forge talk (Post)}
1) it should be possible to access the type SysTime in the project as A_Lib.SysTime. 2) you could add the SysTimeCore library to the library manager of your library (POU Pool). This might seem as a double library, but because of the placeholder resolution only one will be used. Then, in your library manager of your library, select the SysTimeCore library, right-click, select "Properties" and enable the option "Publish all IEC symbols ...." For more information about library development, you could follow our advanced training course in Ridderkerk. The next is scheduled for 24 and 25 June 2026 https://www.extendsmartcoding.nl/codesys-training/
Last updated: 2026-04-25

Post by brouwyka on JSON Utilities - JSON file written with invalid structure ^{CODESYS Forge talk (Post)}
Hey there! I am currently running into the exact same issue (and have also posted to a similar post here: https://forge.codesys.com/forge/talk/Engineering/thread/c45929e2f1/#e27f). The JsonData object has all inexes & parent indexes in the way I expect, everything is correctly "linked". It purely seems that the writer is incorrectly parsing said JsonData, not based on parent & child index, but on something else that breaks it and puts things at the root, instead of the specified parent index. Did you ever manage to find a solution, or another way of achieving your JSON composing? I'm currently working on Codesys V3.5 SP19 Patch 7 with IIOT Libraries SL 1.13.0.0, specifically JSON Utilities SL 1.13.0.0 (to send requests to APIs with JSON bodies using Web Client SL 1.13.0.0).
Last updated: 2026-06-08

Post by ophelia on Phantom Test Slot Preventing Suite Completion ^{CODESYS Forge talk (Post)}
Hi all, I'm working with a CODESYS 3.5 unit test framework on an embedded Linux PLC and running into an issue where a phantom test slot appears in the results that never completes, preventing the full test suite from ever finishing. The symptom: A blank-named test entry appears in the results table with an ever-increasing action count. It stays as "Testing" or "Failing" indefinitely. Because it never closes, bAllFinished never goes TRUE and the final report is never generated. Question: Has anyone seen this kind of phantom slot issue in a CODESYS unit testing setup? Thanks
Last updated: 2026-07-09

Post by williamcorlin on The future and proper use of CAA.BOLT, CAA.SEMA,.. ^{CODESYS Forge talk (Post)}
I've been moving in the same direction. For new libraries, I'm trying to minimize dependencies on APIs that look like they're being phased out unless the documentation explicitly recommends them. For synchronization primitives like CAA.BOLT and CAA.SEMA, I'd love to see an official replacement or abstraction layer that's guaranteed to remain stable across runtimes. That would make library development much cleaner than relying on platform-specific SysLib* implementations or conditional compilation everywhere. Until there's clearer guidance, my approach has been to isolate the locking mechanism behind a small wrapper interface. If CODESYS changes the recommended API in the future, only that wrapper needs to be updated instead of every library that uses it. It isn't perfect, but it's made maintenance much easier. https://forge.codesys.com/forge/talk/Engineering/thread/e6c20a740e/ https://zapgames.io/
Last updated: 2026-07-14

Post by timvh on HTML5 visualization controls disabled on CODESYS Control for Linux SL - overlay not supported? ^{CODESYS Forge talk (Post)}
I was able to reproduce this by doing something wrong. I guess what you did is first create an application for the Control Win, or some other device and then switched this to the Linux SL. But then the Visualization Manager still has the "TargetVisu" component, besides the WebVisu component. The Linux SL doesn't support this TargetVisu as part of the runtime. You should run a separate process for this. So remove the TargetVisu from the Visualization Manager and then you will be able to load the application.
Last updated: 2026-08-06

Post by fless on No source code available for profinet library ^{CODESYS Forge talk (Post)}
looks like you are running in a bug in the newest version 4.4.0 of the profinet library or the new library triggers a bug in your code. did you update your profinet device too? you could try to downgrade to an older version of the library. via library manager - placeholders, double click Profinet 4.4.0 in the library column and choose an older version.
Last updated: 2023-08-23

Post by ryandmg on Web Client (HMI) Disconnects from Webvisu (Weidmuller u-OS) ^{CODESYS Forge talk (Post)}
Ohhh OK. Yeah this seems to be timing like you said. Yeah I read through that document and came to the same conclusion. I haven't tried setting them both to 200ms. Maybe I'll give it a shot. Thanks so much for your input. Its greatly apreciated.
Last updated: 2023-09-06

Post by martinlithlith on Device User Logon and No device is responding.. Pi4b codesys 3.5 SP19 2 + (64-bit) ^{CODESYS Forge talk (Post)}
Hi, Thank you for your reply! What should be the version 4.9.0.0? I have a user named pi on the pi, thats what i´m using as credientials to be able to for example update/install runtime. Or do i need another user? once agin, thank for the reply! Martin
Last updated: 2023-09-11

Post by transmin01 on EL6751 Canopen_Manager issue ^{CODESYS Forge talk (Post)}
Hi, I have a Beckhoff EL6751 EtherCAT / CANopen gateway which fails on the Canbus when the CANopen_Manager is added. Currently no devices are connected to the EL6751. If I add a device, I get the same issue. If I add a device and connect the bus, I get the same issue. Is there something I am doing wrong? Regards Trevor
Last updated: 2023-09-12

Post by spareparts on SPI Master not running/MCP3008 Missing driver. ^{CODESYS Forge talk (Post)}
I believe I have installed the correct device descriptions and library, in an attempt to use the MCP3008 in conjunction with RPI; when project runs the MCP3008 is unable to find the correct driver. Is there anything I'm missing? Very new to this so any help is apprecated!
Last updated: 2023-09-12

Post by transmin01 on EtherCat Master cannot open network adaptor on Win10x64 target ^{CODESYS Forge talk (Post)}
Hi, If I utilise an EtherCat master with a Beckhoff EK1100 coupler on a Win10x64 target I get a "Network Adaptor could not be opened" error. I have tried this on both a VM and a physical PC. Has anyone experienced this issue? Regards Trevor
Last updated: 2023-09-14

Post by snhatton on Alarm Management - latched variable represented as Text list ^{CODESYS Forge talk (Post)}
Hi There, For my understanding: are you trying to display the contents of a text list in an alarm message based on the id? For example, you could maintain a text list of common alarm messages, and then display based on which message is true?
Last updated: 2023-09-18

Post by lucaver89 on Raspberry pi 3 and runtime 4.9.0.0 ^{CODESYS Forge talk (Post)}
Good morning, I'm using a raspberry pi3 as plc with the runtime 4.9.0.0. My program has many of retrain variables but when an update is performed the retrain variables comes back to default values. Is the a way to backups the retrain variables n a csv file? Is still the way to restore them from the csv? Thank you for helping Luca
Last updated: 2023-09-23

Post by derpaul on Official MQTT-Client: MAX_RECEIVE_BUFFER_SIZE_EXCEEDED ^{CODESYS Forge talk (Post)}
I've post the Versions in the Attachments. It seems with htop, that there is a very high CPU Load. In the Log I can see nothing, as mentioned above I've to restart the PLC with Power off/on and the log in codesys was deleted. Or what do you mean with plclogger?
Last updated: 2023-09-23

Post by sivakov on CoDeSys Exception EIP Adapter ^{CODESYS Forge talk (Post)}
Hi, Got same problem, appeared after 4.3.1.0 update. Prabably problem is in performance. I am using virtual machine, so adding one more core and several GB to RAM still not solved, but atleast did system more stable. Try optimise your main program or set less task interval. Regards, I will be your mate in solving this mistery =)
Last updated: 2023-09-28

Post by ltrinta on AWS IoT Core connection using AWS certificates ^{CODESYS Forge talk (Post)}
Hi there I want to know if there is possibility to connect a CODESYS application to AWS IoT Core using the certificates owneds by AWS. In the examples of CODESYS using AWS IoT Core library, we need to generate a local certificate and update it to AWS IoT Core. I want to use AWS IoT Core certificates. Regards, Leonardo
Last updated: 2023-09-28

Post by dgrard on Camera RTSP Feed ^{CODESYS Forge talk (Post)}
Hello Is it possible to view a camera RTSP feed in a visualization? It seems as though the browser element doesn't support this and we are trying to replicate an example using the ActivX element with no luck. We are using the Windows Control Win x64 device with a camera connected via LAN. If it is possible, can you provide some instructions please. Thank you
Last updated: 2023-10-17

Post by mawaloc on creationg on dynamic widgets ^{CODESYS Forge talk (Post)}
Hello, Is there is any way to create a different dynamic widget than what can be found on codesys. I would like to create similar with adding things like limits etcc. in codesys I just see 180 deg or 360 deg. and shape are differents Any tutorial on it. ThankYou
Last updated: 2023-10-20

Sort by relevance or date