Post by lostcontrol on Remote Ethernet/ip Adapter communication with scanner running on codesys ^{CODESYS Forge talk (Post)}
is the bus running.? what type of values/IO is the adaptor providing? do you have a map of the data layout? are you actually looking at the right offset?
Last updated: 2023-12-16

Post by lostcontrol on Bool turning on in case stament in wrong state? ^{CODESYS Forge talk (Post)}
i would be looking at what the case variable is doing then.. sounds like there might be a logic race going on
Last updated: 2023-12-16

Post by eschwellinger on Raspberry Pi ^{CODESYS Forge talk (Post)}
Which RaspberryPi OS - have you installed on the PI? At the moment, there is a problem with latest Bookworm from December. You need to downgrade to October version of the OS - or wait 4.11.0.0. is released ( February) https://downloads.raspberrypi.com/raspios_armhf/images/ 2023-10-10 16:13 Version will work.
Last updated: 2023-12-28

Post by reinier-geers on Time zone ^{CODESYS Forge talk (Post)}
I use a controller with Linux. I try to change timezone. but no result. The command of codesys i dont understand ?? And Linux Commands dont work. It stays at +0 . I want Amsterdam
Last updated: 2023-12-29

Post by ahessel on Raspberry Pi ^{CODESYS Forge talk (Post)}
Hello Mr. Schwellinger, why is there no release note at a central point with such incompatibilities? I also wasted a whole day until I found this thread by chance. best regards Andreas
Last updated: 2024-01-04

Post by jfd1981 on Ethernet/IP Issue ^{CODESYS Forge talk (Post)}
Hello all. I am trying to bring a stepper drive online, and it seems to be configured correctly, BUT I have the Orange triangle near it, and the diagnostic screen says "register session at the adapter"
Last updated: 2024-01-26

Post by matt-s on HMI Pushbutton/Move Instruction ^{CODESYS Forge talk (Post)}
I put the cross reference at the bottom of the pictures. It is not being written to elsewhere. I have tried the execute block too.
Last updated: 2024-01-26

Post by matt-s on HMI Pushbutton/Move Instruction ^{CODESYS Forge talk (Post)}
I put the cross reference at the bottom of the pictures. It is not being written to elsewhere. I have tried the execute block too.
Last updated: 2024-01-26

Post by ruben on DataSource not working ^{CODESYS Forge talk (Post)}
I had the same error. It took me a LONG way to figure it out, but in my case the problem was that I used LDATE_AND_TIME. It seems to be not supported, at least not in the Codesys version I used (3.5.16)
Last updated: 2024-02-01

Post by sturmghost on Visualization using methods and cyclic ST-calls ^{CODESYS Forge talk (Post)}
Not sure what you mean but you can define a visu initialization program and call it once at the visu initialization step. Look in the Visualization Manager there is a possibility to define such a program.
Last updated: 2024-03-03

Post by aniket-b on EtherCAT drive not moving ^{CODESYS Forge talk (Post)}
I have EtherCAT drive communicating properly without an error but when I use MC_JOG function, it is not moving at all, I can use MC_Power function and drive does respond to that but other functions are not working,. Please suggest what is wrong here.
Last updated: 2024-03-04

Post by schnepper on Error building Extension SDK Linux code ^{CODESYS Forge talk (Post)}
Solved: I started from a fresh project and everything worked. I had a Function Block in the project at one point and deleted it. I think Codesys doesn't fully clean up on deletes.
Last updated: 2024-04-02

Post by eschwellinger on Cannot install Codesys control Multicore in raspberry pi 4 ^{CODESYS Forge talk (Post)}
just add in /etc/CODESYSControl_Usr.cfg [CmpRasPi] Architecture=armv7l for the 32Bit MC version... this is what this dialog does (or at least should do)
Last updated: 2024-04-22

Post by gseidel on Warning C0564 when compiling CNC project with variables program ^{CODESYS Forge talk (Post)}
Hi Fless, thanks for your report! We created an issue in our bug tracker (SM-5109) and will have a look at this issue. Best regards, Georg
Last updated: 2024-04-30

Post by k2saki on CNC Override speed. SMC_Interpolator.dOverride is working ? ^{CODESYS Forge talk (Post)}
Hello. I have a question about override of moving speed. I am testing G-Code in Simulation mode. I set SMC_Interpolator.dOverride <--- 0.5, 1.0, 2.0 when Interpolator is working But SMC_Interpolator.dVel(speed) did not changed at all. Am I missing something to take effect ?
Last updated: 2024-05-01

Post by dkugler on RecipeManCommands.ReloadRecipes ^{CODESYS Forge talk (Post)}
Hi William, I struggled in the same way as you at the beginning with the recipe manager. This chapter helped me a lot to understand how it has to be used: https://content.helpme-codesys.com/en/CODESYS%20Recipes/_rec_start_page.html Check out the Methode LoadFromAndWriteRecipe / LoadAndWriteRecipe Good luck! Dave
Last updated: 2024-05-16

Post by kevinm on Data source and safety PLC ^{CODESYS Forge talk (Post)}
I am having the same trouble. However, if I change the Login Configuration settings to 'Type: Login using the credentials determined at runtime' then the Connection information continues as 'Connection state: Connecting' and 'Error information: OK'. There is no User Management on the source PLC.
Last updated: 2024-05-16

Post by dkugler on RecipeManCommands.ReloadRecipes ^{CODESYS Forge talk (Post)}
Hi William, I struggled in the same way as you at the beginning with the recipe manager. This chapter helped me a lot to understand how it has to be used: https://content.helpme-codesys.com/en/CODESYS%20Recipes/_rec_start_page.html Check out the Methode LoadFromAndWriteRecipe / LoadAndWriteRecipe Good luck! Dave
Last updated: 2024-05-16

Post by hwopereis on SFC Action problems ^{CODESYS Forge talk (Post)}
Only logged in to agree with the above. So counter intuitive. Why does an associated action force the variable when the step it is associated to is not active? Makes no sense at all, is terrible to debug and costs a lot of time. Such as shame.
Last updated: 2024-05-27

Post by jonasz on Deploy LicenseServer for Linux SL ^{CODESYS Forge talk (Post)}
Thank you for your response. Is there documentation for the commands? I spent a lot of time trying to figure this out. I have a potato computer at home, so I'll have to test this later.
Last updated: 2025-11-21

Post by dinesh-vamtec on RETAIN PERSISTENT only stored at gracefully shutdown? ^{CODESYS Forge talk (Post)}
I have an idea to save the persistent variable. Currently in testing processs. If testing completed I share the solution to you.
Last updated: 2025-11-26

Post by gseidel on STEPPER CODESYS SOFTMOTION_DRIVE ^{CODESYS Forge talk (Post)}
Hi kalmeyer, I would recommend to have a look at these examples. They come with a project and a description: https://content.helpme-codesys.com/en/CODESYS%20SoftMotion/_sm_basic_examples_single_axis.html. Best regards, Georg
Last updated: 2025-11-28

Post by kenth1973 on MC_Phasing state explenation ^{CODESYS Forge talk (Post)}
Hi George. Thx for the info and recommendation - the robot is running production at customer. But - would you have any information about the states numbers and their different explenations?
Last updated: 2025-12-11

Post by aniket-b on Scara3 kinematic robot error ^{CODESYS Forge talk (Post)}
I am using Scara3 kinematic with EtherCAT PLC. The robot stops at the same place randomly after few cycles. Check attached image. I am getting SMC_ERROR.SMC_DI_FIELDBUS_LOST_SYNCRONICITY in all 3 axes.
Last updated: 2025-12-19

Post by jeffgamsby on Accessing ModbusTCP addresses from python ^{CODESYS Forge talk (Post)}
Hi, I am new to modbusTCP and I am trying to access Input registers from codesys (3.5.SP13). The offset is 16#0000 and I am trying to access Channel 1[24] %IW24 to pull analog values. I am using pyModbusTCP and I need to supply a modbus address and the number of registers to read. What does 16#0000 mean in terms of the actual offset, how do I translate this number plus the channel to access this info via python? Any help would be appreciated, thank you.
Last updated: 2023-09-20

Sort by relevance or date