Post by andrax on CodeSys Raspberry pi I2C driver not found ^{CODESYS Forge talk (Post)}
I took a look at your project. First of all, a Raspbery Pi4 is installed. You must use the GPIOs_A_B(GPIOs B+/Pi2). The error ULINT can't be set to IDINT.... with your project as well. If I change your project to ‘CODESYS_Control_for_Raspberry_Pi_SL’ the error is gone.
Last updated: 2024-11-09

Post by andrax on CodeSys Raspberry pi I2C driver not found ^{CODESYS Forge talk (Post)}
Sorry, wrong expression. You have a 64bit system, so do I. You can also use the 64bit runtime, but most bib and commands are 32bit and are not properly supported. I had read somewhere that there are problems with I2C. That's why I recommend switching to PI_SL and using the correct gpio.
Last updated: 2024-11-09

Post by timvh on Leitungsverzweigung mit einem existierenden Block (z.B. AND-Glied) zu verbinden ^{CODESYS Forge talk (Post)}
If you are really happy with PLCnext engineer, then just use that. There is probably also something in CODESYS that cannot be done in PLCnext engineer. But if you are forced to make something like this in CODESYS, then maybe just use CFC instead of FBD.
Last updated: 2024-11-11

Post by rafaelbrito on Integration C Code ^{CODESYS Forge talk (Post)}
I tried to use C code in the library that I have been developing in the project, but without success. I tried to use the CODESYS Control SL Extension Package to generate XXXdep.h and XXXltf.h, but without success. Do you have a better example of how to generate these files and how to compile them?
Last updated: 2024-12-03

Post by rafaelbrito on The element of type 'VisuFbElemImage' could not be updated. Reason: Index was outside the bounds of the array. ^{CODESYS Forge talk (Post)}
When trying to use the Visualization ToolBox, no objects appear and the following error appears. Could you tell me what this error could be? The element of type 'VisuFbElemImage' could not be updated. Reason: Index was outside the bounds of the array. Can anyone tell me what this error is?
Last updated: 2024-12-03

Post by dkugler on EtherCAT Master: How many error frames till bus error ^{CODESYS Forge talk (Post)}
The story behind: I have had a EhterCAT fieldbus system where sometimes error frames occured. I noticed that the master is tolerant for some error frames, but if there are very much error frames the bus goes in error state. Does somebody know the limit of error frames above the bus changes to error state?
Last updated: 2024-12-03

Post by hyys12 on Energie price ^{CODESYS Forge talk (Post)}
I am definetly not an expert in this field, but it does seem like you need a propper API key in the URL. Right now you are using the token 'ANWB' in your URL, which the website returns an error, since this is not valid. Somehow you first need a propper API key. I hope that makes sense.
Last updated: 2024-12-06

Post by xabier on Kinematics Robot Delta 2 Axis ^{CODESYS Forge talk (Post)}
Hi, I have a customer and this customer design this robot...The customer need move ...I would like if Codesys has this Kinemtaics I attached photo of the robot.(this robot has 2 Axis) I have checked all kinematics has Codesys but not has the same....Someone help me Please?? Thanks XABI
Last updated: 2024-12-11

Post by daniel on Codesys Tools Update Raspberry ist nicht vorhanden aktualisieren im Geraete ansicht geht auch nicht ^{CODESYS Forge talk (Post)}
Guten Tag, ich habe das gleiche Problem nur mit der 20.4 Version. Über den Installer habe ich alles installiert allerdings erscheint bei mir unter Tools nicht die Möglichkeit den Raspberry zu aktualisieren. Mit der 19.7 habe ich das gleiche Problem. Muss noch etwas anderes installiert werden? Kann mir jemand weiterhelfen? Grüße Daniel
Last updated: 2024-12-13

Post by durallymax on Help understanding analog in-/outputs ^{CODESYS Forge talk (Post)}
WAGO will use 0-32767 as the raw units. Note a value of 3 means over/under range. Map that IO however you please, then scale in your program using any of the available libraries or with your own simple y=mx+b scaling formula to get to the engineering units you desire. Inverse for the AO to get back to 0-32767.
Last updated: 2024-12-15

Post by bjarne-pagaard on Newly created texlists wont appear in the selection dropdown ^{CODESYS Forge talk (Post)}
I just had the same problem in 3.5 SP19 Patch 6. Trying to use a textlist for Combobox Integer element. The textlist cannot be selected in the IDE, and is not found when manually entering the name. The textlist is copied to the device, but is not used. Can confirm, that copying an existing textlist and renaming it does work.
Last updated: 2024-12-16

Post by totorovic on Project loses 'Download time' information ^{CODESYS Forge talk (Post)}
I continue this topic by myself, I'm very happy with the Codesys support / community ;-) This information (Download time) should be stored in the compileinfo : https://content.helpme-codesys.com/en/CODESYS%20Development%20System/_cds_cmd_load.html But the file is not text-readable (see attached file) so how to solve if download time is empty?
Last updated: 2024-12-19

Post by mtnkyr on Runtime Problem connecting to Keyence IV-500MA Camera ^{CODESYS Forge talk (Post)}
I have to use Keyence IV-500MA Camera for a project. Actually I can use physical connection but I tried to connect using Ethernet protocol so I added its EDS file but I took a lot of errors. Could you help me to solve this problem?
Last updated: 2024-12-26

Post by mtnkyr on Runtime Problem connecting to Keyence IV-500MA Camera ^{CODESYS Forge talk (Post)}
I have to use Keyence IV-500MA Camera for a project. Actually I can use physical connection but I tried to connect using Ethernet protocol so I added its EDS file but I took a lot of errors. Could you help me to solve this problem?
Last updated: 2024-12-26

Post by conny-nm on Bosch BME 280 bzw 688 Sensor per I2C Bus steuern und Daten in Codesys verarbeiten ^{CODESYS Forge talk (Post)}
Hallo Markl, gibt von Stefan Dreyer auf Git Hub Biblioteken für BMP280 und BME280, laufen aber nur in 32Bit auf dem Raspberry. BME680 kann man mit Node Red auslesen und mit mqtt zu Codesys übertragen.
Last updated: 2025-01-07

Post by winki on Not Possible to connect using control SL ^{CODESYS Forge talk (Post)}
Hello, I used to connect into my gateway using control SL tool 4.13, (it was called Update Linux.) I formated my computer, so today I install the new version of codesys and all package. Now I am not able to connect to my PLC using control SL. It says, check the status. Normally it used to worked perfectly before that.
Last updated: 2025-01-07

Post by timvh on Colors look different when logged in and running ^{CODESYS Forge talk (Post)}
At the top of the Visualisation Properties View, you can enable the "Advanced" options. This will give you access to more properties than what you currently see. There might be a variable linked to the "advanced" colour property where the fill colour is determined by the value of this variable (dword).
Last updated: 2025-01-09

Post by timvh on Library ENUM text representation in visualization ^{CODESYS Forge talk (Post)}
Probably the enum from the library doesn't have text support. In that case you need to add your own TextList to the application. In the rectangle you should use the property "dynamic text" to link this object to the textlist which you have created yourself and then link the text index to your enum variable.
Last updated: 2025-01-09

Post by gseidel on Strange problem with the ‘MC_SetPosition’ function ^{CODESYS Forge talk (Post)}
Hi Gustavo, can you reduce the problem to a project that reproduces the issue without the real servo drives? (You could set the servo drives to virtual and strip away as much as possible from the application.) If you can attach a project, we will have a look. Best regards, Georg
Last updated: 2025-01-10

Post by ekristoffe on Modbus UDP ^{CODESYS Forge talk (Post)}
UDP has no packet ordering mechanism, and Modbus protocol has no order checking mechanism nor session establishment. I'm sorry but this is false, Modbus IP based have the Transaction Identifier. Transaction Identifier - It is used for transaction pairing, the MODBUS server copies in the response the transaction identifier of the request. Modbus UDP make more sense than Modbus TCP in a local environment.
Last updated: 2025-01-14

Post by pernockham on Preferred way of managing Ip-adress/es for linux (debian) host? ^{CODESYS Forge talk (Post)}
I have a debian linux host running Control SL. I tried to manage IP-addresses through codesys/Control SL but that was not successful. What works though is manually editing the network-interfaces config file. /etc/network/interfaces. Is there a way to set this up so that IP-addresses can be managed from within codesys instead? Thanks! / Per
Last updated: 2025-01-22

Post by jddaigle on Webvisu not supported due to missing browser feature HTML5-Canvas ^{CODESYS Forge talk (Post)}
Hello, I'm running the lastest version of Codesys 3.5 SP20 Patch 5, with the lastest version of Chrome. And I still get this "Webvisu not supported due to missing browser feature HTML5-Canvas" fallback with a quite simple webvisu containing some buttons, images, textboxed and a grid. What can I do? is that a configuration to change? Thanks!
Last updated: 2025-01-24

Post by imdatatas on Problem with edge gateway config mode ^{CODESYS Forge talk (Post)}
I encountered the same problem. (Windows10 x64 single language OS). As @eschwellinger mentioned, I uninstalled the latest EdgeGateway version and installed version 3.5.20.0. Now, when I right-click and select "Allow Edge Gateway...", Config mode is activated without any error or warning window and I do not need to manually type [CmpEdgeGateway] for EdgeGateway version 3.5.20.0.
Last updated: 2025-02-04

Post by mubeta on UNION statement is not supported in the ethercat data exchange ^{CODESYS Forge talk (Post)}
Hi all, I am using a unionn statement for merge in integer data type some values that are received in byte from the i/o cards, but, using this simple and light technique, is not recognized by the ethercat data exchange and in fact the tags are not updated. In my opinion it's a very big bug.
Last updated: 2025-02-05

Post by spiritcore on Server not adding PLC ^{CODESYS Forge talk (Post)}
I added new Gateway and I can see it connected. When I scan the server for PLC, it finds the PLC but when I click the Add To Server button, it shows "PLC was added." in the status. But I can't find the PLC in the list. I tried removing the gateway and re-configure everything again but it didn't solve. Any ideas?
Last updated: 2025-02-17

Sort by relevance or date