Post by nz-dave on ethercat softmotion axis error ^{CODESYS Forge talk (Post)}
Hi all I'm having a little trouble get my axis to work. i can turn them off and on. i can run each servo manually inputting directly to the mapping address. as soon as i try to use any FB's like jog etc my servos wont move and error out. so far I've had error "SMC_ERROR.SMC_DI-POSITIONLAGERROR" and another one about not calling a fb. cheers. in the attachment I have just jogged X_Axis with the MC_JOG FB
Last updated: 2025-03-10

Post by trusty-squire on Ethernet/IP Scanner Exception ^{CODESYS Forge talk (Post)}
What is the task configuration? When you are online and look at the task monitor, what does it show? (Put a screenshot here). If the processor is overloaded you'll likely need to increase the cycle interval, disable the watchdog, or change to a cyclic task instead of interval based? Also, You might want to adjust your task priorities so they don't all have the same priority. Just a few thoughts, although looking at the task monitor would help in troubleshooting.
Last updated: 2025-03-12

Post by atone on Change IO-Link Device Interface connected to a Profinet-Slave at Runtime ^{CODESYS Forge talk (Post)}
I need to be able to update (change) the interface of an IO-Link device at runtime. The reason is the connected sensor can be selected at runtime, and some sensors we use have a 2 byte IN interface, others have a 4 byte IN interface, others 16 byte IN, others 16 byte IN/OUT (see attached screenshot). Is it possible at all? When yes, which function should I use? Thank you!
Last updated: 2025-03-18

Post by nz-dave on Ethernet/IP Scanner Exception ^{CODESYS Forge talk (Post)}
Hi Trusty-Squire, just seen you post , thanks for the reply. I was out on site the other day as it had done it again and changed a few things like cycle time etc. plc load is only 7% at its highest. I took a few screenshots while i was there to add to this post. its been up for about a week now but seems to happen at random every couple of weeks. fingers crossed!
Last updated: 2025-03-19

Post by atone on Set DeviceID of an IO-Link Sensor at Runtime ^{CODESYS Forge talk (Post)}
I need to be able to change (set) the DeviceID of an IO-Link sensor (see DeviceID.png) at runtime. I tried with both ProfinetCommon.PN_PortConfiguration and ProfinetCommon.IOL_PortConfiguration, but I get an error for both when I try to read the port configuration (see PN_PortConfiguration.png). Does one of those FBs is the right one for my purpose? Do I possibly make a mistake when assigning the parameter IOLD_ID/IOLM_ID?
Last updated: 2025-03-19

Post by marks on Siemens G120X via Ethernet/IP ^{CODESYS Forge talk (Post)}
The goal is to control a Siemens G120X VFD via Ethernet/IP. The .eds is installed into the device repository. The VFD is added and is using the connection and assemblies from the eds. It appears to reach the VFD but fails to establish a connection. The status message is: Diag String: 'Adapter configured. Open all connections.' The PLC is a raspberry pi 4, running codesys target version 4.13.0.0. The development environment is CODESYS V3.5 SP21 + (64-bit). Anyone have experience with this combination? Alternately, where should I look next? Thank you, Mark
Last updated: 2025-05-06

Post by janp on IFM Controller Connection Issue ^{CODESYS Forge talk (Post)}
Hi everyone, I’m using an IFM ecomatBasic CR413S controller and having trouble connecting it to CODESYS 3.5. I have CODESYS SP18 installed, as recommended in the manual, and I’ve tried different patches. I’ve also installed all the packages provided on the IFM website for this controller. I can successfully connect to the ecomatBasic template, but I’m unable to connect when using the CR413S-specific template that includes all the inputs and outputs. Has anyone encountered this issue or knows a solution? Best regards, Jan
Last updated: 2025-05-22

Post by janp on IFM Controller Connection Issue ^{CODESYS Forge talk (Post)}
Hi everyone, I’m using an IFM ecomatBasic CR413S controller and having trouble connecting it to CODESYS 3.5. I have CODESYS SP18 installed, as recommended in the manual, and I’ve tried different patches. I’ve also installed all the packages provided on the IFM website for this controller. I can successfully connect to the ecomatBasic template, but I’m unable to connect when using the CR413S-specific template that includes all the inputs and outputs. Has anyone encountered this issue or knows a solution? Best regards, Jan
Last updated: 2025-05-22

Post by ggis on Manage Gateways between different CODESYS IDE versions ^{CODESYS Forge talk (Post)}
Hi, I'd like to share the list of gateways between different versions (and sandboxes) of Codesys IDE. I refer to the list that is managed in Device > Communication Settings (as described in https://content.helpme-codesys.com/en/CODESYS%20Development%20System/_cds_edt_device_communication_settings.html ) Can I export/import that list? Or is there a file that I can copy from one installation to another one? Thank you GG
Last updated: 2025-05-28

Post by eschwellinger on CODESYS Control for Linux ARM SL (32 bit) on Moxa UC-3100 IPC ^{CODESYS Forge talk (Post)}
I would recommend to ask Moxa for a newer version of Debian. Debian 9 ("Stretch") has reached its end of life and is no longer receiving security updates from the official Debian Security Team as of June 30, 2022. This means any systems still running Debian 9 are vulnerable to security risks and should be upgraded to a newer, supported version of Debian like Debian 10 ("Buster") or Debian 11 ("Bullseye").
Last updated: 2025-07-14

Post by fschuler on No connection to Raspberry at runtime installation ^{CODESYS Forge talk (Post)}
Hi, I try to install the Codesys realtime in a Raspberry PI 3B+. When I click on the installation button I get always the message No connection to device: An established connection was aborted by the server. Raspberry 3B+ with newest raspberry PI OS. Codesys 3.5.15 Patch 1 Codesys Runtime Package 3.5.16.20 SSH is activated. I can login with Putty Ping is possible IP address search is possible Just the installation is not started.
Last updated: 2025-07-23

Post by arwie on Working on exporting/importing projects to PlainText. ^{CODESYS Forge talk (Post)}
To better track project changes in git I created a script that exports the project structure as text files. Textual POUs are stored as text, everything else as XML (with timestamps removed). The file structure is stored under path/to/your.project.txt Git merge will not work, but at least tracking changes is much easier. Script: https://github.com/arwie/controlOS_demo/blob/main/codesys/txtfy.py Example output: https://github.com/arwie/controlOS_demo/tree/main/codesys/controlOS_demo.project.txt
Last updated: 2025-07-24

Post by jampid on Codeys Ladder LD2 ^{CODESYS Forge talk (Post)}
Hi, Has anyone managed to use the last four buttons in a POU toolbar in LD2? You can close and open by clicking from one small rectangle to another (same for deleting a closure //). Linking K to D causes a series connection with all the branches // above. Amazing! I don't really see the advantages of this supposedly modern and efficient language over the old LD/FBD. Can anyone explain?
Last updated: 2025-07-24

Post by timvh on I want to show the current recipe name in the visualization screen ^{CODESYS Forge talk (Post)}
Maybe the easiest solution for you is to add one STRING variable to your recipe and enter the name of the recipe in variable value. This is little bit double the work (naming the recipe and entering the value of the STRING variable), but in that case you always have the current value of the variable which you can read from the application and show in the visualization.
Last updated: 2025-09-04

Post by bmatlove on AXIS_REF_SM3 Error Codes? ^{CODESYS Forge talk (Post)}
I'm trying to firm up alarming of axis faults. Declutter the code and figure out what's what. Diving into it, I see the AXIS_REF_SM3 function block provides uiDriveInterfaceError and dwErrorId, but I can't find any significance of these further than Drive interface error number Parameter number: 1014 and Drive specific error identifier, parameter number: 1031, respectively. Is there some corresponding appendix I could use to decode these? Also, is there any relation to the Error ID (of type SMC_Error) of the MC POUs? MC_Jog, MC_Reset, MC_MoveRelative, etc? If so, are the above errors redundant? Thanks in advance.
Last updated: 2025-09-22

Post by nathant on Some visualization objects disappear when user is logged in? ^{CODESYS Forge talk (Post)}
I am deploying a webvisu on Codesys 3.5 SP 19.2 with legacy user management. I noticed that when a user logs in, some text and a rectangle I have (for aesthetics) both disappear. I made sure that none of the objects in question are linked to a state variable. Anyone know the cause/solution to this? Nothing crucial to the machine's function is lost, but it is a little annoying.
Last updated: 2023-12-15

Post by svn123 on In Simulation Mode, logic is not executing ^{CODESYS Forge talk (Post)}
Please check the attached snapshot. I am converting an int to real and storing in rVlv01_SV and then scaling the value using LIN_TRAFO. In the bottom Status Bar of Codesys, both RUN and SIMULATION are visible. When I enter value 100 as input to INT_TO_REAL instruction and press Ctrl-F7, the value can be seen at the input but the logic seems not to work. I searched for help but could not find anything relevant. What could be the reason. Codesys ver3.5.11 svn
Last updated: 2023-12-25

Post by toby on Codesys Control Raspberry PI 4.10.0 - missing 'Update Raspberry PI' option ^{CODESYS Forge talk (Post)}
Hi Edwin, Thanks for the message. My apologies I should have researched this more thoroughly before posting on here. I found a solution to my issue on this post: https://forge.codesys.com/forge/talk/Runtime/thread/6455efaa17/ I needed to run the 'CODESYS Installer' as an Admin, then install the RPi package v4.10.0 in to my package (v3.5 SP19 Patch 5). Thanks, hope you have a good day. Toby
Last updated: 2024-01-09

Post by rpostwvu on Shared Memory Access Issues ^{CODESYS Forge talk (Post)}
I got the shared memory example. I'm pretty sure I'm successfully created a memory space, CreateResult returns 18. szName:='CodesysDataShare'; hShm := SysSharedMemoryCreate(szName, 0, ADR(uxiSize), ADR(CreateResult)); I'm trying to access this memory with a C# application, but I get "Unable to Find Specified File". I suspect that Codesys and/or Visual Studio code alters the name I choose? Being in Windows, I cant find a way to see the mapped memory list. ~~~ using (var mmfRead = MemoryMappedFile.OpenExisting("CodesysDataShare",MemoryMappedFileRights.ReadWrite)) ~~~
Last updated: 2024-01-29

Post by ofey on two different OPC clients with different privileges ^{CODESYS Forge talk (Post)}
Hi! I have usually only connected one OPC client (our system) to an OPC server created in the codesys environment on a PLC. This OPC client has a lot of write privileges. A customer also want OPC access, but I want to restrict his access to only read certain values. Do you know if this is possible inside the single codesys runtime running on a controller?
Last updated: 2024-02-01

Post by jshirazi on Restore license on Raspberry Pi ^{CODESYS Forge talk (Post)}
Hi, I recently got a license for Raspberry Pi, after license activation I made a backup copy of "CMLicenseNew.WibuCmRaU" file to a safe place. Things got complicated and I tried to downgrade OS for some reason after that I tried several times/ways to restore my license with no luck. the specifications are as follows: Raspberry Pi 4 Model B Rev 1.1 codesyscontrol 4.10.0.0 SDK 3.5.19.30 Logs: **** ERROR: CodeMWriteLicenseFile: 'CMLicenseNew.WibuCmRaU' failed: Container not found or Server dose not support .... So if someone know a solution for this please kindly help me. Regards
Last updated: 2024-02-03

Post by jinlee on Multiple WebVisu ^{CODESYS Forge talk (Post)}
Hi, thank you for replying. Basically, I have a main visu with frame selection. So, under some condition the frame will switch to a specific frame. It used to be controlled by variable using "Switch frame variable". However, I realise it will change all the HMI screen at one time. So I removed the variable, and still looking for a solution to do that. Do you have any idea?
Last updated: 2024-02-06

Post by nmcc on Toggling Visualizations using HMI Physical Buttons ^{CODESYS Forge talk (Post)}
Hey thank you for the reply dkugler. I am sorry if this seems like a stupid question. I have the use current visuvariable checkbox enabled. I can see the string names of all my visualizations. I am trying to use ladder logic to be the anser to the button press using "VisuElems.CurrentVisu := 'MainScreen';. This returns an error. Any idea what I am doing wrong or could you point me in the right direction for fixing this. Thanks,
Last updated: 2024-02-13

Post by nmcc on Toggling Visualizations using HMI Physical Buttons ^{CODESYS Forge talk (Post)}
Hey thank you for the reply dkugler. I am sorry if this seems like a stupid question. I have the use current visuvariable checkbox enabled. I can see the string names of all my visualizations. I am trying to use ladder logic to be the anser to the button press using "VisuElems.CurrentVisu := 'MainScreen';. This returns an error. Any idea what I am doing wrong or could you point me in the right direction for fixing this. Thanks,
Last updated: 2024-02-13

Post by amy123 on CSV Utility CANNOT_OPEN_DIRECTORY ^{CODESYS Forge talk (Post)}
Hello, I tried using the CSV Utility SL Example from the CODESYS IIoT Libraries SL. No matter what path I try, I can not get the InitSave to work from CSVWRitersSTExample, line 2. It always gives the error 'CANNOT_OPEN_DIRECTORY'. I am running this on an Windows Azure VM, with Codesys Control Win V3 x64. I added a folder called 'temp' to my C: so that the default 'C:/temp' would work. However it gives CANNOT_OPEN_DIRECTORY. I tried updating to 'C:\temp' with the same result. Any help would be greatly appreciated!
Last updated: 2024-02-14

Sort by relevance or date