Post by albzen on EtherCat Slaves diagnosis ^{CODESYS Forge talk (Post)}
Hello everybody, I'm working on a RunTime Plc (Codesys 3.5.16/18.20) connected to an EtherCat bus with many devices. The bus has some communication fault but I don't know how understand which is the device or the cable that has the trouble. To understand the cause of the problem I would like to read the WKC (Working counter) of the devices (0x0300...0x030C), how is explained in EtherCat documents, but it seems that the read of the counter is disabled. Attached there is an extract of the Ethercat document. Can anyone give me some advice about how and with function can I read it. Thank you in advance!
Last updated: 2024-03-29

Post by albzen on EtherCat Slaves diagnosis ^{CODESYS Forge talk (Post)}
Hello everybody, I'm working on a RunTime Plc (Codesys 3.5.16/18.20) connected to an EtherCat bus with many devices. The bus has some communication fault but I don't know how understand which is the device or the cable that has the trouble. To understand the cause of the problem I would like to read the WKC (Working counter) of the devices (0x0300...0x030C), how is explained in EtherCat documents, but it seems that the read of the counter is disabled. Attached there is an extract of the Ethercat document. Can anyone give me some advice about how and with function can I read it. Thank you in advance!
Last updated: 2024-03-29

Post by alexgooi on Modbus writing on value change ^{CODESYS Forge talk (Post)}
The way I usally tackle this is by syncing only words (then you are able to use the FB above). If you then want to write a Boolean simply type it like this. Value[1].0 := Bool1; Value[1].1 := Bool2; Value[1].2 := Bool3; Uints have the same number of bits than a INT/WORD so these ones will work as well (they are only represented diffrently). A Real will work but you will loose some infomration in the conversion. If you want to keep the information you can convert 2 words to a float with a function (for example with the IEEE-754 standard) . In this way the syncing to the server is very simple and in the Codesys Program you decide what part of the word you want to use.
Last updated: 2024-04-03

Post by danwoodlock on Rpi zero w lost license after 4.11 update ^{CODESYS Forge talk (Post)}
Hello all, Encountered an issue with my zero which seems to have happened after the 4.11 update. It now runs in demo mode (2hr) and I am trying to see what the appropriate steps are prior to contacting codesys directly. Background: I recently did a fresh install of w11 on my pc, so it seems "c:\ProgramData\CODESYS\Licenses\" only has information related to my pi5, which I licensed just this past Friday. I have all my license documentation about my rpi zero as far as the emails received, but when I try to claim using the ticket number it says its already been used, or something to that effect, which it was. Currently trying to perform device license reader, which is taking some time.
Last updated: 2024-04-14

Post by saugat10 on Cannot install Codesys control Multicore in raspberry pi 4 ^{CODESYS Forge talk (Post)}
I have raspberry pi 4 with Raspbian 12 (bookworm). I want to install the latest version of codesys control 4.11.0.0 multicore for 32 bit. I cannot install multicore and it only gives me the option to install Standard. Here are some outputs from the pi pi@saugat:/usr $ uname -a Linux saugat 6.6.20+rpt-rpi-v7l #1 SMP Raspbian 1:6.6.20-1+rpt1 (2024-03-07) armv7l GNU/Linux pi@saugat:~ $ cat /etc/os-release PRETTY_NAME="Raspbian GNU/Linux 12 (bookworm)" NAME="Raspbian GNU/Linux" VERSION_ID="12" VERSION="12 (bookworm)" VERSION_CODENAME=bookworm ID=raspbian ID_LIKE=debian HOME_URL="http://www.raspbian.org/" SUPPORT_URL="http://www.raspbian.org/RaspbianForums" BUG_REPORT_URL="http://www.raspbian.org/RaspbianBugs" A
Last updated: 2024-04-22

Post by ac-spr on Runtime variable that indicates a user is online to the code ^{CODESYS Forge talk (Post)}
Looking to access a variable at runtime that indicates a user is online to the code. essentially want to use this value to feedback to the user on the HMI. we use turck and bosch rexroth devices if this information helps. I was hoping there was a variable at the application level, or a library that could be used but I was unable to find anything. I know there's a pop up when you try to login/ go online to the code when a user is already logged in, so the system does provide an indication that it knows already online, but has no access to a value from what I can see. Any help is appreciated
Last updated: 2024-04-22

Post by gseidel on CNC / G01 Speed is very slow (or go-stop motion) in Continuous short segment . ^{CODESYS Forge talk (Post)}
Hi k2saki, I would recommend to have a look at SMC_SmoothMerge, followed by SMC_SmoothPath. SmoothMerge will combine the small G1 elements to longer splines, SmoothPath will avoid stops between the splines. https://content.helpme-codesys.com/en/libs/SM3_CNC/Current/SM_CNC_POUs/SoftMotion-CNC/SoftMotion-Function-Blocks/SMC_SmoothMerge.html For SmoothMerge to work, you have to configure a tolerance, i.e. by how much it may deviate from the lines. To graph the output of the interpolator, you can use the trace. (Add a trace object below the application, and add the variables you are interested in to the trace.) Best regards, Georg
Last updated: 2024-04-30

Post by jonasz on Discontinuity of A/B/C axis movement. ^{CODESYS Forge talk (Post)}
Hi, My problem was related to the behavior of the modulo axis, but maybe you will find something useful from what I write. The solution lies in path processing. Codesys offers a G-code analysis tool. Insert a CNC object into the project. The CNC settings object will be added automatically. By inserting appropriate processing modules into the CNC settings object and parameterizing them, you can test the behavior of the axis. When the effect is satisfactory, remember to add the module from CNC settings in the correct order in the processing path. Each CNC machine case is different. You need to spend some time to get your design tailored like an Armani suit. Good luck.
Last updated: 2024-05-09

Post by fugtwad on Automation Builder V2.5 EtherCAT CM579 Master Scan for devices - >No gateway selected ^{CODESYS Forge talk (Post)}
ABB Automation Builder v2.5.0.22 Premium CodeSys 2.3.9.62 Running on Win 10 VM x64 Goal: I have an EtherCAT topology issue which normally a "Scan for devices.." on the EtherCAT master would shed some light on. Issue: Upon trying such I get a "No gateway selected" error. Question: How might I point the the "scanner" at a gateway? What is working: Gateway is running in system tray. I can go online to PLC. A scan from the "Diagnostics live" tab of the EtherCAT master gives slave status. What I have tried: Restarting gateway in system tray. Exiting system tray gateway and reloading it. Turning off firewall. Contacting ABB support multiple times. Any help appreciated.
Last updated: 2024-05-20

Post by matt-purcell on Which Lib to use, connect to a socket with URL instead of IP address ^{CODESYS Forge talk (Post)}
Hello, I have a new project and I need to connect to a TCP socket using the URL instead of an explicit IP address, myendpoint@mydomain.com Which library is best suited for this? This is for a new enterprise project, the endpoint is a server in a datacenter running some real time application. We have big IP, it will automatically reassign the IP address to the backup server if a crash occurs so an explicit IP won't work for me. I've done this in RS logix, working now to migrate that code over to codesys. Thanks in advance!
Last updated: 2024-06-17

Post by ppix on Establishing TLS Connection with MQTT Broker using MQTT Client SL Package ^{CODESYS Forge talk (Post)}
For anyone confused with the process visit this link (the bottom section about creating a .pfx file) https://content.helpme-codesys.com/en/LibDevSummary/certificate.html#import-of-client-certificates-with-private-key. I solved this problem by creating a .pfx file and importing it into the security store under 'Own Certificates'(must have SP18 or newer to import .pfx). I used a gitbash shell to enter the openssl command that created the .pfx file. Once you import the file, in your TLS context, set your 'sUseCaseName' to be the same as the name listed in the 'Information' column of your imported certificate. This did it for me
Last updated: 2024-06-20

Post by jonasz on Deploy LicenseServer for Linux SL ^{CODESYS Forge talk (Post)}
The machine I'm currently using (Celeron J1900) already has the Kernel RT patch. I checked the performance according to the documentation. After running CyclicTest for 4 cores, the value for each core is around 6-7. I went through the entire process according to the documentation (I envy the TaskMonitor results in the documentation). The documentation states: "CODESYS Virtual Safe Time Provider The CODESYS Virtual Safe Time Provider is a standard interface that the user can use to transfer a second and external time base to the CODESYS Virtual Safe Control. The implementation is done as a client, which must run on another system with an independent time base." How do I implement this? I've been struggling for two weeks now - I'm too old to give up.
Last updated: 2025-11-17

Post by sheberle on No Bootproject possible ^{CODESYS Forge talk (Post)}
Hello Alex, the message is generated by the CODESYS code generator based on the DevDesc settings of the memory areas available for the target. The problem arises when after too many online changes the area is full. Therefore no more boot project can be generated. Short-term remedy as described in the dialog: Clean and fresh download. This way the initial memory size will be "used" again After how many online changes did this error occur? There is no set limit on the number of online changes, but making too many changes could be a risk. br Simon
Last updated: 2026-03-31

Post by timvh on EXCEPTION [watchdog] how to find position cause ^{CODESYS Forge talk (Post)}
Monitor what your current cycle time is (in the Task Configuration when you are online). If this is sometimes close to 200ms, then change your code (e.g. limit the loops, or prevent copying a lot of data between objects). Or just set the Watchdog time (or sensitivity) higher if you don't care that it sometimes takes longer than 200ms. If you want to find out which objects in your application consume the most time, then buy a PDE (Professional Developer Edition) license. With this you get a license for the Profiler. This can help you a lot to find the root cause, because it will create a nice overview of all objects, their calls and the time (percentage) it takes to execute it.
Last updated: 2026-02-09

Post by kporter on Codesys EtherCAT Driver (CmpEt1000MPD) can't set MAC address ^{CODESYS Forge talk (Post)}
EtherCAT is a point-to-point protocol so it doesn't need a unique MAC address. It would be very useful to set the MAC address to 020000000000, the standard address for this kind of application. (The important bit is the 02 at the start of the address, which means locally-administered MAC.) The stock Windows driver can do this for my i210 card. But the CODESYS CmpEt1000MPD driver cannot. The image shows the setting with the Windows driver. If I set all my customers' cards to this address, then I don't need to deal with this when deploying my application. A simple PowerShell script can be used to set the MAC address once when the NIC is installed and the driver is changed.
Last updated: 2026-02-09

Post by yannickasselin on Question about Demo License limitations for Modbus TCP communication and Fieldbus Instances ^{CODESYS Forge talk (Post)}
As far as I know, there is no other limitations than the 2 hours limit. The demo mode should be plenty enough for testing purposes. Regarding instances. In the device tree, 1 master = 1 instance, no matter how many slaves the master is communicating with. But it is also possible that your Codesys runtime act as a slave. In this case, each slave in the device tree is one instance. You can also use the license metric tool in the IDE. This will tell you exactly how many instances you have in your project. https://content.helpme-codesys.com/en/CODESYS%20Development%20System/_cds_edt_device_licensed_software_metrics.html
Last updated: 2026-02-28

Post by gordonkeller360 on Escape character behavior for hex values in string -- what gives? ^{CODESYS Forge talk (Post)}
I have a program which sequentially places byte representations of characters from a string into an array. FUNCTION_BLOCK MoveBytesFromString VAR_IN_OUT abRxBuf: ARRAY [0..79] OF BYTE; END_VAR VAR testString : STRING := '$0A$R$L$TTesting,123...$94$86$0A'; iCount: DINT; END_VAR ---------------------------------------------------------------------------------------- // clear the buffer MEM.MemFill(ADR(abRxBuf), 80, 0); FOR iCount := 0 TO LEN(testString) - 1 DO // account for undesired null terminator of string abRxBuf[iCount] := testString[iCount]; END_FOR Escaped characters, like $T, $N, etc. work just fine, and so do their hex representation counterparts ($09, $0A, etc). However, when I put something like $94, I get a set of nonsense values... see image attached after one spin of the program. Could someone explain to me what is happening here? I'll continue to investigate...
Last updated: 2026-03-09

Post by thierry-b on CODESYS device discovery performance in large networks (/16) ^{CODESYS Forge talk (Post)}
Hello, We are using CODESYS 3.5 SP19.70 in an educational environment with several WAGO PFC200 controllers (CODESYS Runtime). Our campus network is currently configured as a /16, which creates a very large broadcast domain. We observe slow device discovery and long scan times when opening the network view. Before restructuring our architecture, we would like to know the recommended network practices for CODESYS: Recommended broadcast domain size for device discovery Possible impact of large networks (/16) on scan performance Usual recommendations (VLANs, /24 segmentation, etc.) Known limitations or points of attention in extended networks Any guidance or official recommendations would be very helpful. Thank you.
Last updated: 2026-03-29

Post by msegon on Send HTML body with Mail Service SL ^{CODESYS Forge talk (Post)}
I'm trying to send a mail using Mail service SL. I would like the body to be in HTML format for a nicer look. Which I managed to do, but only if I don't send an attachment. Can someone help me with the settings on how to send an HTML body and attachment? I used the Mail Service SL Example project, the only thing I added in the "Main_PRG" code in line 51 under "SendMailFB" is "mimeType := 1". I'm using Library: Mail Service SL Library Documentation Company: CODESYS Title: Mail Service SL Version: 1.13.0.0 Categories: Application|Utils Namespace: MAIL Author: CODESYS Development GmbH Placeholder: Mail_Service_SL
Last updated: 2026-04-14

Post by vstrom on Codesys v3.5.22.10 - Fail to create a project Archive ^{CODESYS Forge talk (Post)}
Hi to all, I've created a project using the File->New Project-> Standard Project command. Then I've add the object "Visualization Manager" and then tried to create a project archive (File->Project Archive->Save Archive), but it fails with the error "Access to the path 'C:\Program Files\CODESYS 3.5.22.10\CODESYS\Common\3hxi4iod.put' is denied". The idicated file don't exist. First time of use of the new Codesys versionù, I've reinstalled the developement software but nothing change. If I don't add the Visualization part, the archive is created, it's seems to be a problem with the HMI part. Any ideas? Thanks
Last updated: 2026-04-22

Post by alexgooi on Network variable stops sending ^{CODESYS Forge talk (Post)}
Hi Reinier, What usually works for me is settings it up in the following way: In the sender block make sure that the list identifier is unique for the whole installation (this is only relevant when you have multiple senders in 1 network). When you are linking the NVL to a file make sure that the path to this file doesn't change. In my experience the NVL stops working when you change the working directory and afterwards open the NVL in de Codesys IDE. If this doesn’t apply to you application, you could also try to change the port number, maybe there is an other process making use of port 1202. Kind regards Alex
Last updated: 2026-04-22

Post by kurt9 on ReadWriteEEprom FB question ^{CODESYS Forge talk (Post)}
I want to programmatically write the alias address to a new EtherCAT slave when I plug it into my IPC EtherCAT network. I am looking at the ReadWriteEEprom FB and see that one of the elements is "pbyData". which is the pointer to byte that is usually set to 2048 bytes. Since I am setting the alias address to the EEprom only (EEprom address 16#0012), I would assume that what I am writing is 2 bytes only. Does the pbyData have to be specified as ADR(myArray) where "myArray" is the 2 bytes of the alias address? How is the best way to set this element of the function block? Thanks in advance
Last updated: 2026-05-18

Post by umdee on Error when monitoring LAD programs ^{CODESYS Forge talk (Post)}
I get the following error when monitoring my program (see attached screenshots): "Unhandled exception has occured in your application. If you click Continue, the application will ignore this error and attempt to continue. If you click Quit, the application will close immediately. Value cannot be null. Parameter name: source. And the details say: See the end of this message for details on invoking just-in-time (JIT) debugging instead of this dialog box. ** Exception Text ** System.ArgumentNullException: Value cannot be null. Parameter name: source at System.Linq.Enumerable.Any[TSource] (IEnumerable1 source, Func2 predicate) at _3S.CoDeSys.NWLEditor.NWLTextCell.OnPaintCellLayer(PaintEventArgs e) at _3S.CoDeSys.Controls.Controls.GfxEdControl.PaintCellCellLayer(PaintEventArgs e, GfxCell cell) at _3S.CoDeSys.Controls.Controls.GfxEdControl.PaintCellCellLayer(PaintEventArgs e, GfxCell cell) at _3S.CoDeSys.Controls.Controls.GfxEdControl.PaintCellCellLayer(PaintEventArgs e, GfxCell cell) at _3S.CoDeSys.Controls.Controls.GfxEdControl.OnPaint(PaintEventArgs e) at System.Windows.Forms.Control.PaintWithErrorHandling(PaintEventArgs e, Int16 layer) at System.Windows.Forms.Control.WmPaint(Message& m) at System.Windows.Forms.Control.WndProc(Message& m) at System.Windows.Forms.UserControl.WndProc(Message& m) at _3S.CoDeSys.Controls.Controls.GfxEdControl.WndProc(Message& m) at System.Windows.Forms.NativeWindow.Callback(IntPtr hWnd, Int32 msg, IntPtr wparam, IntPtr lparam) ** Loaded Assemblies ** (3000 lines of assemblies) ** JIT Debugging ** To enable just-in-time (JIT) debugging, the .config file for this application or computer (machine.config) must have the jitDebugging value set in the system.windows.forms section. The application must also be compiled with debugging enabled. For example: <configuration> <system.windows.forms jitdebugging="true"> </system.windows.forms></configuration> When JIT debugging is enabled, any unhandled exception will be sent to the JIT debugger registered on the computer rather than be handled by this dialog box The windows show red X's where the networks should be. Any advice on how to fix this? Additional Information PLC used: Wago 750-8212, Firmware FW26 Startup profile: CODESYS V3.5 SP19 Patch 5 OS version: Microsoft Windows NT 10.0.22631.0 .NET version: 4.0.30319.42000 Full Version info attached as .txt
Last updated: 2024-03-17

Post by anonymous on Hi, I try to send and receive data using a UDP connection via SysSocket 3.5.17.0. While sending data works fine, I have problems with the receiving part. I am able to capture the received data of client side in wireshark But unable to capture it on the codesys ^{CODESYS Forge talk (Post)}
Hi, I try to send and receive data using a UDP connection via SysSocket 3.5.17.0. While sending data works fine, I have problems with the receiving part.I am able to capture the data of client side in wireshark but i am unable to capture it in the codesys. Heres the below part of code of client side. PROGRAM POU_udpclient_program VAR istep : INT := 1;//step variable for state machine xStart: BOOL;// Flag to start the UDP protocol iecSocketId: syssocket_interfaces.RTS_IEC_HANDLE;//socket handle for receiving iecCreateResult: syssocket_interfaces.RTS_IEC_RESULT; ipAddr: syssocket.SOCKADDRESS;//Socket address structure for receiving sIpAddress : STRING := '192.168.0.2'; wPort: WORD:= 12346; iecConnectResult : syssocket_interfaces.RTS_IEC_RESULT;//connect paramters sDataRec : STRING[255];//Buffer for received data xiRecBytes : __XINT;//number of bytes received iecRecResult : syssocket_interfaces.RTS_IEC_RESULT;//receive data parameters iecCloseResult : syssocket_interfaces.RTS_IEC_RESULT; END_VAR syssocket.SysSockInetAddr(sIpAddress,ADR(ipAddr.sin_addr)); ipAddr.sin_family := syssocket.SOCKET_AF_INET; ipAddr.sin_port := syssocket.SysSockHtons(wPort); CASE istep OF 1: //create socket IF xStart THEN iecSocketId:= syssocket.SysSockCreate(syssocket.SOCKET_AF_INET,syssocket.SOCKET_DGRAM,syssocket.SOCKET_IPPROTO_IP,ADR(iecCreateResult)); IF iecSocketId = syssocket_interfaces.RTS_INVALID_HANDLE THEN xStart := FALSE; istep := 1; ELSE istep := 2; END_IF END_IF 2: //connect to socket server using setoption iecConnectResult := syssocket.SysSockSetOption(iecSocketId,syssocket.SOCKET_SOL,syssocket.SOCKET_SO_REUSEADDR,ADR(ipAddr),SIZEOF(ipAddr)); istep := 3; 3: //receive data xiRecBytes := syssocket.SysSockRecvFrom(iecSocketId,ADR(sDataRec),SIZEOF(sDataRec),0,ADR(ipAddr),SIZEOF(ipAddr),ADR(iecRecResult)); istep := 4; 4: //close socket iecCloseResult:= syssocket.SysSockClose(iecSocketId); xStart := FALSE; istep := 1; END_CASE
Last updated: 2024-06-03

Post by rossanoparis on After un upgrade of "CODESYS Control for Raspberry Pi MC SL" from v4.7 to v4.9 SysFileOpen function stopped working ^{CODESYS Forge talk (Post)}
Hello at all. After un upgrade of "CODESYS Control for Raspberry Pi MC SL" from v4.7 to v4.9 SysFileOpen function stopped working. I'm not able to read or write files from the PLC application. Before this upgrade all worked fine. I've read this thread [ https://forge.codesys.com/forge/talk/Engineering/thread/3da9ded84e/ ] Despite I followed that indications I couldn't get my code working again. Perhaps I'm missing something or I didn't understand how to use placeholders at all. Is there a different syntax to use for "SysFileOpen" in order to use placeholders? Thanks in advance for your help. Information Compiler: CODESYS V3.5 SP19 Patch 2 Runtime: codesyscontrol 4.9.0 HW: KUNBUS RevPi Connect S Below the paths I want to access (The entire CODESYSControl_User.cfg file is attached) [SysFile] PlaceholderFilePath.1=/home/pi/hpca/bin, $hpcabin$ PlaceholderFilePath.2=/home/pi/hpca/cfg, $hpcacfg$ PlaceholderFilePath.3=/home/pi/hpca/logs, $hpcalogs$ PlaceholderFilePath.4=/home/pi/hpca/resources, $hpcares$
Last updated: 2023-08-22

Sort by relevance or date