Post by gatto on Modbus tcp - channel ^{CODESYS Forge talk (Post)}
Hi can you give more details? Are you talking about a danfoss? wich model? Can post the configuration of channel' I used, on the past, serial modbus with danfoss fc280 I remember ((id x 10)-1) I remember that you couldn't use continuous reading/writing of the directors but you had to use them one at a time. it seemed that reading empty registers (caused by x10) was not accepted by danfoss. So I had created a scan that used just one register, then the next etc etc with a timed interval. But this was for the serial, I don't know if it's the same thing with ethernet. I currently use Ethernet TCP/IP interface with FC280.
Last updated: 2024-06-13

Post by timothyzalusky on Strange Behavior on Raspberry Pi ^{CODESYS Forge talk (Post)}
Hello, I am seeing some weird runtime behavior related to the EQ function on a rapsberry pi based system. I have attached a screenshot showing the strange latching I am seeing on the EQ function, and I have not seen this behavior before. I tried freshly restarting the runtime and it has this same behavior. Anyone seen this? I am on 3.5.20 with the latest runtime installed. Basically, as soon as it hits one of those EQ's in the program, it latches effectively locking the output on. Any input from the Codesys team would be appreciated as well as anyone that might know what I am seeing.
Last updated: 2024-06-18

Post by jasperclauwaert on Persistent Retain Variables Not Visible in Online View (WAGO PFC100 + CODESYS) ^{CODESYS Forge talk (Post)}
Hi everyone, I’m working on a WAGO PFC100 with CODESYS. During development everything worked fine, but in the final stage I set several variables to PERSISTENT RETAIN. When I go online, most of these persistent variables cannot be monitored. Instead, I see: <Value of the expression cannot be retrieved> Interestingly, a few variables do show their values correctly, but the majority do not. The variables are not used as pointers or in any unusual way. The application compiles and runs without errors. Has anyone experienced this before? Is this a known issue with PFC100 or CODESYS? Any ideas on what could cause this behavior? Thanks in advance! Jasper
Last updated: 2025-10-23

Post by jasperclauwaert on Persistent Retain Variables Not Visible in Online View (WAGO PFC100 + CODESYS) ^{CODESYS Forge talk (Post)}
Hi everyone, I’m working on a WAGO PFC100 with CODESYS. During development everything worked fine, but in the final stage I set several variables to PERSISTENT RETAIN. When I go online, most of these persistent variables cannot be monitored. Instead, I see: <Value of the expression cannot be retrieved> Interestingly, a few variables do show their values correctly, but the majority do not. The variables are not used as pointers or in any unusual way. The application compiles and runs without errors. Has anyone experienced this before? Is this a known issue with PFC100 or CODESYS? Any ideas on what could cause this behavior? Thanks in advance! Jasper
Last updated: 2025-10-23

Post by jeindhoven on Deploying to raspberry pi 5 hangs ^{CODESYS Forge talk (Post)}
Yep sure, though now that i think of it, its a pi 4. My bad. The whole ordeal was necessary to use the VGA666 adapter. That needs the old graphical system and GPIO directly on the CPU. Edit: Putty on the virtual development machine connects fine. But i did change the login/pw. The account is still a sudo'er so that should be all right. Edit2: Sorry i get a "Comment rate limit exceeded" from the forum. Then i'll add it as edit here. So i have tried the stock raspberry pi image on a different pi5 (truly 5 this time). Packages updated. Standard password. Same symptoms, no runtime deployed and long hang time. Versions of this pi: pi@raspberrypi:~ $ uname -a Linux raspberrypi 6.12.25+rpt-rpi-2712 #1 SMP PREEMPT Debian 1:6.12.25-1+rpt1 (2025-04-30) aarch64 GNU/Linux pi@raspberrypi:~ $ lsb_release -a No LSB modules are available. Distributor ID: Debian Description: Debian GNU/Linux 12 (bookworm) Release: 12 Codename: bookworm pi@raspberrypi:~ $ apt list --installed | grep openssh-server openssh-server/stable,now 1:9.2p1-2+deb12u6 arm64 [installed,automatic] Attached is the Device information and error text that Codesys comes up with. Edit 3 (Comment rate limit, otherwise it would be a new post) Now i have tried booting an older native Windows 10 machine (no virtualization), and it just works as expected. I have now a raspberry pi 4 and raspberry pi 5 with version 4.16.0.0 of the control application. Windows 10 native: build 19045 (same as virtualised Win 10), same .NET version, same CODESYS version. It seems that running CODESYS virtualized somehow messes with the deployment?
Last updated: 2025-06-23

Post by rajatdas2005 on Codesys Virtual control SL ^{CODESYS Forge talk (Post)}
Dear All, This is regarding Codesys Virtual control SL demo version. I am facing one issue. First I will describe the steps what I have followed till now. 1. In a PC I have Windows OS. Here Codesys IDE is installed, and also using the installer option of IDE I have also installed Codesys Virtual control SL. 2. A edge-gateway is also running in the same windows PC as local host. 3. Next I have a seperate PC with Ubuntu OS with docker installed. This machine is in the same network. 4. Now I have created a project in Windows machine using device "Codesys Virtual control SL". 5. In the Ubuntu machine I am running the Codesys Virtual control SL as docker and it is using the ubuntu machine network only. 6. Next using the localhost edge-gateway when I am searching the virtual control SL docker it is able to detect it. (screenshot attached) 7. But after creating the creadentials it is telling No Device is responding. 8. I have also checked the wireshark logs and able to see that in destination port 11740 data is coming. 9. From windows PC telnet ip 11740 is also working. 10. Ping is also working ===========================================LOGS ========================= sudo ss -tlnp | grep -E "(443|1217|4840|8080|11740)" LISTEN 0 10 10.135.114.142:4840 0.0.0.0: users:(("codesyscontrol.",pid=41864,fd=21)) LISTEN 0 10 172.18.0.1:4840 0.0.0.0: users:(("codesyscontrol.",pid=41864,fd=24)) LISTEN 0 10 172.17.0.1:4840 0.0.0.0: users:(("codesyscontrol.",pid=41864,fd=23)) LISTEN 0 10 127.0.0.1:4840 0.0.0.0: users:(("codesyscontrol.",pid=41864,fd=26)) LISTEN 0 10 192.168.122.1:4840 0.0.0.0: users:(("codesyscontrol.",pid=41864,fd=22)) LISTEN 0 5 0.0.0.0:11740 0.0.0.0: users:(("codesyscontrol.",pid=41864,fd=20)) LISTEN 0 128 0.0.0.0:8080 0.0.0.0: users:(("python3",pid=1280,fd=4)) LISTEN 0 10 172.19.0.1:4840 0.0.0.0: users:(("codesyscontrol.",pid=41864,fd=25))
Last updated: 2025-08-06

Post by superjojo2002 on Licensing info not available. ^{CODESYS Forge talk (Post)}
I updated the docker container runtime to version 4.11.0.0. and build the container with this "Dockerfile" FROM arm64v8/debian:11.6 RUN apt-get update RUN apt-get install -y wget sudo unzip libusb-1.0-0-dev procps ENV CDS_VERSION "4.11.0.0" ENV EDGE_VERSION "4.11.0.0" ENV URL "https://store-archive.codesys.com/ftp_download/3S/LinuxARM64/2302000039/$CDS_VERSION/CODESYS%20Control%20for%20Linux%20ARM64%20SL%20$CDS_VERSION.package" ENV EDGE_URL "https://store-archive.codesys.com/ftp_download/3S/EdgeGatewayLinux/000120/$EDGE_VERSION/CODESYS%20Edge%20Gateway%20for%20Linux%20$EDGE_VERSION.package" RUN wget --output-document=/tmp/codesys.package $URL && \ unzip -p /tmp/codesys.package '*codemeter*.deb' > /tmp/codemeter.deb && dpkg -i /tmp/codemeter.deb && \ unzip -p /tmp/codesys.package '*codesyscontrol*.deb' > /tmp/codesys.deb && dpkg -i /tmp/codesys.deb RUN wget --output-document=/tmp/edge.package $EDGE_URL && \ unzip -p /tmp/edge.package '*arm64.deb' > /tmp/edge.deb && dpkg -i /tmp/edge.deb EXPOSE 11740 1217 11743 ENTRYPOINT ["/bin/sh", "-c" , "/etc/init.d/codemeter start && /etc/init.d/codemeter-webadmin start && /etc/init.d/codesyscontrol start && /etc/init.d/codesysedge start && tail -f /dev/null"] Now cmu -x" returns root@sensoredge-field-netfield-produktmanagment:/# cmu -x cmu - CodeMeter Universal Support Tool. Version 8.00 of 2023-Nov-28 (Build 5967) for Linux/ARMHF 64-Bit Copyright (C) 2007-2023 by WIBU-SYSTEMS AG. All rights reserved. But still CODESYS development system reports that it needs a dongle and when I click install that "value cannot be null. Parameter name: containerToLicenses" It seems that Codemeter is forced to look for a dongle instead of a CMsoftcontainer. Can you confirm that CODESYS licensing works also when CODESYS is installed in a Docker container?
Last updated: 2024-03-21

Post by rita56re on AS Exclusive Temu $100 Discount Code {act892435} {act892435} for Free Stuff Canada ^{CODESYS Forge talk (Post)}
Yes, you can use the exclusive Temu discount codes "act892435" and "act892435" to receive a $100 discount on your purchases, along with the opportunity for free items. This offer is available for new customers in Canada, making it an excellent time to shop on Temu in Canada. • Temu New User Free Code Canada - [ACT892435] [ACT892435] • Temu New User Codes Reddit Canada - [ACT892435] [ACT892435] • Temu Coupon New User Code Free Shipping Canada -[ACT892435] [ACT892435] • Temu Code 2024 for New & Existing Customers Canada -[ACT892435] [ACT892435] • Temu Coupon $100 Off For New & Existing Customers Canada -[ACT892435] [ACT892435] • Temu Coupon Code Canada - [ACT892435] [ACT892435] • Temu Coupon $100 Off Canada - [ACT892435] [ACT892435] • Free Temu Coupon Codes Canada - [ACT892435] [ACT892435] • Temu Coupon New User Coupon Bundle Canada -[ACT892435] [ACT892435] • Temu Code New User 50% Off Canada -[ACT892435] [ACT892435] • Temu Code New User Discount Code Canada - [ACT892435] [ACT892435] • Temu Coupon New Customers Discount Code Canada -[ACT892435] [ACT892435] • Temu Coupon New Customer Coupon Code Canada - [ACT892435] [ACT892435] • Temu Code First Time User Coupon Canada - [ACT892435] [ACT892435] • Temu Code New User Coupon Code First Order Canada - [ACT892435] [ACT892435] • Temu Code New User Promo Coupon Code Canada - [ACT892435] [ACT892435] • Temu Coupon New Account Promo Coupon Code Canada - [ACT892435] [ACT892435] • Temu Coupon First Time User Discount Code Canada - [ACT892435] [ACT892435] • 30% Off Temu Code, Promo Codes + 26% Cash Back Canada - [ACT892435] [ACT892435] • Redeem $100 Off Temu Coupon Code Canada - [ACT892435] [ACT892435] • Temu Coupon $100 Off For New & Existing Customers Free Shipping Canada - [ACT892435] [ACT892435] • Temu 100 Off Coupon Code Legit Canada - [ACT892435] [ACT892435] • Temu 100 Off Coupon Codes Reddit Canada - [ACT892435] [ACT892435] • Temu 100 Off Coupon Code For Existing Users Canada - [ACT892435] [ACT892435] • Temu Coupon 100 Off Coupon Code UK Canada - [ACT892435] [ACT892435] • Temu Coupon Codes 100 Percent Off Canada - [ACT892435] [ACT892435] • Temu Code $100 Off How Does It Work Canada - [ACT892435] [ACT892435] • Temu Code $100 Off Canada - [ACT892435] [ACT892435] • Temu Code $100 Off For Existing Customers Canada - [ACT892435] [ACT892435] • Temu Code $100 Off For Existing Customers First Order Canada - [ACT892435] [ACT892435] • Temu Code $100 Off 2024 Canada - [ACT892435] [ACT892435] • Temu 100 Off Coupon Bundle Canada - [ACT892435] [ACT892435] • 100 Doller Coupon Code Canada - [ACT892435] [ACT892435] • Temu Code 100 Value Coupon Bundle Canada - [ACT892435] [ACT892435] • 100 Off Promo Coupon Codes Canada - [ACT892435] [ACT892435]
Last updated: 2024-10-26

Post by denizerm on Deploy Control SL cant find Podman ^{CODESYS Forge talk (Post)}
Hello, CODESYS seems to have problems finding the container engine. In the "Deploy Control SL" window, after connecting via ssh, it simply says: [INFORMATION] Connected successfully! [INFORMATION] Successfully connected to target (192.168.4.199) [WARNING] Error detecting container architecture running podman info yields normal results. My podman info output is as follows: home/Admin$ podman info host: arch: amd64 buildahVersion: 1.35.3 cgroupControllers: - cpu - memory - pids cgroupManager: systemd cgroupVersion: v2 conmon: package: Unknown path: /usr/bin/conmon version: 'conmon version 2.1.10, commit: affab49967eb62f75d2a47398344ab053326289f' cpuUtilization: idlePercent: 99.36 systemPercent: 0.3 userPercent: 0.34 cpus: 4 databaseBackend: sqlite distribution: codename: scarthgap distribution: redagv version: 1.0.0 eventLogger: journald freeLocks: 2040 hostname: secure-automation-os idMappings: gidmap: - container_id: 0 host_id: 1000 size: 1 - container_id: 1 host_id: 100000 size: 65536 uidmap: - container_id: 0 host_id: 1100 size: 1 - container_id: 1 host_id: 100000 size: 65536 kernel: 6.6.65-intel-pk-standard linkmode: dynamic logDriver: journald memFree: 6115598336 memTotal: 8086278144 networkBackend: cni networkBackendInfo: backend: cni dns: {} ociRuntime: name: crun package: Unknown path: /usr/bin/crun version: |- crun version 1.14.3.0.0.0.8-89d44-dirty commit: 89d44467e3b410b73f2065756a12789be45b855b rundir: /run/user/1100/crun spec: 1.0.0 +SYSTEMD +SELINUX +APPARMOR +CAP +SECCOMP +EBPF +YAJL os: linux pasta: executable: /usr/bin/pasta package: Unknown version: "" remoteSocket: exists: true path: /run/podman-shared/podman.sock security: apparmorEnabled: false capabilities: CAP_CHOWN,CAP_DAC_OVERRIDE,CAP_FOWNER,CAP_FSETID,CAP_KILL,CAP_NET_BIND_SERVICE,CAP_SETFCAP,CAP_SETGID,CAP_SETPCAP,CAP_SETUID,CAP_SYS_CHROOT rootless: true seccompEnabled: true seccompProfilePath: "" selinuxEnabled: false serviceIsRemote: true slirp4netns: executable: /usr/bin/slirp4netns package: Unknown version: |- slirp4netns version 1.2.0-beta.0+dev commit: unknown libslirp: 4.7.0 SLIRP_CONFIG_VERSION_MAX: 4 libseccomp: 2.5.5 swapFree: 0 swapTotal: 0 uptime: 1h 36m 10.00s (Approximately 0.04 days) variant: "" plugins: authorization: null log: - k8s-file - none - passthrough - journald network: - bridge - macvlan - ipvlan volume: - local registries: localhost:5000: Blocked: false Insecure: true Location: localhost:5000 MirrorByDigestOnly: false Mirrors: null Prefix: localhost:5000 PullFromMirror: "" search: - localhost store: configFile: /home/serviceuser/.config/containers/storage.conf containerStore: number: 2 paused: 0 running: 2 stopped: 0 graphDriverName: overlay graphOptions: {} graphRoot: /data/containerfiles graphRootAllocated: 119952025600 graphRootUsed: 13801246720 graphStatus: Backing Filesystem: extfs Native Overlay Diff: "true" Supports d_type: "true" Supports shifting: "false" Supports volatile: "true" Using metacopy: "false" imageCopyTmpDir: /var/tmp imageStore: number: 4 runRoot: /run/user/1100/containers transientStore: false volumePath: /data/containerfiles/volumes version: APIVersion: 5.0.2-dev Built: 1711987427 BuiltTime: Mon Apr 1 16:03:47 2024 GitCommit: bb81e85a430fa95d23a15b77c717fd68bf06ebf2 GoVersion: go1.22.12 Os: linux
Last updated: 2025-10-22

Post by manuknecht on Persistence Manager does not save alphabetically first value ^{CODESYS Forge talk (Post)}
After some more digging I realized that I get an error on the PLC Logger saying PersistenceChannel: 150 (invalid type in data: SimpleLibrary). I suppose the issue could be found in the ConfigData, which is automatically generated and which looks like this: 1 9##83 SimpleLibrary#GVL.aMoreZeros.[1]#0#64512#15#0 <[2]#0#64520#15#0 <[3]#0#64528#15#0 <[4]#0#64536#15#0 <#0#64544#15#0 <[6]#0#64552#15#0 <<lrVar#0#64560#15#0 <strVar#0#64428#16#80 <uiDummy#0#64370#11#0 Perhaps the fact that the variable is stored within a library confused the compiler? I tried changing the PersistenceChannel parameters to xCompressTags := FALSE which changed the entry in the data file from _xCompressTags BOOL:TRUE _xCompressTags BOOL:FALSE but the actual content of the data file and also the config data did not change.
Last updated: 2023-10-17

Post by janber0206 on Gateway doesn't come online, regarding a working internet connection ^{CODESYS Forge talk (Post)}
Solved EN: The Problem is that the Codesys Edge-Gateways have a License with a runtime of an half year, as long the Gateways are online they will self renew themselfs. In my Case the RevPi was more than a year offline and so the Edge-Gateway was not working anymore. The solution: I accessed a laptop that was directly connected to the RevPi. I installed the Codesys service tool and renewed the certificate manual. DE: Das Propblem ist das die Codesys Edge-Gatways eine Lizenz haben die nur ein halbes Jahr gültig ist. Solange das Gateway eine Internet verbindung hat aktualisiert sich das Zertifikat von alleine. In meinem Fall war das Gateway aber über ein Jahr offline und hat somit nicht mehr funktioniert. Die Lösung: Ich hab auf einen Laptop von Kunden mit TeamViewer zugegriffen, der Laptop wurde mit Kabel direkt mit RevPi verbunden. Codesys Service Tool installiert und dann das Gatewayzertifikat aktualisiert.
Last updated: 2023-10-26

Post by naps on cant install runetime on 750-8202 ^{CODESYS Forge talk (Post)}
Hello, im trying to install the 3.5 Runtime on a a fresh image on my 750-8202. Product Description: WAGO 750-8202 PFC200 CS 2ETH RS Firmware Revision: 03.10.08(22) ~~~ df -h Filesystem Size Used Available Use% Mounted on ubi0:rootfs.1 82.5M 66.5M 11.8M 85% / devtmpfs 117.8M 16.0K 117.8M 0% /dev none 118.3M 12.0K 118.3M 0% /tmp none 118.3M 0 118.3M 0% /media none 4.0M 136.0K 3.9M 3% /var/log none 118.3M 112.0K 118.2M 0% /var/run none 118.3M 0 118.3M 0% /var/lock none 118.3M 0 118.3M 0% /var/tmp none 118.3M 0 118.3M 0% /sys/fs/cgroup tmpfs 118.3M 48.0K 118.2M 0% /run /dev/ubi0_1 58.6M 3.4M 52.2M 6% /home /dev/ubi0_1 58.6M 3.4M 52.2M 6% /settings /dev/ubi0_1 58.6M 3.4M 52.2M 6% /log ~ After installation and reboot i have still the wago webinterface. No runtime on Information Tab and the Runtime button from the configuration tab is lost. iv try it with firmware 22 and 21. Same problem. What can i do?
Last updated: 2024-09-29

Post by egau on Hard shutdown: no code on device after power on ^{CODESYS Forge talk (Post)}
This explanation aligns with the issues we’re experiencing with our machines. The scenario I described is happening with one of them (let’s call it Machine A). This machine is identical to another one (Machine B), except for some custom code that facilitates communication with an external Beckhoff PLC for MES integration in the production line. Machine B has been powered on and off daily for at least three months and has never had this problem. Given that, I highly doubt the MES custom code is the cause of the code corruption. This being said, your explanation does seem plausible. However, if faulty EtherCAT cables were the issue, why wouldn't the error occur during normal operation? Why would bad cables only cause problems during a hard shutdown? One last question: When you encountered this behavior, did you see a similar error in your logs? i.e, an "AccessViolation" exception in the EtherCAT Task?
Last updated: 2024-10-03

Post by breiter on Frustration-Fueled Feedback on Project File Management and Git Integration ^{CODESYS Forge talk (Post)}
Hi, supporting a text based storage format is on our roadmap, see https://www.codesys.com/the-system/releases-updates-lifecycle/release-plan-roadmap.html It will be an Add-On feature called "File Based Storage" for the professional developer edition. Structured text POUs will be stored as plain text. Other graphical languages will remain in an xml format. You will be able to switch the storage type for projects. Certain workflows will become easier this way. Nevertheless restrictions will remain because of CODESYS specific storage logic (for example how methods below function blocks are stored as file). So merging using our Git Integration Add-On remains the recommended workflow. A workflow involving Visual Studio Code as the main IDE is not supported. Simply because many topics like library management, task configuration or fieldbus configurators are not available for VS Code. A PLC project is a lot more than just some ST POUs. Best Regards
Last updated: 2024-10-16

Post by edvard-munch on How I can get "Done flag" for "Modbus Slave Channel"? ^{CODESYS Forge talk (Post)}
This is from 10 years ago, I know. But I have been using (SLAVE_DEVICE.iChannelIndex = CHANNEL_NUMBER) AND (SLAVE_DEVICE.xDone) I suppose that it shows xDone for the channel that shows up in the iChannelIndex at the same cycle? It seems to be working properly for two devices that I have been using it before But now I have another device and using two write channels, for one register each. One channel works properly and returns DONE flag When another channel is triggered, I see that it shows up in iChannelIndex, but flag DONE not received, but no Error for the channel. Also, when i check the register in the device it's evident that data has been transferred. Is this could happen sometimes with CODESYS, so DONE flag not received? Or this is a problem with a given device? With this certain register
Last updated: 2024-12-19

Post by peterkcontrols on TargetVisu started in windowed or not full screen ^{CODESYS Forge talk (Post)}
Thanks for the response. I have found this file in two places, I have updated the text in both but it didnt work. Am I missing something on the Codesys side. How do you restart the soft plc, I have been stopping it and starting it. The Visu screen come up but still in full screen mode. Here are the two locations of this file: C:\Program Files\Codesys Control\GatewayPLC\AppDataFiles\CODESYSControlWinV3x64 and C:\Program Files\CODESYS 3.5.20.50\GatewayPLC\AppDataFiles\CODESYSControlWinV3x64 Here is the contents of targetvisuextern.cfg [ComponentManager] [CmpTargetVisu] ; The Window... settings can be used for displaying the targetvisualization in a window instead of fullscreen WindowType=0 WindowPositionX=0 WindowPositionY=0 WindowSizeWidth=1024 WindowSizeHeight=768 HideCursorCompletely=1 [SysWindow] ;Windows.CloseOnAltF4=0 ;Windows.CloseOnWM_CLOSE=0 [CmpLog] ;Logger.0.Name=TvExtLogger ;Logger.0.Enable=1 ;Logger.0.MaxEntries=1000 ;Logger.0.MaxFileSize=5000 ;Logger.0.MaxFiles=3 ;Logger.0.Backend.0.ClassId=0x0000010B ;sends logger messages to SysOut ;Logger.0.Backend.1.ClassId=0x00000104 ;writes logger messages in a file ;Logger.0.Backend.2.ClassId=0x00000135 ;sends logger messages as UDP syslog
Last updated: 2025-02-26

Post by rene-h on ClientFilter used the same Client ID 2 times - Bug? ^{CODESYS Forge talk (Post)}
Hello, like the topic name says, i have a problem on one Visu which i cannot reproduce on another Visu. We filter buttons with input locks and visible items with [CURRENTCLIENTID] on different WebVisu's with different ID's, and one time the itfClient used the same Client ID for 2 Clients, so the Visualization on the first ID was wrong, because that one which connected after did not have the same permissions like the first, so the first one was blocked. We read the Clients with the VisuClientIteration project: //count active clients gCli.iNumberOfClients:=gCli.iNumberOfClients+1; // if client is active write data to global struct IF gCli.iNumberOfClients > 0 THEN gCli.astClientInfo[gCli.iNumberOfClients-1].iClientID:=itfClient.ClientId ; gCli.astClientInfo[gCli.iNumberOfClients-1].stCurrentVisu:=itfClient.CurrentVisuName; gCli.astClientInfo[gCli.iNumberOfClients-1].wsUserName:=itfClient.UserName; gCli.astClientInfo[gCli.iNumberOfClients-1].sIpAddress:=itfClient.GetIPv4Address(); gCli.astClientInfo[gCli.iNumberOfClients-1].ClientType:=itfClient.ClientType; END_IF Runtime from the device: 3.5.19.20 Codesys we use: 3.5.20.10 I added a screenshot where the same ID exists 2 times. Thanks for your answers.
Last updated: 2025-05-14

Post by jakubmphoenix on EtherCAT Master on RaspberryPi with EtherCAT Slave on Beckhoff ^{CODESYS Forge talk (Post)}
Hello everyone, I’m currently working on setting up an EtherCAT Master using CODESYS on a Raspberry Pi, and I’ve run into some issues I could use help with. Project Setup: EtherCAT Master: Raspberry Pi with CODESYS Control for Raspberry Pi 64 SL installed EtherCAT Slave: Beckhoff CX5130 with EK1200 coupler I/O Module: EL2008 License Module: EL6070-0033 I’ve installed the required CODESYS packages and the Linux gateway on the Raspberry Pi. In my project, I added the EtherCAT Master with the appropriate port settings and scanned for devices. The CX5130 shows up as a slave, but communication fails—I'm getting error messages and can't access the outputs. Specifically: The EL2008 output module isn’t recognized properly in CODESYS. There’s no option to communicate with it through the CX5130. I’ve tried connecting via both the Raspberry Pi’s built-in Ethernet port and an external network card. I've attached screenshots showing the errors I get in CODESYS and the devices detected via TwinCAT for reference. Any help or suggestions would be greatly appreciated! Thanks in advance! EMERGENCY FROM DEVICE 1001 ERROR CODE 16#A000 Error register 16#02 Error field: 16#02 Error field : 16#0E 16#04 16#00 16#04 16#00
Last updated: 2025-07-16

Post by mavitia on Application based license problem - Modbus TCP ^{CODESYS Forge talk (Post)}
I am running ubuntu on a raspberry pi, and installed an application based license Control Basic M on it, it runs a demo program fine, does not timeout etc. however, when I add a modbus TCP device, I start getting errors: <Entry severity="error" component="CmpApp" user="nobody" timestamp="12/18/2023 3:49:42 PM" infoId="24">Online change denied. Application Application is in exception state!</Entry> <Entry severity="error" component="CmpApp" user="nobody" timestamp="12/18/2023 3:49:42 PM" infoId="68">Download failed: Application=Application</Entry> <Entry severity="exception" component="CmpApp" user="nobody" timestamp="12/18/2023 3:49:41 PM" infoId="0">Application app=Application has invalid license metrics!</Entry> the modbus tcp slave runs, and the counter ticks up, however, when I call the variables on the %IX0.0 in my program, and try to upload the changes, I am getting the error messages which stop the program as far as I understand, the application based, M includes 2 fieldbus instances, but on the other side is fairly new, anything obvious I am missing out here?
Last updated: 2023-12-18

Post by spiessli on Softmotion axis to CANopen Maxon IDX drive ^{CODESYS Forge talk (Post)}
Thanks for the advise, indeed, this was somewhat, what my intention was. I tried around again with EDSes and DCFs, anyway. It appears that the DCFs end up in a subfolder in the attach device dialog. Astonishingly, when attaching the DCF version I get a device in the device tree, where I can add a SoftMotion axis, whereas when I attach the device not in the subfolder, then I cannot. Further astonishingly, when looking in the CANopen parameters in supported profiles, "402" is listed in the case of the DCF variant, whereas in the EDS variant "0" is shown. Comparing EDS and DCF files I cannot guess, where the difference is coming from. I cannot tell either why I have always attached the EDS variant and apparantly never the DCF variant. As I am not in the lab right now, I cannot test if the connection actually is working. Thanks again, spiessli
Last updated: 2024-01-07

Post by forest on SM Drive license error ^{CODESYS Forge talk (Post)}
Hi, when it comes about license, I used INVTmatic Studio, which uses Codesys, for programming INVT plc. I bought Codesys Modbus license, it was not expensive, and then realised that INVT didn't have License Manager option (greyed out in program) which is needed for using of Codesys License. I contacted support from INVT, but developers told me that option is still not available. So depending on environment for programming Codesys, you can or not use Modbus license. Good thing about this version of Modbus TCP it works both direction. I could send commands and receive feedbacks from drive. But communication stops after 30 mins. So I used simple version of ethernet modbus which is somewhere in INVT or Condesys library (I can check tomorrow) which works only one way. I could send cmd to drive, and control it, but didn't have any feedback, like some readings back in PLC. which is bad, but at least I could start it and it didn't fail after 30 mins.
Last updated: 2024-01-10

Post by tim-roelant on Profinet fault with codesys control V3 - Receive packet error ^{CODESYS Forge talk (Post)}
I have set up a brandnew Beckhoff panel pc with a codesys control runtime V3. I configured it together with 2 profinet field devices: a 16in/16out IO module from Turck and an MTS linear encoder. The machine works fine untill all of a sudden the communication breaks and the profinet participants become unreachable. At that point I can still ping the device, but the profinet master does not find them anymore: When i do a scan they are not found. When i do a cold restart, the profinet master becomes active again and the devices are found again. In the log i get Ethercat packet receive error: sysethernet. I am a little confused, there is no ethercat device in the device tree. I already set the send clock and the reduction ratio to higher values, but without result. Can codesys be configured, so that the communication re-establishes without doing the cold reset? This is very annoying and is causing a lot of prodution losses. regards Tim
Last updated: 2024-02-27

Post by tim-roelant on Profinet fault with codesys control V3 - Receive packet error ^{CODESYS Forge talk (Post)}
I have set up a brandnew Beckhoff panel pc with a codesys control runtime V3. I configured it together with 2 profinet field devices: a 16in/16out IO module from Turck and an MTS linear encoder. The machine works fine untill all of a sudden the communication breaks and the profinet participants become unreachable. At that point I can still ping the device, but the profinet master does not find them anymore: When i do a scan they are not found. When i do a cold restart, the profinet master becomes active again and the devices are found again. In the log i get Ethercat packet receive error: sysethernet. I am a little confused, there is no ethercat device in the device tree. I already set the send clock and the reduction ratio to higher values, but without result. Can codesys be configured, so that the communication re-establishes without doing the cold reset? This is very annoying and is causing a lot of prodution losses. regards Tim
Last updated: 2024-02-27

Post by tim-roelant on Profinet fault with codesys control V3 - Receive packet error ^{CODESYS Forge talk (Post)}
I have set up a brandnew Beckhoff panel pc with a codesys control runtime V3. I configured it together with 2 profinet field devices: a 16in/16out IO module from Turck and an MTS linear encoder. The machine works fine untill all of a sudden the communication breaks and the profinet participants become unreachable. At that point I can still ping the device, but the profinet master does not find them anymore: When i do a scan they are not found. When i do a cold restart, the profinet master becomes active again and the devices are found again. In the log i get Ethercat packet receive error: sysethernet. I am a little confused, there is no ethercat device in the device tree. I already set the send clock and the reduction ratio to higher values, but without result. Can codesys be configured, so that the communication re-establishes without doing the cold reset? This is very annoying and is causing a lot of prodution losses. regards Tim
Last updated: 2024-02-27

Post by tim-roelant on Profinet fault with codesys control V3 - Receive packet error ^{CODESYS Forge talk (Post)}
I have set up a brandnew Beckhoff panel pc with a codesys control runtime V3. I configured it together with 2 profinet field devices: a 16in/16out IO module from Turck and an MTS linear encoder. The machine works fine untill all of a sudden the communication breaks and the profinet participants become unreachable. At that point I can still ping the device, but the profinet master does not find them anymore: When i do a scan they are not found. When i do a cold restart, the profinet master becomes active again and the devices are found again. In the log i get Ethercat packet receive error: sysethernet. I am a little confused, there is no ethercat device in the device tree. I already set the send clock and the reduction ratio to higher values, but without result. Can codesys be configured, so that the communication re-establishes without doing the cold reset? This is very annoying and is causing a lot of prodution losses. regards Tim
Last updated: 2024-02-27

Sort by relevance or date