Post by micik on Start Codesys project and then execute python script from command line ^{CODESYS Forge talk (Post)}
Hello, by searching the forum, I have found an example of batch script that can be used to start codesys projct by temporarily setting env variables. However, I'm not sure how to modify this to start Codesys 3.5.20 and whether or not I need to specify "profile" with Codesys version at all. @echo off SET PROJECT=D:\TestScripts\Data\OnlineTest.project SET VARIABLES=POU.testint,POU.testoutput start /wait CoDeSys.exe --profile="CoDeSys V3.4 SP3" --noUI --runscript="D:\TestScripts\Forum_Environment.py" I have tried the following just to open the test project: SET PROJECT=C:\TEST\Example.project start CODESYS.exe --profile="CODESYS V3.5 SP20 Patch 2" But I'm not sure how to specify this project to be open after py script is executed. The py script should first add required library to the project and then project should be open.
Last updated: 2024-09-30

Post by ben1 on Help understanding analog in-/outputs ^{CODESYS Forge talk (Post)}
Hi there mate Most PLC's have a very similar concept with AI/AO - have you used any other software before? I have not used a Wago before myself, but I assume the concept would very much be: 1. Add the analog in & out cards to your hardware config. 2. Setup the raw input scaling on the hardware (eg. 4 - 20mA = 4000 - 20000) 3. Use a built in or homemade scaling block to scale your input as needed (eg. 4000 - 20000 = -100 - 2000kPa. 4. Write code as required 5. Scale output as needed (eg. 0 - 100% = 0-10000 = 0 - 10V) Is this the information you require?
Last updated: 2024-12-15

Post by struccc on Problem Reading Registers via Modbus from non Codesys device ^{CODESYS Forge talk (Post)}
Hi, Might be a good idea first to try out the connection and the device with some handy software, like Modbus Poll. There you can see better, what's really going on... - Is it really connected? - What error code does it return? - Can it read from the register address? - Maybe try Input registers and Holding Registers - can make a difference - Sometimes register addresses are messed up: shifted +-1 (mixing of 2 standards) - Sometimes register addresses start with offset 30000, 40000 ... - Are you using the right protocol? - Is it RTU or TCP? Maybe ASCII? - Can even have a look at the data packets, etc... All this is easier to figure out first with some modbus utility... and then to set it up in CODESYS should not be an issue. P.
Last updated: 2025-03-09

Post by r-c-r on SM3RaspiStepper 0.0.0.6 issue ^{CODESYS Forge talk (Post)}
Hello, I noticed that version 0.0.0.6 is now available, so I tested it using CODESYS V3.5 SP19 Patch 7 and SoftMotion 4.17.0.0. While the project compiles and downloads without issues, I encountered a problem with the 'Enable: GPIO pin number that is set when the axis is enabled (with MC_Power) (0: not used)' functionality — it no longer works (HIGH level not present at the output pin). I observed the same behavior with version 0.0.0.5, whereas version 0.0.0.4 functions correctly. Could you help me identify what might be causing this issue or suggest how to resolve it? Thanks.
Last updated: 2025-03-19

Post by valec on Connect local Asem HMI runtime to local Codesys Control Win V3 x64 ^{CODESYS Forge talk (Post)}
I have a project made on a PL700 PLC with Codesys and an Asem Premium HMI panel. I don't have access to the physical PLC right now, so I'm trying to use Codesys Control Win V3 x64. I created the application and loaded "Codesys Control Win V3 x64" without errors, then I activate "Start PLC" from the tray. Asem cannot connect. I tried to use "localhost" or the local IP address and it doesn't work (it's the "CoDeSys Soft PLC Communication Driver"). I need to connect my local Asem runtime to a virtual Codesys application on my PC. How can I do it?
Last updated: 2024-03-26

Post by m83coding on Raspberry Pi Codesys SPI Master ^{CODESYS Forge talk (Post)}
Hello, I am trying to control shift registers 74HC596 and 74HC165 via Raspberry PI with SPI interface. So far I did it with a Microcontroller and now I wanna upgrade my Projekt with Raspberry Pi and Codesys Software to be more flexible. I tried to adapt PiFace Function Block to just send or recive a 8 bit via SPI interface of the my Raspberry Pi. With following code (see attached screenshots) * PLC_PRG * PiFaceDigital * PiFaceDigital.write8 * PiFaceDigital.read8 I have a signal at SCK and MOSI pin of the PI, so far so good. But I really struggle with the unterstanding of the code. Is there some detailed description of each line of code? Or is there somebody in the community who can explain each line of code? Or is there a more simple way to send / recive 8 bit via SPI? Manuel
Last updated: 2024-04-23

Post by zer0g on Modbus Client Request Not Processed ^{CODESYS Forge talk (Post)}
I'm using the code bellow which is based on the Codesys example: FUNCTION_BLOCK MODBUS_master_example_ST VAR initDone : BOOL := FALSE; aIPAddress : ARRAY [0..3] OF BYTE := [127,0,0,1]; clientTcp: ModbusFB.ClientTcp; // buffer to read input registers aDataInputRegisters : ARRAY[0..9] OF UINT; // some client requests clientRequestReadInputRegisters: ModbusFB.ClientRequestReadInputRegisters; xExecute: BOOL; END_VAR IF NOT initDone THEN initDone := TRUE; // configure clientTcp clientTcp(aIPaddr:=aIPAddress, uiPort:=502, udiLogOptions := ModbusFB.LoggingOptions.All); // configure clientRequestReadInputRegisters clientRequestReadInputRegisters(rClient:=clientTcp, uiUnitId:=1, udiTimeout:=TO_UDINT(T#1000MS)); END_IF // call the client FB's clientTcp(); clientRequestReadInputRegisters(rClient:=clientTcp,xExecute := xExecute AND NOT clientRequestReadInputRegisters.xBusy ,uiStartItem:=2, uiQuantity:=3, pData:=ADR(aDataInputRegisters[0])); As you can see the clientTCP is called cyclically with the same result.
Last updated: 2024-05-30

Post by kazuhiro on Problems using MySql Library and SysProcessExecuteCommand2 together ^{CODESYS Forge talk (Post)}
I use fbMsSQL_compact(FUN) of the MySQL Library to write data to the database. There is no problem when writing data using only fbMsSQL_compact(FUN). However, when I try to write data obtained using SysProcessExecuteCommand2 to the database using fbMsSQL_compact(FUN), an error message "Dest server on ip address:xxx.xxx.xxx.xxx and port:1433 is unreachable" appears and writing is not possible. From what I have researched, it seems that writing is not completed in one cycle of fbMsSQL_compact(FUN), and when SysProcessExecuteCommand2 is executed first in the second cycle, the work done in one cycle of fbMsSQL_compact(FUN) is reset. Could you please give me some advice?
Last updated: 2024-06-18

Post by kazuhiro on Problems using MySql Library and SysProcessExecuteCommand2 together ^{CODESYS Forge talk (Post)}
I use fbMsSQL_compact(FUN) of the MySQL Library to write data to the database. There is no problem when writing data using only fbMsSQL_compact(FUN). However, when I try to write data obtained using SysProcessExecuteCommand2 to the database using fbMsSQL_compact(FUN), an error message "Dest server on ip address:xxx.xxx.xxx.xxx and port:1433 is unreachable" appears and writing is not possible. From what I have researched, it seems that writing is not completed in one cycle of fbMsSQL_compact(FUN), and when SysProcessExecuteCommand2 is executed first in the second cycle, the work done in one cycle of fbMsSQL_compact(FUN) is reset. Could you please give me some advice?
Last updated: 2024-06-18

Post by kuegerls on SysProcessExecuteCommand2 and CANopen Device ^{CODESYS Forge talk (Post)}
Hello, CODESYS Control is running on my RevPi, and my system communicates over a CANbus with a master using the ConnectCan module (Slave - CANopen Device). The communication works perfectly fine so far. However, as soon as I call a Python script with "SysProcessExecuteCommand2" that creates a CSV file and executes without errors, the master does not adopt any changes to the Transmission Process Data Objects (TPDOs). I don't quite understand what one has to do with the other, and perhaps someone can help me with this. Here is my script call: SysProcess.SysProcessExecuteCommand2(pszCommand:='python /home/pi/test.py', pszStdOut:=sCMDOutput, udiStdOutLen:= SIZEOF(sCMDOutput), pResult := ADR(eResult)); Thank you in advance! Best regards, Stefan
Last updated: 2024-06-20

Post by jasperclauwaert on Persistent Retain Variables Not Visible in Online View (WAGO PFC100 + CODESYS) ^{CODESYS Forge talk (Post)}
Hi everyone, I’m working on a WAGO PFC100 with CODESYS. During development everything worked fine, but in the final stage I set several variables to PERSISTENT RETAIN. When I go online, most of these persistent variables cannot be monitored. Instead, I see: <Value of the expression cannot be retrieved> Interestingly, a few variables do show their values correctly, but the majority do not. The variables are not used as pointers or in any unusual way. The application compiles and runs without errors. Has anyone experienced this before? Is this a known issue with PFC100 or CODESYS? Any ideas on what could cause this behavior? Thanks in advance! Jasper
Last updated: 2025-10-23

Post by jasperclauwaert on Persistent Retain Variables Not Visible in Online View (WAGO PFC100 + CODESYS) ^{CODESYS Forge talk (Post)}
Hi everyone, I’m working on a WAGO PFC100 with CODESYS. During development everything worked fine, but in the final stage I set several variables to PERSISTENT RETAIN. When I go online, most of these persistent variables cannot be monitored. Instead, I see: <Value of the expression cannot be retrieved> Interestingly, a few variables do show their values correctly, but the majority do not. The variables are not used as pointers or in any unusual way. The application compiles and runs without errors. Has anyone experienced this before? Is this a known issue with PFC100 or CODESYS? Any ideas on what could cause this behavior? Thanks in advance! Jasper
Last updated: 2025-10-23

Post by eschwellinger on Problems connecting to Codesys 4.9.0.0 runtime on my Wago PFC200 ^{CODESYS Forge talk (Post)}
I've send out a workaround for this.. Best Regards Edwin
Last updated: 2023-08-26

Post by eschwellinger on CODESYS Automation Server Connector for 3.5 SP11 ^{CODESYS Forge talk (Post)}
https://store.codesys.com/en/codesys-automation-server-connector.html Programming System CODESYS Development System V3.5.15.0 or higher
Last updated: 2023-08-30

Post by janderson on Ethercat scan for devices not picking up EL7041 as a softmotion axis ^{CODESYS Forge talk (Post)}
also my ethercat bus won't run.
Last updated: 2023-09-02

Post by jegerjon on VPN ^{CODESYS Forge talk (Post)}
Hi, witch VPN provider for remote PLC Acess do you use/recomend? Preferedbly one where you can Grant certain users acess to specific controllers.
Last updated: 2023-09-06

Post by jegerjon on VPN ^{CODESYS Forge talk (Post)}
Hi, witch VPN provider for remote PLC Acess do you use/recomend? Preferedbly one where you can Grant certain users acess to specific controllers.
Last updated: 2023-09-06

Post by jegerjon on VPN ^{CODESYS Forge talk (Post)}
Hi, witch VPN provider for remote PLC Acess do you use/recomend? Preferedbly one where you can Grant certain users acess to specific controllers.
Last updated: 2023-09-06

Post by eschwellinger on Project compiling error in Simulation mode ^{CODESYS Forge talk (Post)}
I fear you need to update if you need a solution for this.
Last updated: 2023-09-08

Post by imdatatas on Detecting if a client is connected to webvisu server ^{CODESYS Forge talk (Post)}
Thank you @dgirard Your idea and above description helped me what i was looking for.
Last updated: 2023-11-08

Post by pflot59 on Migration von "CODESYS Control for PFC200 SL" zu WAGO FW26 "CODESYS V3.5.19.2" ^{CODESYS Forge talk (Post)}
You can find a guide here : https://techdocs.wago.com/Software/eCOCKPIT_Migration/en-US/index.html
Last updated: 2023-11-21

Post by pflot59 on Migration von "CODESYS Control for PFC200 SL" zu WAGO FW26 "CODESYS V3.5.19.2" ^{CODESYS Forge talk (Post)}
You can find a guide here : https://techdocs.wago.com/Software/eCOCKPIT_Migration/en-US/index.html
Last updated: 2023-11-21

Post by wbj0t on connect IDE to plc that uses modem ppp ^{CODESYS Forge talk (Post)}
Thanks for reply. I did all understand, thanks you :)
Last updated: 2024-07-01

Post by hyys12 on How to use/create SOTU in LD program ^{CODESYS Forge talk (Post)}
Yes. R_TRIG and F_TRIG works exactly like needed for this.
Last updated: 2024-07-11

Post by strannik on SoftMotion SML ^{CODESYS Forge talk (Post)}
Good afternoon. Thank you colleagues for your responsiveness and willingness to help. I've already figured it out.
Last updated: 2024-07-15

Sort by relevance or date